Scale generated from the maintenance of equipment contaminated by naturally occurring radioactive materials may contain also chemical components that cause hazardous pollution to human health and the environment. This study spotlights the characterisation of chemical pollutants in scales in relation to home-made comparison samples as no reference material for such waste exists. Analysis by energy dispersive x-ray fluorescence, with accuracy and precision better than 90%, revealed that barium was the most abundant element in scale samples, ranging from 1.4 to 38.2%. The concentrations of the toxic elements such as lead and chromium were as high as 2.5 and 1.2% respectively. Statistically, high correlation was observed between the concentration of Ba and Sr, sample density, radionuclide contents (210Pb and 226Ra) and self-attenuation factor used for the radio-measurements. However, iron showed a reverse correlation. Interpretation of data with regards to the mineralogical components indicated that 226Ra and 210Pb co-precipitated with the insoluble salt Ba0.75Sr0.25SO4. Since both Ba and Sr have high Z, samples of high density (ρ) were accompanied with high values of self-attenuation correction factors (Cf) for the emitted radiation; correlation matrix of Pearson reached 0.935 between ρ and Cf. An attempt to eliminate the effect of the elemental composition and improve gamma measurements of 210Pb activity concentration in scale samples was made, which showed no correction for self-attenuation was needed when sample densities were in the range 1.0–1.4 g cm−3. For denser samples, a mathematical model was developed. Accurate determinations of radionuclide and chemical contents of scale would facilitate future Environmental Impact Assessment for the petroleum industry.

The Yellow River Delta (YRD) is a large region of China with complex pollution sources and a long history of environmental deterioration. Despite this, relatively little data exists on the status of important contaminants of concern in this region. Here, we review the literature on the status of key persistent organic pollutants (POPs) of concern including organochlorine pesticides (OCPs), polycyclic aromatic hydrocarbons (PAHs), and polychlorinated biphenyls (PCBs) in the YRD. Sources, source identification methods, and spatial distribution patterns are presented. Additionally, POPs contamination levels reported in the literature were evaluated against popular regulatory limits worldwide to form a basis for overall environmental health. Our review determined that OCPs in the YRD originated mainly from current pesticide use and past agricultural pesticide application. Sources of PAHs included petrochemical inputs, coal fired plants, and wood combustion. PCB levels were impacted by the petrochemical industry as well as waste disposal of PCB containing equipment. OCPs exhibited a spatial distribution pattern that increased along the urban–rural gradient, while the opposite was seen for PAHs and PCBs. Comparisons of POPs contamination levels in the YRD with popular regulatory limits suggest that the extent of PCB contamination all mediums (sediment, soil, water, and biota) exceeded that of PAHs and OCPs. Overall pollution levels in the YRD seem to be in control; however, levels from heavily polluted point sources raise numerous concerns about the ecological health of the region and require more attention from regulatory authorities.

Washing clothes made from synthetic materials has been identified as a potentially important source of microscopic fibres to the environment. This study examined the release of fibres from polyester, polyester-cotton blend and acrylic fabrics. These fabrics were laundered under various conditions of temperature, detergent and conditioner. Fibres from waste effluent were examined and the mass, abundance and fibre size compared between treatments. Average fibre size ranged between 11.9 and 17.7μm in diameter, and 5.0 and 7.8mm in length. Polyester-cotton fabric consistently shed significantly fewer fibres than either polyester or acrylic. However, fibre release varied according to wash treatment with various complex interactions. We estimate over 700,000 fibres could be released from an average 6kg wash load of acrylic fabric. As fibres have been reported in effluent from sewage treatment plants, our data indicates fibres released by washing of clothing could be an important source of microplastics to aquatic habitats.

The identification of fecal pollution in aquatic ecosystems is one of the requirements to assess the possible risks to human health. In this report, physicochemical parameters, Escherichia coli enumeration and Methanobrevibacter smithii nifH gene quantification were conducted at 13 marine waters in the coastal beaches of Rio de Janeiro, Brazil. The pH, turbidity, dissolved oxygen, temperature, and conductivity, carried out by mobile equipment, revealed varied levels due to specific conditions of the beaches. The bioindicators’ enumerations were done by defined substrate method, conventional, and real-time PCR. Six marine beach sites (46 %) presenting E. coli levels in compliance with Brazilian water quality guidelines (<2500 MPN/100 mL) showed nifH gene between 5.7 × 10⁹ to 9.5 × 10¹¹ copies. L⁻¹ revealing poor correlation between the two approaches. To our knowledge, this is the first inquiry in qPCR using nifH gene as a biomarker of human-specific sources of sewage pollution in marine waters in Brazil. In addition, our data suggests that alternative indicator nifH gene could be used, in combination with other markers, for source tracking studies to measure the quality of marine ecosystems thereby contributing to improved microbial risk assessment.

Separation between primary and secondary sludge treatment could be a valuable solution for sludge management. According to this approach, secondary sludge can be conveniently used in agriculture while primary sludge could be easily dried and incinerated. It follows that some concern may arise from incinerating primary sludge with respect to the current practice to incinerate mixed digested sludge. Incineration of primary and mixed digested municipal sludge was investigated with a lab-scale equipment in terms of emissions of products of incomplete combustion (PICs) during incineration failure modes. PICs can be grouped in three sub-categories, namely aliphatic hydrocarbons (alkanes and alkenes), compounds with a single aromatic ring, and polycyclic aromatic hydrocarbons (PAHs). After-burning temperature was the most important parameter to be controlled in order to minimize emissions of alkanes and alkenes. As for mono-aromatic compounds, benzene and toluene are the most thermally resistant compounds, and in some cases, an after-burning temperature of 1100 °C was not enough to get the complete destruction of benzene leading to a residual emission of 18 mg/kgₛₗᵤdgₑ. PAHs showed an opposite trend with respect to aliphatic and mono-aromatic hydrocarbons being the thermal failure mode the main responsible of PIC emissions. A proper oxygen concentration is more important than elevated temperature thus reflecting the high thermal stability of PAHs. Overall, obtained results, even though obtained under flameless conditions that are different from those of the industrial plants, demonstrated that separation of primary and secondary sludge does not pose any drawbacks or concern regarding primary sludge being disposed of by incineration even though it is more contaminated than mixed digested sludge in terms of organic pollutants.