Pyrolysis bio-oil was used to partially substitute for phenol in reacting with formaldehyde for the production of bio-oil phenol formaldehyde plywood (BPFP) panels, with the phenol substitution ratio being 20%, 40%, or 60%. Emissions of formaldehyde and volatile organic compounds (VOCs) from the BPFP panels were studied using solid-phase micro-extraction (SPME) followed by headspace gas chromatography/mass spectrometry (GC/MS), and were compared to those from the phenol formaldehyde plywood (PFP) panels. The sources for VOCs were analyzed, and the health risks associated with the BPFP were examined. Results showed that at 80 °C: (1) Formaldehyde emissions from the BPFP panels were increased to about 4 times that of PFP; (2) VOCs emissions were significantly reduced by up to 84.9% mainly due to the greatly reduced phenol emissions, although the total number of VOCs was increased from 20 to 35; (3) BPFP presents greatly increased carcinogenic and non-carcinogenic health risks because of its much stronger emissions of formaldehyde, N,N-dimethylformamide, benzofuran, furfural, and many chemicals from the bio-oil. It is highly advisable that the health risks are properly taken care of before the wide application of BPFP, or similar bio-oil based engineered wood products.

Norfloxacin (NOR) is a persistent organic pollutant and can be effectively removed from effluent by adsorption of biochar. However, the presence of other emerging contaminants, such as surfactants, will potentially alter adsorption performance of norfloxacin by biochar and the molecular-scale mechanisms of the interaction between surfactants and biochar remain poorly understood. In this study, adsorption of norfloxacin on magnetic biochar prepared with iron-containing furfural residue (FRMB) in the presence or absence of anionic surfactants was investigated. The adsorption of NOR was significantly affected by the initial pH and anionic surfactants-sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS). In the presence of SDS and SDBS, the maximum sorption capacities of NOR were 2.33 and 1.97 times higher than that in the absence of surfactants, reached to 698.6 mg g⁻¹ and 589.9 mg g⁻¹, respectively. The optimal pH condition which was 4 indicated that electrostatic adsorption played a decisive role in the adsorption process after introduction of SDS/SDBS. The adsorption data were fitted well by the Elovich model and Freundlich model at the optimal conditions in which both SDS and SDBS were hemimicelle (0.8 mM SDS or 0.4 mM SDBS), indicating surface heterogeneity of FRMB and the adsorption mechanism was related to the assembly of surfactants on biochar. FTIR results showed that FRMB and SDS/SDBS interacted through hydrophobic action, and more complex or aggregates were formed between the NOR and biochar/SDS/SDBS. This work highlights the synergistic enhancement effects of tested surfactants on the removal of NOR by magnetic biochar from aqueous systems.

The botanical substances constitute valuable alternatives to synthetic insecticides. In the last decades, numerous substances of natural origin have been tested against stored-product insects, mostly as fumigants or for contact toxicity, while there is limited knowledge on the efficacy of plant secondary metabolites if used as grain protectants. In the present study, we evaluated the lethal activity of 2-undecanone, acetic acid, trans-anethole, furfural, (E)-2-decenal and (E, E)-2,4-decadienal as wheat protectants for the management of larvae and adults of two important storage pests, Tenebrio molitor (Coleoptera: Tenebrionidae) and Trogoderma granarium (Coleoptera: Dermestidae). 2-undecanone caused 98.9% mortality to the exposed T. molitor adults at 1000 μl/kg wheat 7 days post-exposure, while acetic acid and furfural followed providing 94.4% and 92.2% mortality respectively. 2-Undecanone and (E)-2-decenal caused the highest mortalities to T. molitor larvae (i.e., 87.8% and 80.0% respectively) exposed to 1000 μl/kg wheat for 7 days. All T. granarium adults were dead at 1000 μl (E)-2-decenal or acetic acid/kg wheat 5 or 7 days post-exposure respectively. Complete (100%) mortality was assessed for larvae exposed to (E, E)-2,4-decadienal and (E)-2-decenal at 1000 μl/kg wheat after 4 and 6 days respectively. Our findings report for the first time that 2-undecanone, (E)-2-decenal, and (E, E)-2,4-decadienal are effective new candidate control agents of different developmental stages of T. molitor and T. granarium.

