This study presents simultaneous hexavalent chromium (Cr(VI)) reduction and phenol degradation using Stenotrophomonas sp., isolated from tannery effluent contaminated soil. Phenol was used as the sole carbon and energy source for Cr(VI) reduction. The optimization of different operating parameters was done using Placket-Burman design (PBD) and Box-Behnken design (BBD). The significant operating variables identified by PBD were initial Cr(VI) and phenol concentration, pH, temperature, and reaction time. These variables were optimized by a three-level BBD and the optimum initial Cr(VI) concentration, initial phenol concentration, pH, temperature, and reaction time obtained were 16.59 mg/l, 200.05 mg/l, 7.38, 31.96 °C and 4.07 days, respectively. Under the optimum conditions, 81.27 % Cr(VI) reduction and 100 % phenol degradation were observed experimentally. The results concluded that the Stenotrophomonas sp. could be used to decontaminate the effluents containing Cr(VI) and phenol effectively.

This paper demonstrated the relative bactericidal activity of photoirradiated (6W-UV Torch, λ > 340 nm and intensity = 0.64 mW/cm) P25-TiO nanoparticles, nanorods, and nanotubes for the killing of Gram-negative bacterium Agrobacterium tumefaciens LBA4404 for the first time. TiO nanorod (anatase) with length of 70-100 nm and diameter of 10-12 nm, and TiO nanotube with length of 90-110 nm and diameter of 9-11 nm were prepared from P-25 Degussa TiO (size, 30-50 nm) by hydrothermal method and compared their biocidal activity both in aqueous slurry and thin films. The mode of bacterial cell decomposition was analyzed through transmission electron microscopy (TEM), Fourier transform-infrared (FT-IR), and K ion leakage. The antimicrobial activity of photoirradiated TiO of different shapes was found to be in the order P25-TiO > nanorod > nanotube which is reverse to their specific surface area as 54 < 79 < 176 m g, evidencing that the highest activity of P25-TiO nanoparticles is not due to surface area as their crystal structure and surface morphology are entirely different. TiO thin films always exhibited less photoactivity as compared to its aqueous suspension under similar conditions of cell viability test. The changes in the bacterial surface morphology by UV-irradiated P25-TiO nanoparticles was examined by TEM, oxidative degradation of cell components such as proteins, carbohydrates, phospholipids, nucleic acids by FT-IR spectral analysis, and K ion leakage (2.5 ppm as compared to 0.4 ppm for control culture) as a measure of loss in cell membrane permeability.

Ambient concentrations of PM and associated elemental and ionic species were measured over the cold and the warm months of 2010 at an urban and two rural sites located in the lignite-fired power generation area of Megalopolis in Peloponnese, southern Greece. The PM concentrations at the urban site (44.2 ± 33.6 μg m) were significantly higher than those at the rural sites (23.7 ± 20.4 and 22.7 ± 26.9 μg m). Source apportionment of PM and associated components was accomplished by an advanced computational procedure, the robotic chemical mass balance model (RCMB), using chemical profiles for a variety of local fugitive dust sources (power plant fly ash, flue gas desulfurization wet ash, feeding lignite, infertile material from the opencast mines, paved and unpaved road dusts, soil), which were resuspended and sampled through a PM inlet onto filters and then chemically analyzed, as well as of other common sources such as vehicular traffic, residential oil combustion, biomass burning, uncontrolled waste burning, marine aerosol, and secondary aerosol formation. Geological dusts (road/soil dust) were found to be major PM contributors in both the cold and warm periods of the year, with average annual contribution of 32.6 % at the urban site vs. 22.0 and 29.0 % at the rural sites. Secondary aerosol also appeared to be a significant source, contributing 22.1 % at the urban site in comparison to 30.6 and 28.7 % at the rural sites. At all sites, the contribution of biomass burning was most significant in winter (28.2 % at the urban site vs. 14.6 and 24.6 % at the rural sites), whereas vehicular exhaust contribution appeared to be important mostly in the summer (21.9 % at the urban site vs. 11.5 and 10.5 % at the rural sites). The highest contribution of fly ash (33.2 %) was found at the rural site located to the north of the power plants during wintertime, when winds are favorable. In the warm period, the highest contribution of fly ash was found at the rural site located to the south of the power plants, although it was less important (7.2 %). Moderate contributions of fly ash were found at the urban site (5.4 and 2.7 % in the cold and the warm period, respectively). Finally, the mine field was identified as a minor PM source, occasionally contributing with lignite dust and/or deposited wet ash dust under dry summer conditions, with the summertime contributions ranging between 3.1 and 11.0 % among the three sites. The non-parametric bootstrapped potential source contribution function analysis was further applied to localize the regions of sources apportioned by the RCMB. For the majority of sources, source regions appeared as being located within short distances from the sampling sites (within the Peloponnesse Peninsula). More distant Greek areas of the NNE sector also appeared to be source regions for traffic emissions and secondary calcium sulfate dust.

