Plastic usage increases year by year, and the growing trend is projected to continue. However as of 2017, only 9% of the 9 billion tons of plastic ever produced had been recycled leaving large amounts of plastics to contaminate the environment, resulting in important negative health and economic impacts. Curbing this trend is a major challenge that requires urgent and multifaceted action. Based on scientific and gray literature mainly published during the last 10 years, this review summarizes key solutions currently in use globally that have the potential to address at scale the plastic and microplastic contaminations from source to sea. They include technologies to control plastics in solid wastes (i.e. mechanical and chemical plastic recycling or incineration), in-stream (i.e. booms and clean-up boats, trash racks, and sea bins), and microplastics (i.e. stormwater, municipal wastewater and drinking water treatment), as well as general policy measures (i.e. measures to support the informal sector, bans, enforcement of levies, voluntary measures, extended producer responsibility, measures to enhance recycling and guidelines, standards and protocols to guide activities and interventions) to reduce use, reuse, and recycle plastics and microplastics in support of the technological options. The review discusses the effectiveness, capital expenditure, and operation and maintenance costs of the different technologies, the cost of implementation of policy measures, and the suitability of each solution under various conditions. This guidance is expected to help policymakers and practitioners address, in a sustainable and cost-efficient way, the plastic and microplastic management problem using technologies and policy instruments suitable in their local context.

Plastic debris incidence in marine environment was already highlighted in the early 1970s. Over the last decade, microplastic pollution in the environment has received increasing attention and is now an emerging research area. Many studies have focused on quantifying microplastic abundance in the marine environment, while there are relatively few data on microplastic occurrence in freshwater environment. Recent studies have reported high concentrations of microplastics in lakes and rivers, although the understanding of several factors influencing source, transport and fate is still limited. This study compares different lakes and the common factors, which could influence the occurrence and distribution of microplastics. The three subalpine lakes monitored include Lake Maggiore, Iseo and Garda. The selected sampling transects reflect the hydrologic conditions, the morphometric characteristics of these lakes, and other factors influencing the release of plastics debris in lakes. Particles of microplastics (<5 mm) were found in all sampled surfaces. The particles collected were classified depending on their number, shape and composition. The shape distribution showed the dominating occurrence of fragments (73.7%). The chemical composition of all examined samples clearly shows dominating presence of polyethylene (45%), polystyrene (18%) and polypropylene (15%). The results provide significant relations among the different contribution of direct and diffuse sources to the quantity of microplastics, highlighting the importance of understanding the spatial distribution dynamics of microplastics within a lake system that acts as a sink and source of plastic particles.

Microplastics (MPs) are an emerging pollutant and a worldwide issue. A wide variety of MPs and tyre wear particles (TWPs) are entering and spreading in the environment. TWPs can reach waterbodies through runoff, where main contributing particulate matter comes from impervious areas. In this paper, TWPs and other types of MPs that were transported with the runoff of a high populated-impervious urban area were characterised. Briefly, MPs were sampled from sediments in a stormwater detention reservoir (SDR) used for flood control of a catchment area of ∼36 km², of which 73% was impervious. The sampled SDR is located in São Paulo, the most populated city in South America. TWPs were the most common type of MPs in this SDR, accounting for 53% of the total MPs; followed by fragments (30%), fibres (9%), films (4%) and pellets (4%). In particular, MPs in the size range 0.1 mm–0.5 mm were mostly TWPs. Such a profile of MPs in the SDR is unlike what is reported in environmental compartments elsewhere. TWPs were found at levels of 2160 units/(kg sediment·km² of impervious area) and 87.8 units/(kg sediment·km street length); MP and TWP loadings are introduced here for the first time. The annual flux of MPs and TWPs were 7.8 × 10¹¹ and 4.1 × 10¹¹ units/(km²·year), respectively, and TWP emissions varied from 43.3 to 205.5 kg/day. SDRs can be sites to intercept MP pollution in urban areas. This study suggests that future research on MP monitoring in urban areas and design should consider both imperviousness and street length as important factors to normalize TWP contribution to urban pollution.

Microplastics are omnipresent in the terrestrial and aquatic environment, and are considered as a potentially serious threat to the biodiversity and ecosystem. Pollution of plastic debris and microplastics in the inland and marine environment has raised concerns in Bangladesh, which is one of the most densely populated countries in the world. This review summarizes the research progress on separation and characterization of microplastics, as well as their occurrence and sources in Bangladesh. Despite of the first total ban on plastic bags in the world introduced back in 2002, microplastics have been ubiquitously detected in the country's inland and marine environment, with the majority of them coming from secondary sources. The microplastics observed in Bangladesh were dominated by fibers, which were derived mainly from textile sources. Polyethylene (PE), polyethylene terephthalate (PET), polypropylene (PP), and polyvinylchloride (PVC) were the most abundant polymers found for microplastics in the marine and freshwater environment of Bangladesh. Along with the identified research priorities to improve the understanding on the ecotoxicological effect and fate of microplastics, extensive and in-depth studies are required to bridge the knowledge gaps to enable comprehensive risk assessment of microplastic pollution on local ecosystems and human health, while effective management of plastic wastes and their recycling are necessary to alleviate this problem in the country.