Biochars from Chinese medicine material residues and furfural residues at 300–600 °C (MBC300–MBC600 and FBC300–FBC600) were used as adsorbents for removing tetracycline (TC) from water. The influence of pH and co-existing of cations or low molecular weight organic acids (LMWOAs) was investigated on TC adsorption. Further, the bulk biochars were treated by ball milling into sub-micron particles, and their properties and adsorption performance toward TC were also characterized. For pristine biochars, TC adsorption was nonlinear and heterogeneous. Heterogeneity of biochars resulted in multiple sorption mechanisms, including H-bonding, π-π interaction, and pore filling. FBC300 and FBC600 had maximum sorption at pH 5–7. Electrostatic repulsion of positively charged biochar surfaces with TCH₃⁺ at pH < 3 or negatively charged biochar surfaces with TCH⁻ and/or TC²⁻ at pH > 7 was not favorable for TC removal. TC sorption decreased with increasing Na⁺ concentrations from 0 to 0.1 mol/L, and bivalent cations (Ca²⁺ and Mg²⁺) showed greater inhibiting effect relative to monovalent ones (Na⁺ and K⁺). The LMWOAs could combine with co-existing cations, thus reducing the inhibitory effect of cations and improving TC sorption. The ball milling caused remarkable size reduction of biochar particles, thus exposing more active surfaces to capture more TC molecules from water. This study provided low-cost and high-efficiency biochar absorbents to remove antibiotics from water and will benefit for understanding the relationship between TC sorption characteristics/mechanisms and biochar properties.

Three-dimensional carbon aerogel (CA800) was prepared from waste corrugated cardboard (WCC) by the procedure of slurrying, solvent replacement, drying, and carbonization in turn, and the product was explored as an all-in-one evaporator for solar steam generation without bulk water. Carbonization of the precursor was investigated using thermogravimetric analyzer coupled with Fourier transform infrared spectrometer. Results showed that CO₂, CO, furfural, and levoglucosan were released during pyrolysis of WCC within the range of 300 to 390 °C, while polymerization of newly formed char between 390 and 580 °C mainly resulted in the formation of CO₂ and CO. Both pyrolysis and polymerization reactions can be described by diffusion-controlled mechanisms, and the activation energies were 155.62 and 11.17 kJ mol⁻¹, respectively. CA800 possessed a BET surface area of 210 m² g⁻¹. Light can be effectively absorbed and converted into heat by CA800, and its surface temperature achieving 73 °C under 1 kW m⁻² irradiation. CA800 had outstanding wettability due to the presence of hydrophilic minerals in carbon matrix, and it was able to store as much as 15 times its own weight in water due to its abundant interconnected channels and hierarchical nanopores. Solar-driven water evaporation rate over CA800 achieved 1.72 kg m⁻² (normalized to projection area), which was nearly 6 times higher than the value achieved by the bare water system. The photothermal conversion efficiency was calculated to be 118 %, and the overestimated efficiency was caused by the environmental energy gained by the cold evaporation surface of CA800.

The main purpose of this study was to understand the effect of time and temperature during the hydrothermal carbonisation (HTC) of olive stones (OS). For that purpose, the severity factor was introduced, by which the effect of the HTC conditions on the resultant products could be described. HTC was carried out at various temperatures (160, 180, 200, 220 and 240 °C) and times (3, 6, 12, 24 and 48 h) for producing 25 hydrochars. The yield to hydrochar varied from 70 to 50%. Hydrochars were all submitted to thermogravimetric and elemental analysis. The liquid fractions were also recovered and analysed in order to valorise OS as completely as possible. Thus, highly added-value products such as furfural and 5-hydroxymethylfurfural were detected. At the highest temperature and time, the hydrochar elemental composition was similar to that of lignite coals. Hydrochars were further carbonised at 900 °C, leading to materials with surface areas as high as 1200 m² g⁻¹ and with narrow pore size distributions centred on 0.5 nm. The severity factor allowed finding clear tendencies in the production of hydrochars and derived carbons in terms of yield, composition, and surface area, which would have been hardly analysed if the effects of temperature and time had to be considered separately. We proved that the severity factor, which use is quite uncommon in studies dealing with materials production, is a valuable tool for studying the effects of HTC experimental conditions.