Provincial-level data for population, livestock, land use, economic growth, development of sewage systems, and wastewater treatment rates were used to construct a river nitrogen (N) export model in this paper. Despite uncertainties, our results indicated that river N export to coastal waters increased from 531 to 1,244 kg N km(-2) year(-1) in the Changjiang River basin, 107 to 223 kg N km(-2) year(-1) in the Huanghe River basin, and 412 to 1,219 kg N km(-2) year(-1) in the Zhujiang River basin from 1980 to 2010 as a result of rapid population and economic growth. Significant temporal changes in water N sources showed that as the percentage of runoff from croplands increased, contributions of natural system runoff and rural human and livestock excreta decreased in the three basins from 1980 to 2010. Moreover, the nonpoint source N decreased from 72 to 58 % in the Changjiang River basin, 80 to 67 % in the Huanghe River basin, and 69 to 51 % in the Zhujiang River basin, while the contributions of point sources increased greatly during the same period. Estimated results indicated that the N concentrations in the Changjiang, Huanghe, and Zhujiang rivers during 1980-2004 were higher than those in the St. Lawrence River in Canada and lower than those in the Thames, Donau, Rhine, Seine, and Han rivers during the same period. River N export will reduce by 58, 54, and 57 % for the Changjiang River, Huanghe River, and Zhujiang River in the control scenario in 2050 compared with the basic scenario.

Drinking water treatment residuals (WTRs), nonhazardous by-products generated in a drinking water treatment plant, can be reused to immobilize phosphorus (P) to control the internal P loading from lake sediments for eutrophication control. Reasonably, before practical application, it is essential to determine the P immobilization capability of WTRs in lake sediments under various conditions. In this work, laboratory scale experiments were conducted to investigate the effects of light, microbial activity, and sediment resuspension on the P immobilization capability of WTRs. The results suggested that absence of light, low microbial activity, and sediment resuspension can increase the internal P loading from lake sediments. WTRs can, however, reduce the internal P loading significantly. Further analysis demonstrated that WTRs can stabilize P, decreasing the P bioavailability in the sediments under varied conditions. WTRs also presented little undesirable effects on the dissolved oxygen levels and pH of overlying water. Therefore, light, microbial activity, and sediment resuspension have little effect on the P immobilization capability of WTRs in lake sediments.

This study demonstrates the influences of position, number of nitrogen (N) atoms and –C–N– or –N=N– linkage present in the six membered heterocyclic compounds such as pyridine, pyrazine, and pyridazine on their photocatalytic degradation by Au, Ag, and Fe⁺² deposited TiO₂ photocatalyst. The photodegradation rate of these heterocyclic compounds follow the order pyridine > pyrazine > pyridazine due to the different extent of hydroxylation and difference in position and number of N atoms in the aromatic moiety. The Au photodeposition significantly improved the TiO₂ photoactivity as compared to Ag and Fe⁺² loading. The presence of two N atoms in pyrazine and pyridazine as compared to one N atom in pyridine hamper the nucleophilc attack of OH radicals in comparison to easy hydroxylation of pyridine ring. There is 1 N atom, 4C–C, 1C–N and 1C=N bond in pyridine, 2 N atoms in the 1 and 4 positions, 2C–C, 2C–N bonds and 2C=N bonds in pyrazine, and pyridazine ring contains 2 N atoms in the 1 and 2 positions, 3C–C, 1N–N bond and 2C=N bonds. The bond strength/energy decreases gradually as: C=N– (615 KJ/mol) > –N=N– (418 KJ/mol) > –C–C– (347 KJ/mol) > –C–N– (305 KJ/mol) > –N–N– (163 KJ/mol). As pyridine has 1C–N, 1C=N, and no N–N bond, it photodegrades easily as compared to 1 N–N and 2C=N bonds of pyridazine of lowest photodecomposition rate. The improved photoactivity of Au–TiO₂ is explained on the basis of its favorable redox potential, work function, and electron-capturing capacity, etc.

