cadmium usually enter the environment and water resources through wastewater, released by various industries, and may have adverse effects. The current study employs surface of bentonite clay available locally in order to remove cadmium In solutions contaminated with this type of ions, in order to research on a surface with a high ability to adsorption of cadmium (II) ions, study Some factors affect the adsorption process on bentonite clay, such as contact time, pH the solution, Adsorbent particle size, Initial concentration of solutions and temperature of the solution were examined in the a batch process mode. The amount of adsorbed Cd (II) increased with height temperature, the optimum adsorption pH was about 6.5. Under this condition, the percent removal was 95.17%. The adsorption  isotherms were studied and  the results of adsorption processes were more fitted with Friendlich model rather than Langmuir adsorption model. Thermodynamic study showed that,  ΔH was endothermic, ΔG is found to be negative That is, the process is automatic and  ΔS was found to be positive. The current study also involves  practical application using bentonite to get rid of Cd(II) ions  to  from wastewater of Hamdan's station of the Basra- iraq, The results indicate high affinity (97.84%) removal of Cd(II) ions.

Acid-activated corn husk waste (CHW) was used to investigate the adsorption mechanism of Indigo Carmine (IC) dye from an aqueous solution. The effect of different operating parameters such as pH (1-7), initial IC dye concentration (40-400 mg/L), contact time (5-75 min), and heating temperature (25–200 °C) was measured on the removal of IC dye by the CHW. The maximum uptake of IC dye was observed at an initial pH of 2. The maximum capacity of 13.57 mg/g and the maximum dye removal of 89.01 % in wastewater. The adsorbents were characterized using Fourier Transforms Infrared Spectrophotometry (FTIR), Scanning Electron Microscopy (SEM), Brunauer-Emmett-Teller (BET) surface area analysis, X-ray Fluorescence (XRF), and Thermogravimetry Analysis. The characterization process reveals the differences in adsorbent characteristics before and after the adsorption processes. The Langmuir showed the best fitting (R2 = 0.977) and described multilayer adsorption on diverse surfaces. The pseudo-second-order kinetic model best correlated with the experimental data (R2 = 0.981). Thermodynamics revealed that adsorption was favorable spontaneous and exotherm. The study's results indicated that using CHW as a low-cost adsorbent to treat IC dye was efficient and beneficial to the environment.

This paper aims to study the possibility of providing a low-cost alternative for the adsorbents used in the fluoride adsorption from water by using eggshells. Indeed, eggshells were used as an adsorbent for fluoride adsorption from a drinking groundwater sample containing (2.14 mg/l) of fluoride. The eggshells were crushed and sieved into three particle sizes (0.2, 0.5, and 1mm) and then heated at different temperatures ranging from 100 to 250°C. XRD, FT-IR, pHpzc, and TG/DTA analysis were used for the characterization of the adsorbents.  Adsorption batch experiments were carried out to determine the adsorption capacity of eggshell powder such as, particle size, preparation temperature, contact time, and adsorbent dose. A spectrophotometer UV-VIS was used to assess fluoride removal efficiency. The eggshell powder heated at 250°C with 0.2mm of particle size was found to be the most efficient adsorbent, with a maximum fluoride removal efficiency of 51.4%, a maximum adsorption capacity of 0.052mg/g, and a residual fluoride concentration of 1.1mg/l within 150 minutes. The data of the adsorption kinetic on ES250°0.2 were successfully fitted with the pseudo-second-order model with a satisfying coefficient of determination (R2=0.993). The results of the intra-particle diffusion model showed a multi-linearity, revealing that the diffusion of fluoride into the adsorbent was by two stages with diffusion rate constants of Ki = 0.007 (mg /g/min1/2) and Ki = 0.001(mg /g/min1/2) for the first and second stage respectively. An adsorbent dose of 1.5g and 1 hour of contact time were sufficient to decrease fluoride concentration from 2.14 to 1.1mg/l.

Domestic and industrial wastewater contributed to some urban wastewater, which requires specific processing before being disposed into surface waters or reused for irrigation. This paper aimed to employ kaolin as an adsorbent to remove heavy metals from wastewater, as well as aeration and alum to remove nutrients. Experiment were conducted in three parts: first, involved using the aeration method to determine the ideal amount of time to remove or minimize the nutrients. Second, involves treating the solution with potassium alum using various alum doses at the obvious times to eliminate or minimize the nutrients, while third step involves treating the solution with kaolin ore with a size of < 63 µm at various doses, pH, and contact times to remove heavy metals. The findings showed that the aeration method completely removed CO3, OH, PO4, NO3, Ca, and Mn ions after contact time equal 120, 24, 192, 24, 120, and 48 hrs, respectively. Applaying alum treatment method can remove completely CO3, OH, PO4, NO3, and Mn, after contact time 120, 24, 120, 24, and 24 hrs, respectively. When Kaolin ore used as adsorbent, the removal efficiency of  Fe, Cd, Cr, Cu, Sr, Mn, and Zn were; 92, 100, 100, 100, 94, 100, and 88 % ,respectively in 24 hours contact time. The experiment succeeds in treatment of industrial wastewater that was within the range of specified limitations for disposing into surface water or reuse in irrigation field as stated by Egyptian standard code using the three successive treatment techniques.