The active use of solid fossil fuels (coal) in the production of heat and electricity has led to significant pollution, climate change, environmental degradation, and an increase in morbidity and mortality. Many countries (in particular, European ones, China, Japan, the USA, Canada, etc.) have launched programs for using plant and agricultural raw materials to produce heat and electricity by burning them instead of or together with traditional fuels. It is a promising solution to produce slurry fuels, based on a mixture of coal processing, oil refining and agricultural waste. This paper presents the results of experimental research into the formation and assessment of the most hazardous emissions (sulfur and nitrogen oxides) from the combustion of promising coal slurry fuels with straw, sunflower and algae additives, i.e. the most common agricultural waste. A comparative analysis has been carried out to identify the differences in the concentrations of sulfur and nitrogen oxides from the combustion of typical coal, coal processing waste, as well as fuel slurries with and without plant additives. It has been shown that the concentration of sulfur and nitrogen oxides can be reduced by 62–87% and 12–57%, respectively, when using small masses of plant additives (no more than 10 wt%) and maintaining high combustion heat of the slurry fuel. However, the use of algae and straw in the slurry composition can increase the HCl emissions, which requires extra measures to fight corrosion. A generalizing criterion of slurry fuel vs. coal efficiency has been formulated to illustrate significant benefits of adding plant solid waste to coal-water slurries containing petrochemicals. Straw and sunflower waste (10 wt%) were found to be the best additives to reduce the air pollutant emissions.

Attenuated backscatter profiles retrieved by the space borne active lidar CALIOP on-board CALIPSO satellite were used to measure the vertical distribution of smoke aerosols and to compare it against the ECMWF planetary boundary layer height (PBLH) over the smoke dominated region of Indo-Gangetic Plain (IGP), South Asia. Initially, the relative abundance of smoke aerosols was investigated considering multiple satellite retrieved aerosol optical properties. Only the upper IGP was selectively considered for CALIPSO retrieval based on prevalence of smoke aerosols. Smoke extinction was found to contribute 2–50% of the total aerosol extinction, with strong seasonal and altitudinal attributes. During winter (DJF), smoke aerosols contribute almost 50% of total aerosol extinction only near to the surface while in post-monsoon (ON) and monsoon (JJAS), relative contribution of smoke aerosols to total extinction was highest at about 8 km height. There was strong diurnal variation in smoke extinction, evident throughout the year, with frequent abundance of smoke particles at lower height (<4 km) during daytime compared to higher height during night (>4 km). Smoke injection height also varied considerably during rice (ON: 0.71 ± 0.65 km) and wheat (AM: 2.34 ± 1.34 km) residue burning period having a significant positive correlation with prevailing PBLH. Partitioning smoke AOD against PBLH into the free troposphere (FT) and boundary layer (BL) yield interesting results. BL contribute 36% (16%) of smoke AOD during daytime (nighttime) and the BL-FT distinction increased particularly at night. There was evidence that despite travelling efficiently to FT, major proportion of smoke AOD (50–80%) continue to remain close to the surface (<3 km) thereby, may have greater implications on regional climate, air quality, smoke transport and AOD-particulate modelling.

Coal-Gas replacement project has been implemented to decrease haze pollution in China in recent years. Airborne arsenic (As) mostly originates from coal burning processes. It is noteworthy to compare the distribution of arsenic fraction in PM₂.₅ before and after coal-gas replacement. Eighty PM₂.₅ samples were collected in Baoding in December 2016 (coal dominated year) and December 2017 (gas dominated year) at different functional areas including residential area (RA), industrial area (IA), suburb (SB), roadside (ST) and Botanical Garden Park (BG). The fraction, bioavailability and health risk of As in the PM₂.₅ samples were investigated and compared between these two years. Arsenic was mainly distributed in the non-specifically sorbed fraction (F1) and the residual fraction (F5). However, the proportion of F1 to the total As in 2017 was higher than that in 2016, while the proportion of As in the amorphous and poorly-crystalline hydrous oxides of Fe and Al fraction (F3) in 2017 was lower. The distributions of fraction and bioavailability showed temporal and spatial characteristics. The total concentration and bioavailability of As in SB and IA were significantly higher than those in RA, ST and BG. The BF (Bioavailability Factor) values of As ranged from 0.30 to 0.61. Health risk assessment indicated that the hazard quotient (HQ) and carcinogenic risk (CR) of As in PM₂.₅ significantly decreased after coal-gas replacement.