Synthetic microfibers have been identified as the most prevalent type of microplastic in samples from aquatic, atmospheric, and terrestrial environments across the globe. Apparel washing has shown to be a major source of microfiber pollution. We used California as a case study to estimate the magnitude and fate of microfiber emissions, and to evaluate potential mitigation approaches. First, we quantified synthetic microfiber emissions and fate from apparel washing in California by developing a material flow model which connects California-specific data on synthetic fiber consumption, apparel washing, microfiber generation, and wastewater and biosolid management practices. Next, we used the model to assess the effectiveness of different interventions to reduce microfiber emissions to natural environments. We estimate that in 2019 as much as 2.2 kilotons (kt) of synthetic microfibers were generated by apparel washing in California, a 26% increase since 2008. The majority entered terrestrial environments (1.6 kt), followed by landfills (0.4 kt), waterbodies (0.1 kt), and incineration (0.1 kt). California's wastewater treatment network was estimated to divert 95% of microfibers from waterbodies, mainly to terrestrial environments and primarily via land application of biosolids. Our analysis also reveals that application of biosolids on agricultural lands facilitates a directional flow of microfibers from higher-income urban counties to lower-income rural communities. Without interventions, annual synthetic microfiber emissions to California's natural environments are expected to increase by 17% to 2.1 kt by 2026. Further increasing the microfiber retention efficiency at the wastewater treatment plant would increase emissions to terrestrial environments, which suggests that microfibers should be removed before entering the wastewater system. In our model, full adoption of in-line filters in washing machines decreased annual synthetic microfiber emissions to natural environments by 79% to 0.5 kt and offered the largest reduction of all modeled scenarios.

The aim of the present study was to evaluate “flushable” and “non-flushable” wet wipes as a source of plastic pollution in the River Thames at Hammersmith, London and the impacts they have on the invasive Asian clam, Corbicula fluminea, in this watercourse. Surveys were conducted to assess whether the density of wet wipes along the foreshore upstream of Hammersmith Bridge affected the distribution of C. fluminea. High densities of wet wipes were associated with low numbers of clams and vice versa. The maximum wet wipe density recorded was 143 wipes m⁻² and maximum clam density 151 individuals m⁻². Clams adjacent to the wet wipe reefs were found to contain synthetic polymers including polypropylene (57%), polyethylene (9%), polyallomer (8%), nylon (8%) and polyester (3%). Some of these polymers may have originated from the wet wipe reefs.

Freshwater environments are more sensitive to anthropogenic influences and usually contain higher concentrations of pollutants than marine environments. Microplastic pollution causes additional stress on freshwater animals; yet, studies evaluating the microplastic occurrence in freshwater biota are still limited. In this study, microplastic occurrence in the gastrointestinal tracts (GIT) and gill of commercial fish species (Prussian carp Carassius gibelio (Bloch, 1782); Abu mullet Planiliza abu (Heckel, 1843); Common carp Cyprinus carpio Linnaeus, 1758; European ell Anguilla Anguilla (Linnaeus, 1758); North African catfish Clarias gariepinus (Burchell, 1822); Goldfish Carassius auratus (Linnaeus, 1758) were reported from Orontes River. MPs abundance in the GIT and gill of six species were found as 5.1 ± 2 MPs fish⁻¹ and 4.4 ± 2 MPs fish⁻¹ with an occurrence of 95% and 74%, respectively. The majority of extracted microplastics were fiber, black and less than 1000 μm in size. FTIR analysis determined the main polymer types as polyester (50%), high-density polyethylene (HDPE) (10%), polypropylene (PP) (8%) and polyethylene terephthalate (PET) (5%). High MPs abundance and frequency of occurence indicate the exposure of microplastic pollution in freshwater biota which could threat the health of both individuals and consumers. Results obtained in this study will increase the acknowledgement of MPs pollution in the Orontes River. Also, this study will provide data to the administrators to set up necessary legislations in freshwater ecosystems.

Littoral environments represent the main entry point for pollutants into the sea. Microplastics (MPs) are a growing concern, especially for the Mediterranean basin characterized by densely populated coasts and a semi-enclosed morphology. This article targets MPs associated with a unique coastal habitat - the largest bioconstruction in the Mediterranean (Torre Mileto, Southern Adriatic Sea) built by the reef-building polychaete Sabellaria spinulosa (anellida). We assessed MPs abundance in samples from both bioconstruction and surrounding sediments using stereomicroscopy with UV light and micro-Raman spectroscopy. MPs distribution was analyzed according to substrate (reef vs. sediment), longshore drift (west vs. east side), and reef morphology (hummock vs. platform). Results showed a significantly higher MPs abundance in samples from the western side of the site, potentially related to a longshore drift influence on pollutant distribution. By contrast, no significant differences in MPs abundances were observed in substrates (reefs vs. surrounding sediments) and in reef morphologies (hummock vs. platform), which suggest no direct control of reef-building activity in accumulating MPs. The passive accumulation of MPs, primarily driven by wave action, is likely the main factor explaining the MPs distribution. Micro-Raman Spectroscopy analysis revealed polyethylene terephthalate as the dominant polymer, and fibers as the most abundant morphology; prevalent MPs colors were colorless and black. Data provided here indicate that polychaete reefs temporarily trap MPs, retaining such pollutant in the littoral environment. The mechanism of MPs passive accumulation observed in this study raises questions about the growing risk for this bio-engineered benthic habitats.