INTRODUCTION: The Cu polyester thin-sputtered layers on textile fabrics show an acceptable bacterial inactivation kinetics using sputtering methods. MATERIALS AND METHODS: Direct current magnetron sputtering (DCMS) for 40 s of Cu on cotton inactivated Escherichia coli within 30 min under visible light and within 120 min in the dark. For a longer DCMS time of 180 s, the Cu content was 0.294% w/w, but the bacterial inactivation kinetics under light was observed within 30 min, as was the case for the 40-s sputtered sample. RESULTS AND DISCUSSION: This observation suggests that Cu ionic species play a key role in the E. coli inactivation and these species were further identified by X-ray photoelectron spectroscopy (XPS). The 40-s sputtered samples present the highest amount of Cu sites held in exposed positions interacting on the cotton with E. coli. Cu DC magnetron sputtering leads to thin metallic semi-transparent gray–brown Cu coating composed by Cu nanoparticulate in the nanometer range as found by electron microscopy (EM). Cu cotton fabrics were also functionalized by bipolar asymmetric DCMSP. CONCLUSION: Sputtering by DCMS and DCMSP for longer times lead to darker and more compact Cu films as detected by diffuse reflectance spectroscopy and EM. Cu is deposited on the polyester in the form of Cu2O and CuO as quantified by XPS. The redox interfacial reactions during bacterial inactivation involve changes in the Cu oxidation states and in the oxidation intermediates and were followed by XPS. High-power impulse magnetron sputtering (HIPIMS)-sputtered films show a low rugosity indicating that the texture of the Cu nanoparticulate films were smooth. The values of R q and R a were similar before and after the E. coli inactivation providing evidence for the stability of the HIPIMS-deposited Cu films. The Cu loading percentage required in the Cu films sputtered by HIPIMS to inactivate E. coli was about three times lower compared to DCMS films. This indicates a substantial Cu metal savings within the preparation of antibacterial films.

PURPOSE AND METHOD: ZnO/polyaniline nanocomposite in core–shell structure was prepared by the synthesis and adsorption of polyaniline chains on the structure of ZnO nanoparticles. Fourier transform infrared and ultraviolet–visible (UV–Vis) spectroscopy, X-ray diffraction patterns, field emission scanning electron microscopy, and transmission electron microscopy were used to characterize the composition and structure of the nanocomposite. The nanocomposite was used as an active photocatalyst for photodegradation and removal of ampicillin in aqueous solution. RESULTS: UV–Vis spectroscopy studies showed that ZnO/polyaniline nanocomposite absorbs visible light irradiation as well as ultraviolet spectrum, and therefore, it can be photoactivated under visible and ultraviolet lights. The photocatalytic activity of ZnO/polyaniline nanocomposite in degradation of ampicillin molecules in aqueous solution under natural sunlight irradiation was evaluated and compared with that of ZnO nanoparticles and pristine polyaniline. The ZnO/polyaniline core–shell nanocomposite exhibited higher photocatalytic activity compared to ZnO nanoparticles and pristine polyaniline. The effect of operating conditions (pH, ZnO/polyaniline nanocomposite dosage, and ampicillin concentration) in the photocatalytic degradation of ampicillin using ZnO/polyaniline nanocomposite was investigated. The optimum conditions for maximum efficiency of ampicillin degradation under 120 min sunlight irradiation were found as 10 mg L−1 dosage of ZnO/polyaniline nanocomposite, ampicillin concentration of 4.5 mg L−1, and solution pH = 5. Under optimum operating conditions, degradation efficiency was reached to 41% after 120 min of exposure to the sunlight irradiation.

In order to use photocatalysis with solar light, finding more active and especially visible light active photocatalysts is a very important challenge. Also, studies of these photocatalysts should employ a standardized test procedure so that their results can be accurately compared and evaluated with one another. A systematic study of transition metal-modified zinc oxide was conducted to determine whether they are suitable as visible light photocatalysts. The photocatalytic activity of ZnO modified with eight different transition metals (Cu, Co, Fe, Mn, Ni, Ru, Ti, Zr) in three different concentrations (0.01, 0.1, and 1 at.%) was investigated under irradiation with UV as well as with visible light. The employed activity test is the gas-phase degradation of acetaldehyde as described by the ISO standard 22197-2. The results suggest that the UV activity can be improved with almost any modification element and that there exists an optimal modification ratio at about 0.1 at.%. Additionally, Mn- and Ru-modified ZnO display visible light activity. Especially the Ru-modified ZnO is highly active and surpasses the visible light activity of all studied titania standards. These findings suggest that modified zinc oxides may be a viable alternative to titanium dioxide-based catalysts for visible light photocatalysis. Eventually, possible underlying mechanisms are proposed and discussed.