The valorization of municipal solid waste incineration bottom and fly ashes (IBA and IFA) as catalysts for thermochemical plastic treatment was investigated. As-received, calcined, and Ni-loaded ashes prepared via hydrothermal synthesis were used as low-cost waste-derived catalysts for in-line upgrading of volatile products from plastic pyrolysis. It was found that both IBA and air pollution control IFA (APC) promote selective production of BTEX compounds (i.e., benzene, toluene, ethylbenzene, and xylenes) without significantly affecting the formation of other gaseous and liquid species. There was insignificant change in the product distribution when electrostatic precipitator IFA (ESP) was used, probably due to the lack of active catalytic species. Calcined APC (C-APC) demonstrated further improvement in the BTEX yield that suggested the potential to enhance the catalytic properties of ashes through pre-treatment. By comparing with the leaching limit values stated in the European Council Decision, 2003/33/EC for the acceptance of hazardous waste at landfills, all the ashes applied remained in the same category after the calcination and pyrolysis processes, except the leaching of Cl⁻ from the ESP, which was around the borderline. Therefore, the use of ashes in catalytic reforming application do not significantly deteriorate their metal leaching behavior. Considering its superior catalytic activity towards BTEX formation, C-APC was loaded with Ni at 15 and 30 wt%. The Ni-loading favored an increase in overall oil yield, while reducing the gas yield when compared to the benchmark Ni loaded ZSM catalyst. However, Ni addition also caused the formation of more heavier hydrocarbons (C20–C35) that would require post-treatment to recover favorable products like BTEX.

Smoke from plastic waste incineration in an open air travels worldwide and is a major source of air pollution particulate matter (PM) that is very withstand to degradation and hazard to human health. Suspension of smoke aerosol components in water occurs during rains and fire extinguishing. Here, water-suspended plastic smoke aerosol (WPS) preparations suitable for biotesting were synthesized. It has been revealed using dynamic light scattering that WPS contained major nano-sized (∼30 nm) PM fraction, and this result was confirmed by electron microscopy. Optical absorption of WPS was in the UV region and an increase in λₑₓ led to a red-shift in fluorescence emission with a corresponding decrease in fluorescence intensity. WPS was analyzed in neurotoxicity studies in vitro using presynaptic rat cortex nerve terminals (synaptosomes). Generation of spontaneous reactive oxygen species (ROS) detected using fluorescent dye 2′,7-dichlorofluorescein in nerve terminals was decreased by WPS (10–50 μg/ml) in a dose-dependent manner. WPS also reduced the H₂O₂-evoked ROS production in synaptosomes, thereby influencing cellular oxidative processes and this effect was similar to that for carbon nanodots. WPS (0.1 mg/ml) decreased the synaptosomal membrane potential and synaptic vesicle acidification in fluorimetric experiments. WPS (1.0 mg/ml) attenuated the synaptosomal transporter-mediated uptake of excitatory and inhibitory neurotransmitters, L-[¹⁴C]glutamate and [³H]GABA, respectively. This can lead to an excessive increase in the glutamate concentration in the synaptic cleft and neurotoxicity via over activation of ionotropic glutamate receptors. Therefore, WPS was neurotoxic and provoked presynaptic malfunction through changes of oxidative activity, reduction of the membrane potential, synaptic vesicle acidification, and transporter-mediated uptake of excitatory and inhibitory neurotransmitters in nerve terminals. In summary, synthesis and emission to the environment of ultrafine PM occur during combustion of plastics, thereby polluting air and water resources, and possibly triggering development of neuropathologies.

Environmentally persistent free radicals (EPFRs) are receiving increasing concern due to their toxicity and ubiquity in the environment. To avoid restrictions imposed when using a high-volume active sampler, this study uses tree leaves to act as passive samplers to investigate the spatial distribution characteristics and sources of airborne EPFRs. Tree leaf samples were collected from 120 sites in five areas around China (each approximately 4 km × 4 km). EPFR concentrations in particles (<2 μm) on the surface of 110 leaf samples were detected, ranging from 7.5 × 10¹⁶ to 4.5 × 10¹⁹ spins/g. For the 10 N.D. samples, they were all collected from areas inaccessible by vehicles. The g-values of EPFRs on 68% leaf samples were larger than 2.004, suggesting the electron localized on the oxygen atom, and they were consistent with the road dust sample (g-value: 2.0042). Significant positive correlation was found between concentrations of elemental carbon (tracer of vehicle emissions) and EPFRs. Spatial distribution mapping showed that EPFR levels in various land uses differed noticeably. Although previous work has linked atmospheric EPFRs to waste incineration, the evidence in this study suggests that vehicle emissions, especially from heavy-duty vehicles, are the main sources. While waste incinerators with low emissions or effective dust-control devices might not be an important EPFR contributor. According to our estimation, over 90% of the EPFRs deposited on tree leaves might be attributed to automotive exhaust emissions, as a synergistic effect of primary exhausts and degradation of aromatic compounds in road dust. With adding the trapping agent into the particle samples (<2 μm), signals of hydroxyl radicals were observed. This indicates that EPFRs collected from this phytosampling method can lead to the release of reactive oxygen species (ROS) once they are inhaled by human beings. Thus, this study helps highlight EPFR “hotspots” for potential health risk identification.

