Photoaging is an important reaction for waste plastics in the aquatic environment and plays a key role in the lifetime of plastics. Nevertheless, when natural photosensitive substances such as nitrate participate in this process, the physiochemical changes in plastics and the corresponding reaction mechanisms are not well-understood. In this work, the photochemical behavior of polyethylene terephthalate (PET) bottles in deionized water and nitrate solution was systematically investigated under ultraviolet (UV) irradiation. The analyses of the surface physicochemical properties of the photoaged PET bottles indicated that, after 20 days of photo-irradiation, the presence of nitrate reduced the contact angle from 69.8 ± 0.9° to 60.0 ± 0.3°, and increased the O/C ratio from 0.23 to 0.32, respectively. The leaching rate of dissolved organic carbon (DOC), which was 0.0193 mg g⁻¹·day⁻¹ in nitrate solution, was twice that of 0.00941 mg g⁻¹·day⁻¹ in deionized water. Furthermore, fluorescence spectroscopy revealed that the increasing DOC had aromatic rings with hydroxyl on the side-chain formed after UV irradiation. The positive effect of nitrate on the degradation of PET bottles was mainly through the generation of hydroxyl radicals that were produced through the photolysis of nitrate. In addition, two-dimensional correlation spectroscopy analysis showed that the chain scission of PET plastics could be initiated by nitrate-induced ·OH attacking the carbon-oxygen bonds instead of forming peroxides with oxygen. This work elucidates the mechanism of photodegradation of plastics that was induced by nitrate and highlights the important role of natural photosensitive substances in the photoaging process of plastics.

In peri-urban critical zones, soil ecosystems are highly affected by increasing urbanization, causing probably an intense interaction between dissolved organic matter (DOM) and heavy metals in soil. Such interaction is critical for understanding the biogeochemical cycles of both organic matter and heavy metals in these zones. However, limited research has reported the correlative distribution of DOM and heavy metals at high seasonal and spatial resolutions in peri-urban critical zones. In this study, 160 soil samples were collected from the farmland and forestland of Zhangxi watershed, in Ningbo, eastern China during spring, summer, fall and winter four seasons. UV–visible absorption and fluorescent spectroscopy were used to explore the optical characteristics of DOM. The results indicated a mixture of exogenous and autogenous sources of DOM in the Zhangxi watershed, while DOM in farmland exhibited a higher degree of aromaticity and humification than that in forestland. Fluorescent results showed that humic acid-like, fulvic acid-like and microbial-derived humic-like fractions were mostly affected by seasons. The distribution of heavy metals was affected mainly by land-use changes and seasons. Correlation analysis between heavy metals and DOM characteristics and components suggested that aromatic and humic substances were more favorable in binding with EDTA extractable Ni, Cu, Zn and Cd. The bioavailable Cd and Pb decreased due to binding with humic fractions, indicating its great effects on the bioavailability of Cd and Pb. Overall, these findings provide an insight into the correlative distributions of DOM and heavy metals in peri-urban areas, thereby highlighting their biogeochemical cycling in the soil environment.

Despite the wide applications of end member mixing analysis (EMMA) for assigning the sources of dissolved organic matter (DOM) in aquatic environment, there was no study attempting to test the applicability of EMMA for predicting environmental reactivity of DOM. This study aimed to explore the feasibility of EMMA, or the concept of ideal mixing behavior of end members, for describing several well-known DOM reactivities using two DOM end member sources (i.e., soil and algae) at varying mixing ratios. The selected DOM reactivities were trihalomethane formation potential (THMFP), mineral adsorption amount, pyrene binding, membrane resistance, and biodegradation potential. Among the tested DOM functions, all were found to follow the ideal mixing behavior, presenting the linear relationships between the source mixing ratios and the tested reactivity with the R² value of >0.80. The ideal mixing behavior of the DOM functions was more pronounced than that based on several spectroscopic indicators derived from UV absorption and fluorescence spectroscopy. This study provided insight into potential applicability and limitation of EMMA approach in monitoring and predicting environmental functions of DOM in aquatic systems where identified DOM sources are mixed and vary dynamically with the mixing ratios.