This paper describes an in-depth analysis to investigate the huge variation in the measured roadside air-pollutant concentrations of carbon monoxide and nitrogen dioxide in terms of the traffic flow levels, the orientation of the street to the prevailing wind, the wind speed, temperature and barometric pressure. The work has attempted to develop generic parameters that can be applied to other urban areas. However, in the absence of a measure of congestion at the site in Palermo (Italy), the methodological approach proposed used the simultaneous noise measurements, in units of decibels (B), to help parameterise a generic congestion indicator in terms of the traffic flow. The potential transferability of the approach was demonstrated for a site in Marylebone Road, London (UK), given the similarity of the two study sites, canyon shape, traffic characteristics and road orientation. The results showed that, within the range of data available, noise levels could be used as a proxy for flow change on the shoulders of the peak hour and hence congestion and a generic relationship with factors statistically significant at 99 % confidence allows roadside concentrations due to traffic to be estimated with a regression coefficient of R (2) = 0.73 (R = 0.85). The research demonstrates that whilst there are indeed underlying relationships that can explain the roadside concentrations based on traffic and meteorological conditions, evidence is presented that confirms the complexity of the physical and chemical processes that govern roadside concentrations.

With the rapid urbanization, the southeast coastal cities of China are facing increasing air pollution in the past decades. Large emissions of VOCs from vehicles and petrochemical factories have contributed greatly to the local air quality deterioration. Investigating the pollution characteristics of VOCs is of great significance to the environmental risk assessment and air quality improvement. Ambient VOC samples were collected simultaneously from nine coastal cities of southeast China using the Tedlar bags, and were subsequently preprocessed and analyzed using a cryogenic preconcentrator and a gas chromatography–mass spectrometry system, respectively. VOC compositions, spatial distributions, seasonal variations and ozone formation potentials (OPFs) were discussed. Results showed that methylene chloride, toluene, isopropyl alcohol and n-hexane were most abundant species, and oxygenated compounds, aromatics and halogenated hydrocarbons were most abundant chemical classes (62.5–95.6 % of TVOCs). Both industrial and vehicular exhausts might contribute greatly to the VOC emissions. The VOC levels in the southeast coastal cities of China were sufficiently high (e.g., 6.5 μg m⁻³ for benzene) to pose a health risk to local people. A more serious pollution state was found in the southern cities of the study region, while higher VOC levels were usually observed in winter. The B/T ratio (0.26 ± 0.09) was lower than the typical ratio (ca. 0.6) for roadside samples, while the B/E (1.6–7.6) and T/E (7.2–26.8) ratios were higher than other cities around the world, which indicated a unique emission profile in the study region. Besides, analysis on ozone formation potentials (OFPs) indicated that toluene was the most important species in ozone production with the accountabilities for total OFPs of 22.6 to 59.6 %.

The performance of two bacteria, Arthrobacter viscosus and Streptococcus equisimilis, and the effect of the interaction of these bacteria with four different clays on the retention of diethylketone were investigated in batch experiments. The uptake, the removal percentages and the kinetics of the processes were determined. S. equisimilis, by itself, had the best performance in terms of removal percentage, for all the initial diethylketone concentrations tested: 200, 350 and 700 mg/L. The uptake values are similar for both bacteria. A possible mechanism to explain the removal of diethylketone includes its degradation by bacteria, followed by the adsorption of the intermediates/sub-products by the functional groups present on the cells' surfaces. The assays performed with bacteria and clays indicated that the uptake values are similar despite of the clay used, for the same microorganism and mass of clay, but in general, higher values are reached when S. equisimilis is used, compared to A. viscosus. Kinetic data were described by pseudo-first- and pseudo-second-order models.

An ordered hierarchical meso/macroporous monoclinic bismuth vanadate (BiVO₄) particle was fabricated for the first time by a simple two-step melamine template hydrothermal method followed by calcination. The physiochemical parameters of as-prepared porous materials were characterized by means of X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, Raman, Barrett–Emmett–Teller, and UV–vis techniques. The nitrogen adsorption–desorption measurement and pore size distribution curve suggest that meso/macropores exist in these hierarchical microarchitectures. Further, it is found that melamine plays a significant role in the formation of porous BiVO₄ particles, and when a known amount of melamine was added, the surface area and pore size of such porous BiVO₄ particles were increased. The photocatalytic activities of the as-prepared hierarchical BiVO₄ samples were measured for the photodegradation of Congo red aqueous dye solution under visible light irradiation. Surprisingly, the porous BiVO₄ particles showed outstanding photocatalytic activities than polycrystalline BiVO₄ sample. The possible enhancement of such catalytic performance has also been further discussed.