This study assessed the sources, magnitudes, and chemical compositions of household air pollution (HAP) and personal exposure in traditional Tibetan households. We measured 24-h personal exposures to PM₂.₅ and kitchen area black carbon (BC) concentrations, using MicroPEMs and microAeths, respectively. Particulate polycyclic aromatic hydrocarbon (PAH) and inorganic element concentrations were quantified via post analyses of a subset of MicroPEM sample filters. Household surveys regarding participant demographics, cookstove usage, household fuel, cooking behaviors, and lifestyles were collected. The results reaffirm that burning firewood and yak dung, mainly for cooking, leads to high PM₂.₅ and BC exposures. The geometric mean concentration (95% confidence interval, CI) was 74.3 (53.6, 103) μg/m³ for PM₂.₅ and the arithmetic mean ± standard deviation (SD) concentration was 4.90 ± 5.01 μg/m³ for BC and 292 ± 364 ng/m³ for 15 identified PAHs, respectively. The arithmetic mean ± SD of mass concentrations of 24 detected elements ranged from 0.76 ± 0.91 ng/m³ (Co) to 1.31 ± 1.35 μg/m³ (Si). Our statistical analyses further illustrated that the high concentrations of PM₂.₅, BC, and most PAHs and metals, are significantly associated with nomadic village, poorer stove/chimney conditions and yak dung burning. The results from this study show that substantial HAP exposure is prevalent in Tibetan households and requires immediate actions to mitigate potential negative environmental health impacts. The observational data also revealed the possibility of other important sources (e.g. traffic and garbage burning) that have contributed to personal exposures. These findings improve our understanding of HAP exposure and potential health risks in Tibetan communities and will help inform strategies for reducing HAP in Tibetan households and beyond.

The arsenic concentration is an important issue in compost production. The main inputs of a compost factory, including kerbsides, green wastes, food industry wastes, and river weeds are investigated in this study. Also, this study investigated how treated timbers, ashes, and other contamination can impact arsenic concentration in compost production. The results showed that most treated timbers and all ashes of treated and untreated timbers contained significant amounts of arsenic. These results revealed that the presence of a small amount of treated timber ashes can significantly increase the arsenic concentration in composts. The results of the study show the arsenic concentration in compost increase during cold months, and it dropped during summer, which would be mostly because of high arsenic concentration in ashes of log burners. This study shows ashes of burning timbers can impact arsenic contamination mostly because of using Copper-Chrome-Arsenic wood preservatives (CCA). Also, the lab results show the arsenic level even in ashes of untreated timber is around 96 ppm. The ashes of H3, H4, and H5 treated timbers contain approximately 133,000, 155,000, and 179,000 ppm of arsenic, which one kg of them can increase arsenic concentration around 10 ppm in 13.3, 15.5 and 17.9 tons of dry compost products. The main problem is many people look at ashes and treated timber as organic materials; however, ashes of treated and untreated timbers contained high concentrations of arsenic. Therefore, it was necessary to warn people about the dangers of putting any ashes in organic waste bins.

The contamination of ground water with arsenic is a great public health concern. This paper discusses the possible formation mechanism of high As groundwater; identify the main influences of natural and anthropogenic factors on As occurrence in groundwater; and finally estimates As-induced potential health hazards in an intensive agricultural region, Datong Basin (Northern China). Our findings indicate that the predominant controlling factors of As in groundwater can be divided into natural factors and anthropogenic activities. Natural factors can be classified as natural potential source of As, environmental geological characteristics and hydrochemical conditions; anthropogenic activities are manifested in industrial coal mining, domestic coal burning, agricultural irrigation return flow and excessive application of fertilizers, and groundwater exploitation. Microbial and/or chemical reduction desorption of arsenate from Fe-oxide/hydroxide and/or clay minerals, As-bearing Fe-oxide/hydroxide reduction coupled with sulfate reduction, and competition with phosphorus are postulated to be the major process dominating As enrichment in the alkaline and anoxic groundwater. In addition, age-dependent human health risk assessment (HHRS) was performed, and high risk values reveal a high toxic and carcinogenic risk of As contaminate for population who is subject to the continuous and chronic exposure to elevated As.

Natural sources, such as soil and wind-erosion dust (SWD), biomass open burning (BOB), sea salt spray (SSAS) and biogenic source (BIO), are major contributors to atmospheric emissions of trace elements (TEs) globally. In this study, we used a comprehensive approach to account for area-, production- and biofuel consumption-based emission factor calculation methods, and thus developed an integrated high-resolution emission inventory for 15 types of TEs (As, B, Cd, Co, Cr, Cu, Hg, Mn, Mo, Ni, Pb, Sb, Se, V and Zn) originated from natural sources in China for the year 2015. The results show that national emissions of TEs in 2015 range from 7.45 tons (Hg) to 1, 400 tons (Zn) except for the extremely high emissions of Mn (10, 677 tons). SWD and BIO are identified as the top two source contributors, accounting for approximately 67.7% and 26.1% of the total emissions, respectively. Absolute emissions of TEs from natural sources are high in the Xinjiang, Inner Mongolia and Tibet autonomous regions with large areas of bare soil and desert. However, emission intensity of TEs per unit area in the Southern provinces of China is higher than those in Northern China and Southwestern China, with the Yunnan and Sichuan provinces displaying the highest emission intensity. Our results suggest that controlling SWD can play a significant role in reducing fugitive particulate matter and the associated emissions of TEs from natural sources in China; and desertification control is particularly critical in the Northwest provinces where the majority of deserts are located.