Fluorescence spectroscopy is a commonly used technique to analyze dissolved organic matter in aquatic environments. Given the high sensitivity and non-destructive analysis, fluorescence has recently been used to study water-soluble organic carbon (WSOC) in atmospheric aerosols, which have substantial abundance, various sources and play an important role in climate change. Yet, current research on WSOC characterization is rather sparse and limited to a few isolated sites, making it challenging to draw fundamental and mechanistic conclusions. Here we presented a review of the fluorescence properties of atmospheric WSOC reported in various field and laboratory studies, to discuss the current advances and limitations of fluorescence applications. We highlighted that photochemical reactions and relevant aging processes have profound impacts on fluorescence properties of atmospheric WSOC, which were previously unnoticed for organic matter in aquatic environments. Furthermore, we discussed the differences in sources and chemical compositions of fluorescent components between the atmosphere and hydrosphere. We concluded that the commonly used fluorescence characteristics derived from aquatic environments may not be applicable as references for atmospheric WSOC. We emphasized that there is a need for more systematic studies on the fluorescence properties of atmospheric WSOC and to establish a more robust reference and dataset for fluorescence studies in atmosphere based on extensive source-specific experiments.

Fulvic acid (FA) significantly influences the bioavailability and fate of heavy metals in environments, while its acid-base characters and metal binding processes are still unclear. Here, spectroscopic techniques combined with multiple models (e.g., NICA-Donnan model) and two-dimensional correlation spectroscopy (2D COS) were applied to explore the proton and copper binding properties of FA sub-fractions (FA3-FA13). The charge densities, average contents of carboxylic and phenolic groups, average dissociation constants pKa1 and pKa2 of sub-fractions ranged 0–16 meq∙g∙C−1, 5.03–9.58 meq∙g∙C−1, 2.52–4.67 meq∙g∙C−1, 4.15–4.33 and 8.52–9.72, respectively. FA sub-fractions had a relatively narrow distribution of carboxyl group and a broad distribution of phenolic group. FA sub-fractions also exhibited roughly two phenolic hydroxyl groups per every 1–3 phenyl rings. Differential absorbance spectra (DAS) derived Gaussian bands were associated to the inter-chromophore interactions, the changes of molecular conformations and functional groups with copper addition. Differential spectra slopes (DSlope275-295&325-375) were more significant with higher copper concentration and copper amounts bonded to carboxylic groups. UV–Vis and fluorescence spectra with 2D heterospectral COS revealed the copper binding heterogeneities and sequential orders of chromophores and fluorophores, quantitatively confirming by the order of conditional stability constants (log KCu: 4.64–5.56). Salicylic-/polyhydroxyphenolic, hydroxyl and amino groups were strongly associated to the basic units for fluorophores. Sequential changes followed the order of humic-like→fulvic-like materials for FA3/FA5, humic-like→fulvic-like→tryptophan-like materials for FA7, and humic-like→tryptophan-like→fulvic-like→tyrosine-like materials for FA9/FA13. Spectroscopic techniques combined with various models (especially for 2D COS) are beneficial to elucidate the binding heterogeneity and sensitivity for metal-organic matters at the functional group level.

