This article gives a review of modern networking technologies and standards used in the development of distributed control systems. Study of related scientific and professional literature has been performed, and basing on it a multi-level model of digital network structure in the field of small-scale autonomous combined power systems has been proposed. Necessity of integration of autonomous powering into SmartHouse systems and related distributed computing and networking issues are reflected as well. As there is a wide variety of industrial networking standards used, this review covers and groups more frequently used protocols and stacks from the view of OSI (Open Systems Interconnection) reference model and layers of industrial automation. The aim of this article is to give a reference-point in the development of distributed control systems in the field of small-scale autonomous power supply and integration of them in SmartHouse systems.

By using analytical correlations derived as a result of theoretical research, a computer algorithm has been worked out for simulating the functions of the plough body and the forces exerted by soil upon the operating parts, as well as its draft resistance. These correlations allow to determine the draft resistance of the plough depending on the parameters of its body, as well as to evaluate the impact of the physical and mechanical properties of soil, such as friction upon it. The greatest influence upon the draft resistance is exerted by soil hardness, density and slip resistance along the surfaces of the operating parts. The latter is also affected by soil adhesion, which particularly manifests itself in wet clay soils at lower temperatures. It has been clarified that the friction resistance constitutes 46–62% of the total draft resistance of the plough body. The main ways of lowering the friction resistance and the total draft resistance of the plough are the introduction of a more rational design of its body having optimum parameters, decreasing the resistance of the share-mouldboard surface and the values of reactions of the supporting surfaces, as well as the application of antifriction materials and better modes of joining with tractors.

Lodgepole pine (Pinus contorta) samples from three different provenances in Canada were investigated. All trees were the same age and had been grown in Latvia in similar conditions. Lodgepole pine of Summit Lake provenance had higher wood density (503 kg m-3) and a higher late wood content (46%) in comparison to Fort Nelson and Pink Mountain provenances. Investigation of chemical composition of wood indicated Summit Lake provenance wood as superior in cellulose content (49.7%), but no differences in lignin and extractives content were found between samples. Kraft pulp yield of Summit Lake samples (48%) was the highest, but the handsheet strength properties were relatively higher for pulp from Pink Mountain provenance pine wood.

Latvia uses average moisture content and density indexes obtained in Russia and European countries; though, these indexes are different, and there is no information about the most suitable one for conditions in Latvia. Research complex on Latvia’s industrially important tree species - Scots pine (Pinus sylvestris L.) stemwood and bark moisture and density changes, depending on influencing factors, is being conducted at Forestry Faculty of Latvian University of Agriculture. The research results on Scots pine, obtained during the year 2011 in the whole territory of Latvia, are outlined in this article. Wood and bark moisture and density were analyzed in 21 sampling plots, arranged in middle aged and cutting-aged reached forest stands, depending on tree age, cutting time and location place in the tree stem. The average moisture content of pine wood mostly depends on heartwood specific weight and age of the tree. With an increase of tree age, average wood moisture content value decreases from 111% (40-year-old trees) to 77% (145-year-old trees). Scots pine heartwood moisture content changes a little during the year: 30– 34% for 71 to 146-year-old trees; and 34-41% for 37–70-year-old trees. Sapwood moisture content is changes from 113% (in the summer) to 130% (in the winter), without any reference to the age of the tree. The average density of oven dry timber obtained from 71–146-year-old trees in the research is 0.501 g cmE-3, whereas in freshly cut condition – 0.848 g cmE-3.

Leaf morphology was assessed in Pajiesys and Seirijai field trials of oaks. Oaks in these trials are the progenies of oak trees (Quercus genus) that grow in the Trakas forest of Seirijai district of Alytus forest enterprise of Lithuania. The aim of the study was to determine the number of hybrid trees between the progenies of the Trakas forest in Pajiesys and Seirijai field trials. 251 oaks belonging to 40 half-sib families were sampled. Twenty three leaf morphological variables were measured on each of 5 leaves collected from each tree and analysed by principal component analysis (PCA) and discriminant analysis (DA). The study concluded that Q. robur and Q. petraea leaves are most clearly identified by six morphological traits. Discriminant function of two traits for oak species separation was proposed. The study has also revealed a high degree of interspecific hybridization in field trials. Study results were compared with earlier reports about hybridization occurring in mixed oak stands in other parts of Europe.

When the measurements of power consumed by cutting mechanism electromotor are made, the mechanical cutting power cannot be obtained, because they are different physical processes. However, determination of electricity power is relatively simpler. Therefore, both powers are determined in the study, in order to evaluate coherence between them. Computer numerical control machine was used for climb-sawing of aspen (Populus tremula L.) wood with a circular saw. Mechanical cutting power was calculated from measurements of cutting force, but the electric ones – from measurements of current and voltage. As a result, changes of both powers and of specific cutting work, on what the analytical calculation of cutting power is based, were obtained depending on length of the cutting trajectory. It is found out, that mechanical cutting power is greater than electric power, and it is useful to use for the analytical calculation, based on determination of the specific cutting work, wear coefficient of the cutter that depends not only on the duration of work of cutter, but also on feed speed and the length of the cutting trajectory.

The added value of woodworks is determined by the surface quality because it is the first one seen and evaluated by the client. In the production process it is quite problematic to evaluate woodworks surface quality because of large production capacity, and the processed material can be instrumentally tested with a definite time shift. In production most frequently the surface quality is evaluated visually, which is not quite precise. At the same time during the mechanical processing of wood noise is caused by cutting tools as they gradually wear out. The same reasons influence the increase of noise and the quality of woodwork surface. The essence of the problem is to analyze the registered increase of the noise level at a definite workplace and simultaneously follow the surface quality of the processed material – roughness and wear-out of the cutting instrument. The objective of the paper is to research the method of the noise level data collecting and application in order to evaluate wooden product surface quality during wood processing by milling machines. It would provide an opportunity to update the management processes of massive woodworks, supervise the surface quality of woodworks, reduce costs and increase the added value.

The process of creation of the informative systems based on the account of such animals as horses, sheep and goats is analyzed in the work. Three structural models are created and their comparative analysis is conducted. As a result of analysis the general elements of structures, characteristic to each model were found. The Meta modelling approach to facilitate the system was used. The system has a more abstract structure and allows dynamically to adding not only the animal specimens but also new types of attributes in fly during runtime. Recompilation of the system is not required there is no necessity of the analytical restructuring of the model, the absence of type explosions is guaranteed in a database because not a new table-type, but a new record in one or two tables is added.

The article discusses investigations in a flat rectangular contact area of two elastic solids (brake friction lining and disc) using a theoretical method. The solids are in free as well as in forced movement. The investigations have resulted in correlations describing deformation and stiffness parameters of solid flat joint in different loads: transference of the centre of cross section delta0 the angle of turning phi of one solid in relation to the other (as a result of friction lining deformation), and tension sigmax in any cross section of the contact area. The results of the investigations make it possible to analyze the stiffness of the contact of solids, test the strength of the contact areas, optimize the contact are of solids, and prognosticate even wear out of friction lining.

It is very important to use the exact investment model for energy enterprises. Giant investment is necessary for establishing continued energy systems using renewable energy resources. Demand of the heat energy usually is higher in a winter period compare to the summer time. Program combinations of different heating modus are researched using EnergyPRO.