This paper investigated the application of graphite particle electrodes to the removal of Zn, Pb, Cu, and Cd from municipal solid waste incineration (MSWI) fly ashes in a three-dimensional (3D) electrokinetic reactor. The influences of the voltage gradient, mass ratio of graphite powers to fly ashes, nitric acid concentrations, proposing times, and liquid-solid (L-M) ratios on the remedial efficiencies of MSWI fly ashes were comprehensively studied in an orthogonal deign and a sequential double-factor setup. Significant analysis showed that changes in the mass ratios and nitric acid concentrations both had a statistically significant effect on the removals of Zn and Pb. Proposing times and L-M ratios both remarkably affected the removals of heavy metals (HMs) in a 3D electrochemical system. The graphite powers had a narrower distribution interval and slightly larger surface areas compared with MSWI fly ashes, which relented pH gradients over the time in the electrochemical experiments and minimized the bubble barricade caused by the hydrolysis. The particle electrode had increased the residue factions of Zn, Pb, Cu, and Cd in S1 region by approximately 216%, 136%, 309%, and 950%, respectively, compared with the raw MSWI fly ashes. The addition of graphite powders to a two-dimensional (2D) electrochemical process strengthened hydrolysis reactions, shortened time for the redistribution of pH balance, decreased the tortuosity of migration path, and increased the desorption concentrations of HMs in the sample area.

Istanbul, one of the mega cities in the world located between Asia and Europe, has suffered from severe air pollution problems due to rapid population growth, traffic and industry. Atmospheric levels of PAHs and PCBs were investigated in Istanbul at 22 sampling sites during four different sampling periods using PUF disk passive air samplers and spatial and temporal variations of these chemicals were determined. Soil samples were also taken at the air sampling sites. At all sites, the average ambient air Σ15PAH and Σ41PCB concentrations were found as 85.6 ± 68.3 ng m−3 and 246 ± 122 pg m−3, respectively. Phenanthrene and anthracene were the predominant PAHs and low molecular weight congeners dominated the PCBs. The PAH concentrations were higher especially at urban sites close to highways. However, the PCBs showed moderately uniform spatial variations. Except four sites, the PAH concentrations were increased with decreasing temperatures during the sampling period, indicating the contributions of combustion sources for residential heating, while PCB concentrations were mostly increased with the temperature, probably due to enhanced volatilization at higher temperatures from their sources. The results of the Factor Analysis represented the impact of traffic, petroleum, coal/biomass and natural gas combustion and medical waste incineration plants on ambient air concentrations. A similar spatial distribution trend was observed in the soil samples. Fugacity ratio results indicated that the source/sink tendency of soil for PAHs and PCBs depends on their volatility and temperature; soil generally acts as a source for lighter PAHs and PCBs particularly in higher temperatures while atmospheric deposition is a main source for higher molecular weight compounds in local soils. Toxicological effect studies also revealed the severity of air and soil pollution especially in terms of PAHs in Istanbul.

Cities and contaminated areas can be primary or secondary sources of polychlorinated biphenyls (PCBs), dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), and other chemicals, into air and soil and can influence the regional level of some of these pollutants. In a contaminated site, the evaluation of such emissions can be crucial in the choice of the remediation technology to be adopted. In the city of Brescia (Northern Italy), more than 100 ha of agricultural areas were contaminated with PCBs, PCDD/Fs and heavy metals, originating from the activities of a former PCB factory. In order to evaluate the current emissions of PCBs and PCDD/Fs from the contaminated site, in a location where other current sources are present, we compared measured and predicted air concentrations, resulting from chemical volatilization from soils as well as fingerprints of Brescia soils and of soils contaminated by specific sources. The results confirm that the contaminated area is still a current and important secondary source of PCBs to the air, and to a lesser extent of PCDFs (especially the more volatile), but not for PCDDs. PCBs in soils have fingerprints similar to highly chlorinated mixtures, indicating contamination by these mixtures and/or a long weathering process. PCB 209 is also present at important levels. PCDD fingerprints in soil cannot be related to current emission sources, while PCDFs are compatible to industrial and municipal waste incineration, although weathering and/or natural attenuation may have played a role in modifying such soil fingerprints. Finally, we combined chemical and microbiological analyses to provide an integrated approach to evaluate soil fingerprints and their variation in a wider perspective, which accounts for the mutual effects between contamination and soil microbiota, a pivotal hint for addressing in situ bioremediation activities.