Supported carbon quantum dots (CQDs), used as fluorescent sensors for the detection of metal ions, have rarely been used to remove heavy metals from water. Nitrogen-doped CQDs immobilized in hydrophilic silica hydrogels exhibited a more superior sensitivity and selectivity for the detection of Re(VII) and Cr(VI) than other metal ions, including Fe(III), Fe(II), Zn(II), Cu(II) and Mn(II). For the first time, low limits of detection (LOD) of 2.3 μM for Re(VII) detection and 65 nM for Cr(VI) detection were reported by a facile method. Based on the high selectivity of fluorescent silica hydrogels for Re(VII) and Cr(VI) detection, the removal of Re(VII) and Cr(VI) by graphene oxide (GO) in water was monitored with the hydrogels used as a turn-off fluorescent sensing platform. The consistent results of the sorption isotherms of each metal on GO, which were obtained from the fluorescence spectra and by UV absorption, further verified the possibility of monitoring metal removal by fluorescence detection. Remarkably, GO removed 1186 mg/g of Re(VII) but only 178 mg/g of Cr(VI). The density functional theory (DFT) calculations indicated that both Re(VII) and Cr(VI) formed stable bonds with silica hydrogels, confirming that the interactions between the metal ions and the substrate would promote the fluorescence quenching of the supported CQDs. On the other hand, Re(VII) interacted more strongly with the carboxyl groups of GO than Cr(VI). In addition, a real-time detection system was designed to alarm the service life of a GO filter used for Re(VII) removal.

Widely used titanium dioxide (TiO2) nanoparticles are likely to accumulate ultimately in sediments and potentially pose a risk to water ecosystems. This study evaluated the effect of TiO2 nanoparticles on the photodissolution of particulate organic matter (POM) through fluorescence spectroscopy. Excitation-emission matrices and parallel factor analyses revealed that the fluorescent characteristics of produced dissolved organic matter (DOM) during photodissolution of suspended sediment and synthetic particulate organic matter (SPOM) were primarily humic-like. SPOM particles appeared to simulate well the photodissolution of suspended sediment. Quasi-complete increases in fluorescence intensity and chromophoric DOM (CDOM) abundance were reached after 90, 60, and 50 min irradiation for TiO2 concentrations of 0, 2, and 5 mg L−1, respectively. The faster increment of fluorescence intensity and CDOM abundance indicated the photocatalytic dissolution of SPOM, as opposite charges between TiO2 and SPOM at pH = 4 favored the adsorption of TiO2 onto SPOM. For sediments, the CDOM abundance and fluorescence intensity decreased with increasing TiO2 concentration, resulting from the photocatalytic degradation of photoproduced DOM from sediments. These results demonstrated that pH plays an important role in the photocatalytic dissolution of POM by TiO2. Therefore, appropriate pH controls should be implemented when TiO2 are used to treat sediments contaminated with organic pollutants. Finally, with increasing use of TiO2, its accumulation in sediments may affect the fate of carbon, nutrients, and heavy metals in shallow-water ecosystems.

The number of products containing engineered nanomaterials (ENMs) has increased due to their high industrial relevance as well as their use in diverse consumer products. At the end of their life cycle ENMs might be released to the environment and therefore concerns arise regarding their environmental impact. In order to track their fate upon disposal, it is crucial to establish methods to trace ENMs in complex environmental samples and to differentiate them from naturally-occurring nanoparticles. The goal of this study was to distinctively trace ENMs by (non-invasive) detection methods. For this, fluorescent ENMs, namely quantum dots (QDs), were distinctively traced in complex aqueous matrices, and were still detectable after a period of two months using fluorescence spectroscopy. In particular, two water-dispersible QD-species, namely CdTe/CdS QDs with N-acetyl-l-cysteine as capping agent (NAC-QDs) and surfactant-stabilized CdSe/ZnS QDs (Brij®58-QDs), were synthesized to examine their environmental fate during disposal as well as their potential interaction with naturally-occurring substances present in landfill leachates. When QDs were spiked into a leachate from an old landfill site, alteration processes, such as sorption, aggregation, agglomeration, and interactions with dissolved organic carbon (DOC), led to modifications of the optical properties of QDs. The spectral signatures of NAC-QDs deteriorated depending on residence time and storage temperature, while Brij®58-QDs retained their photoluminescence fingerprints, indicating their high colloidal stability. The observed change in photoluminescence intensity was mainly caused by DOC-interaction and association with complexing agents, such as fulvic or humic acids, typically present in mature landfill leachates. For both QD-species, the results also indicated that pH of the leachate had no significant impact on their optical properties. As a result, the unique spectroscopic fingerprints of QDs, specifically surfactant-stabilized QDs, allowed distinctive tracing in complex aqueous waste matrices in order to study their long-term behavior and ultimate fate.