Organobromine compounds comprise between 3 and 8% by weight of WEEE and mainly converted to HBr and Br₂ in the incinerator. However, these compounds, during the cooling of the flue gases, can form the PBDD/Fs in the post-combustion area of the furnace. Due to the many benefits of Oxy-combustion process, our group has developed a fluidised bed incinerator for burning the WEEE and plan to maximise HBr/Br₂ in the flue gas. Experimental results presented in the recent papers show that the combustion of the WEEE particles attains quickly to thermodynamic equilibrium. Thermodynamic modelling can, therefore, predict the concentration of brominated pollutants, particularly HBr, Br₂, HgBr₂, and Br˙ in the flue gas. In this paper, the effect of various parameters for increasing the HBr/Br₂ ratio in the flue gas has been investigated. The model shows that the addition of very small amounts of hydrogen in the post-combustion area can convert Br₂ and Br˙ into HBr.

Cigarette butts (CBs) are the most common littered items in the environment and may contain high amounts of polycyclic aromatic hydrocarbons (PAHs) from incomplete tobacco leave burning. The potential relevance of PAHs stemming from CBs for aquatic systems remain unclear since to date there is no systematic study on PAHs leaching from CBs. Therefore, in this study the leaching concentrations of 16 EPA-PAHs (except benzo(ghi)perylene) in 3 different types of water were measured. The concentrations of ΣPAHs leachates from 4 h to 21 days ranged from 3.9 to 5.7, 3.3–5.5, and 3.0–5.0 μg L⁻¹ for deionized, tap, and river waters, respectively. For all contact times, there were no substantial differences of the leachate concentrations of PAHs among different water types. Lighter PAHs had the highest concentrations among the detected PAHs and they were detected in the leachates already after 4 h. Concentrations of indeno(1,2,3-cd)pyrene, and dibenz(a,h)anthracene were below the limit of detection in all water samples at different contact times. At all contact times naphthalene and fluorene had the highest concentrations among the studied PAHs. Tap and river water samples with addition of sodium azide as chemical preservative contained significantly higher concentration of ΣPAHs. Our leaching data showed that leached concentrations of PAHs exceeded the Water Framework Directive (WFD) standards and considering the number of CBs annually littered this may pose a risk to aquatic organisms and potentially also humans.

In order to avoid the production of sulfates and nitrates in marine diesel engines that burn sulfur-containing fuels, the operating temperature of their high-pressure selective catalytic reduction (HP-SCR) systems should be higher than 320 °C. For marine low-speed diesel engines, only the pre-turbine exhaust gas temperature can meet this requirement under specific conditions, with the main engine modulation method helping to increase the exhaust gas temperature. However, the main engine modulation method brings down the power output and fuel economy of the main engine and causes the matching problem of the turbine and the other devices with the main engine. The original engine model of the marine low-speed diesel engine and the high-pressure SCR system configuration model have been constructed using one-dimensional simulation software. In addition, the performance of the high-pressure SCR system under the conditions of low-sulfur and high-sulfur exhaust gas was thoroughly analyzed. Moreover, the two main engine modulation schemes of the scavenging bypass and the turbine exhaust bypass of the original engine matching with the high-pressure SCR system were studied. The study found that the weighted average value of the NOx under the condition of low-sulfur exhaust gas met with the requirement of the IMO Tier III regulations when the low-speed diesel engine was matched with the high-pressure SCR system. However, the weighted average value of the NOx under the condition of high-sulfur exhaust gas was slightly higher than that required by the IMO Tier III regulation. In addition, the optimal main engine modulation scheme for this low-speed diesel engine was clarified by comparing the effects of the scavenging bypass and the turbine exhaust bypass modulation on the exhaust performance, and the working performance of the original engine. With an opening of 0.4 of the CBV valve under 25% engine load, the weighted average NOx of the original exhaust gas was 3.38 g/(kW·h), the power had decreased by 0.7%, and the fuel consumption had increased by 1.0%. Furthermore, when the EGB valve opening was 0.3, the weighted average value of NOx was 3.31 g/(kW·h), the power had reduced by 2.4% and the fuel consumption had increased by 2.5%. Both modulation scheme methods made the exhaust performance of the original engine meet the requirements of the IMO Tier III emission regulations, but the scavenging bypass modulation scheme had less impact on the original engine’s performance.