Incineration has gradually become the most effective way to deal with MSW due to its obvious volume reduction and weight reduction effects. However, since heavy metals and organic pollutants carried by municipal solid waste incinerator fly ash (MSWI FA) pose a serious threat to the ecological environment and human health, they need to be handled carefully. In this study, the current status of MSWI FA disposal was first reviewed, and the harmless and resourceful disposal technologies of heavy metals and organic pollutants in MSWI FA are summarized as well. A summary of the advantages and disadvantages of each technology, including sintering, melting/vitrification, hydrothermal treatment, mechanochemistry, solidification/stabilization of MSWI FA, is compared. Finally, the research work that needs to be strengthened in the future (such as codisposal of multiple wastes, long-term stability research of disposal products, etc.) was proposed. Through comprehensive analysis, some reasonable and feasible suggestions were provided for the effective and safe disposal of MSWI FA in the future.

Raman imaging can effectively characterise microplastics and nanoplastics, which is validated here to capture the items released from the plastic gloves when subjected to a mimicked fire. During the COVID-19 pandemic, large quantities of personal protective equipment (PPE) units have been used, such as the disposable gloves. If discarded and poorly managed, plastics gloves might break down to release secondary contaminants. The breakdown process can be accelerated by burning in a bushfire or at the incineration plants. During the burning process, the functional groups on the surface can be burned differently due to their different thermal stabilities. The different degrees of burning can be distinguished and visualised via Raman imaging. In the meantime, at the bottom of the burned plastics, microplastics and nanoplastics can be generated at a significant amount. The possible false Raman imaging on microplastics and nanoplastics is also discussed, by effectively extracting and distinguishing the weak signal from the background or noise. Overall, these findings confirm the importance of effectively working waste incineration plants and litter prevention, and suggest that Raman imaging is a suitable approach to characterise microplastics and nanoplastics.

As primary anthropogenic emission source of toxic pollutants such as heavy metals and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), municipal solid waste (MSW) incineration has caused worldwide concern. However, a comprehensive analysis of the pollution characteristics and health risks of PCDD/Fs and heavy metals in soils around MSW incineration plants is lacking. In this study, 17 PCDD/Fs and 11 heavy metals in soil samples collected near MSW incineration plants in Sichuan province were investigated to evaluate their pollution characteristics and potential health risk. Sichuan was selected as the study area because the MSW incineration amount in this province ranks first among all inland provinces in China. The PCDD/Fs concentrations ranged from 0.30 to 7.50 ng I-TEQ/kg, which were significantly below risk screening and intervention thresholds. Regarding heavy metals, principal component analysis suggested that Hg, Pb and Zn were the primary metals emitted from the MSW incineration plants. Cluster analysis of PCDD/Fs and heavy metals showed that of PCDD/Fs homologs and heavy metals (e.g., Hg, Pb, Zn and Cd) were clustered into one group, indicating the coexistence and coaccumulation of heavy metals (especially Hg, Pb, Zn, and Cd) and PCDD/Fs in soil. These heavy metals are thus candidate tracers for PCDD/Fs in soil near MSW incineration plants. A health risk analysis found that the carcinogenic and non-carcinogenic risks of PCDD/Fs and heavy metals (except for Ni) in the soil samples were all within acceptable levels. This study provides new insights into correlations and health risks of PCDD/Fs and heavy metals in surface soil near MSW incineration plants. The findings have implications for future studies of environmental and human health risk analysis related to waste incineration.

This study focused on the syngenetic control of polychlorinated-ρ-dibenzodioxins and dibenzofurans (PCDD/Fs) and heavy metals by field stabilization/solidification (S/S) treatment for municipal solid waste incineration fly ash (MSWIFA) and multi-step leachate treatment. Modified European Community Bureau of Reference (BCR) speciation analysis and risk assessment code (RAC) revealed the medium environment risk of Cd and Mn, indicating the necessity of S/S treatment for MSWIFA. S/S treatment significantly declined the mass/toxic concentrations of PCDD/Fs (i.e., from 7.21 to 4.25 μg/kg; from 0.32 to 0.20 μg I-TEQ/kg) and heavy metals in MSWIFA due to chemical fixation and dilution effect. The S/S mechanism of sodium dimethyldithiocarbamate (SDD) and cement was decreasing heavy metals in the mild acid-soluble fraction to reduce their mobility and bioavailability. Oxidation treatment of leachate reduced the PCDD/F concentration from 49.10 to 28.71 pg/L (i.e., from 1.60 to 0.98 pg I-TEQ/L) by suspension absorption or NaClO oxidation decomposition, whereas a so-called “memory effect” phenomena in the subsequent procedures (adsorption, press filtration, flocculating settling, slurry separation, and carbon filtration) increased it back to 38.60 pg/L (1.66 pg I-TEQ/L). Moreover, the multi-step leachate treatment also effectively reduced the concentrations of heavy metals to 1–4 orders of magnitude lower than the national emission standards. Furthermore, the PCDD/Fs and heavy metals in other multiple media (soil, landfill leachate, groundwater, and river water) and their spatial distribution characteristics site were also investigated. No evidence showed any influence of the landfill on the surrounding liquid media. The slightly higher concentration of PCDD/Fs in the soil samples was ascribed to other waste management processes (transportation and unloading) or other local source (hazardous incineration plant). Therefore, proper management of landfills and leachate has a negligible effect on the surrounding environment.