In this work, two deep subsurface wastewater infiltration systems (SWISs) were constructed and fed with domestic sewage (control system, S1) and mixed wastewater consisting of old landfill leachate and domestic sewage (experimental system, S2). S1 and S2 exhibited favorable removal efficiencies, with TP (98.8%, 98.7%), COD (87.6%, 86.9%), NH₄⁺-N (99.8%, 99.9%) and TN (99.2%, 98.9%). Even when increasing the pollutant load in S2 by adding old landfill leachate, the almost complete removal performance could be maintained in terms of low effluent concentrations and even increased in terms of load removal capabilities, which included COD (19.4, 25.9 g∙m⁻²·d⁻¹), NH₄⁺-N (8.2, 19.9 g∙m⁻²·d⁻¹), TN (8.9, 20.6 g∙m⁻²·d⁻¹). To investigate the transformation of dissolved organic matter along depth, Three-Dimensional Excitation Emission Matrix fluorescence spectroscopy combined with Fluorescence Regional Integration analysis was applied. The results showed that PⅠ,ₙ and PⅡ,ₙ (the proportions of biodegradable fractions) increased gradually from 6.59% to 21.8% at S2_20 to 10.8% and 27.7% at S2_110, but PⅢ,ₙ and PⅤ,ₙ (the proportions of refractory organics) declined from 23.1% to 27.8% at S2_20 to 21.1% and 16.4% at S2_110, respectively. In addition, high-throughput sequencing technology was employed to observe the bacterial community at different depths, and the predicted functional potential of the bacterial community was analyzed by PICRUSt. The results showed that the genera Flavobacterium, Pseudomonas, Vogesella, Acinetobacter and Aquabacterium might be responsible for refractory organic degradation and that their products might serve as the carbon source for denitrifiers to achieve simultaneous nitrate and refractory organic removal. PICRUSt further demonstrated that there was a mutual response between refractory organic degradation and denitrification. Overall, the combined treatment of domestic sewage and old leachate in rural areas by SWIS is a promising approach to achieve comprehensive treatment.

Exposure to methylmercury (MeHg) through fish is a global public health problem. Exposure monitoring is essential for health risk assessment, especially in pregnant women and children due to the documented neurotoxicity. Herein, we evaluate a time series of MeHg exposure via fish in primiparous Swedish women, covering a time period of 23 years (1996–2019). The 655 included mothers were part of the POPUP study (Persistent Organic Pollutants in Uppsala Primiparas) conducted by the Swedish Food Agency (SFA). MeHg exposure was assessed via measurements of total mercury (Hg) in hair using either cold vapor atomic fluorescence spectrophotometry or inductively coupled plasma mass spectrometry, showing very good linear agreement (R² = 0.97). Maternal characteristics and fish consumption were obtained via questionnaires. The median concentration of total Hg in hair was 0.38 mg/kg (range 0.17–1.5) in 1996 and 0.25 mg/kg (range 0.03–1.1) in 2019. On average the women consumed 11 ± 8.2 meals of fish per month, and fish consumption was positively correlated with total Hg in hair (Spearman correlation: 0.39; p < 0.001). In multiple regression analyses, the geometric mean annual decrease of total Hg in hair was −2.5% (95% CI: -3.2, −1.8%). Total fish consumption increased up to 2011 (B: 0.32 times/month per year; 95% CI 0.17, 0.46) after which it started to decline (B: -0.66 times/month per year; 95% CI -0.92, −0.40). Moreover, both total Hg in hair and fish consumption was positively associated with maternal age and education, and inversely associated with pre-pregnancy BMI. In conclusion, the exposure to MeHg via fish appears to be slowly declining among Swedish pregnant women.