Furanic and phenolic compounds are problematic compounds resulting from the pretreatment of lignocellulosic biomass for biofuel production. Microbial electrolysis cell (MEC) is a promising technology to convert furanic and phenolic compounds to renewable H₂. The objective of the research presented here was to elucidate the processes and electron equivalents flow during the conversion of two furanic (furfural, FF; 5-hydroxymethyl furfural, HMF) and three phenolic (syringic acid, SA; vanillic acid, VA; 4-hydroxybenzoic acid, HBA) compounds in the MEC bioanode. Cyclic voltammograms of the bioanode demonstrated that purely electrochemical reactions in the biofilm attached to the electrode were negligible. Instead, microbial reactions related to the biotransformation of the five parent compounds (i.e., fermentation followed by exoelectrogenesis) were the primary processes resulting in the electron equivalents flow in the MEC bioanode. A mass-based framework of substrate utilization and electron flow was developed to quantify the distribution of the electron equivalents among the bioanode processes, including biomass growth for each of the five parent compounds. Using input parameters of anode efficiency and biomass observed yield coefficients, it was estimated that more than 50% of the SA, FF, and HMF electron equivalents were converted to current. In contrast, only 12 and 9% of VA and HBA electron equivalents, respectively, resulted in current production, while 76 and 79% remained as fermentation end products not further utilized in exoelectrogenesis. For all five compounds, it was estimated that 10% of the initially added electron equivalents were used for fermentative biomass synthesis, while 2 to 13% were used for exoelectrogenic biomass synthesis. The proposed mass-based framework provides a foundation for the simulation of bioanode processes to guide the optimization of MECs converting biomass-derived waste streams to renewable H₂.

Olive stones (OS) were submitted to hydrothermal carbonisation (HTC) in order to evaluate the possibility of producing high added-value products, mainly furfural (FU) and 5-hydroxymethylfurfural (5-HMF) on one hand and hydrochars and carbons on the other hand. Temperature (160–240 °C), residence time (1–8 h), initial pH (1–5.5) and liquid/solid ratio (4–48 w/w) were systematically varied in order to study the main products and to optimise FU production. FU production yield up to 19.9 %, based on the hemicellulose content, was obtained. Other minor, but valuable, compounds such as 5-methylfurfural (5-MF) and some phenolic compounds were also produced. The hydrochar was carbonised at 900 °C, and the resultant carbon material was highly ultramicroporous with a peak of pore size distribution centred on 0.5 nm and a surface area as high as 1065 m² g⁻¹, typical of most carbon molecular sieves.

Intensive corn seed production in Northwest of China produced large amounts of furfural residues, which represents higher treatment cost and environmental issue. The broad calcareous soils in the Northwest of China exhibit low organic matter content and high pH, which led to lower fertility and lower productivity. Recycling furfural residues as soil organic and nutrient amendment might be a promising agricultural practice to calcareous soils. A 3-year field study was conducted to evaluate the effects of furfural as a soil amendment on corn seed production on calcareous soil with compared to biogas residues. Soil physical-chemical properties, soil enzyme activities, and soil heavy metal concentrations were assessed in the last year after the last application. Corn yield was determined in each year. Furfural residue amendments significantly decreased soil pH and soil bulk density. Furfural residues combined with commercial fertilizers resulted in the greater cumulative on soil organic matter, total phosphorus, available phosphorus, available potassium, and cation exchange capacity than that of biogas residue. Simultaneously, urease, invertase, catalase, and alkaline phosphatase increased even at the higher furfural application rates. Maize seed yield increased even with lower furfural residue application rates. Furfural residues resulted in lower Zn concentration and higher Cd concentration than that of biogas residues. Amendment of furfural residues led to higher soil electrical conductivity (EC) than that of biogas residues. The addition of furfural residues to maize seed production may be considered to be a good strategy for recycling the waste, converting it into a potential resource as organic amendment in arid and semi-arid calcareous soils, and may help to reduce the use of mineral chemical fertilizers in these soils. However, the impact of its application on soil health needs to be established in long-term basis.