The applicability of Polyetheretherketone/polyvinylalcohol nanocomposite modified with zinc oxide nanoparticles synthesis for the removal of benzyl butyl phthalate from wastewater. Identical techniques, including BET, FT-IR, XRD, and SEM, have to characterize this unknown material. The investigation shows the applicability of adsorbent PEEK/PVA/ZnONPs, as an available, suitable, and low-cost adsorbent for adequately removing the benzyl butyl phthalate from wastewater. The impacts of variables, including benzyl butyl phthalate concentration, adsorbent, pH, and time (15 mgL-1, 0.3 g, 5.0, and 60 min). Based on the received data, the adsorption of benzyl butyl phthalate on the PEEK/PVA/ZnONPs adsorbent agrees well with the Langmuir adsorption model isotherm (qm = 34.24 mgg-1). The results of the thermodynamic parameter showed a negative enthalpy (-77.0 KJ/mol), a negative Gibbs free energy (-11.7 KJ/mol), and negative entropy (-274.0 J/K.mol). This led to the conclusion that the adsorption process is energetically possible, and exothermic was also spontaneous. This work indicates that the PEEK/PVA/ZnONPs, used as an ecologically adapted, adsorbent holds promise for eliminating benzyl butyl phthalate from wastewater.

cadmium usually enter the environment and water resources through wastewater, released by various industries, and may have adverse effects. The current study employs surface of bentonite clay available locally in order to remove cadmium In solutions contaminated with this type of ions, in order to research on a surface with a high ability to adsorption of cadmium (II) ions, study Some factors affect the adsorption process on bentonite clay, such as contact time, pH the solution, Adsorbent particle size, Initial concentration of solutions and temperature of the solution were examined in the a batch process mode. The amount of adsorbed Cd (II) increased with height temperature, the optimum adsorption pH was about 6.5. Under this condition, the percent removal was 95.17%. The adsorption  isotherms were studied and  the results of adsorption processes were more fitted with Friendlich model rather than Langmuir adsorption model. Thermodynamic study showed that,  ΔH was endothermic, ΔG is found to be negative That is, the process is automatic and  ΔS was found to be positive. The current study also involves  practical application using bentonite to get rid of Cd(II) ions  to  from wastewater of Hamdan's station of the Basra- iraq, The results indicate high affinity (97.84%) removal of Cd(II) ions.

Domestic and industrial wastewater contributed to some urban wastewater, which requires specific processing before being disposed into surface waters or reused for irrigation. This paper aimed to employ kaolin as an adsorbent to remove heavy metals from wastewater, as well as aeration and alum to remove nutrients. Experiment were conducted in three parts: first, involved using the aeration method to determine the ideal amount of time to remove or minimize the nutrients. Second, involves treating the solution with potassium alum using various alum doses at the obvious times to eliminate or minimize the nutrients, while third step involves treating the solution with kaolin ore with a size of < 63 µm at various doses, pH, and contact times to remove heavy metals. The findings showed that the aeration method completely removed CO3, OH, PO4, NO3, Ca, and Mn ions after contact time equal 120, 24, 192, 24, 120, and 48 hrs, respectively. Applaying alum treatment method can remove completely CO3, OH, PO4, NO3, and Mn, after contact time 120, 24, 120, 24, and 24 hrs, respectively. When Kaolin ore used as adsorbent, the removal efficiency of  Fe, Cd, Cr, Cu, Sr, Mn, and Zn were; 92, 100, 100, 100, 94, 100, and 88 % ,respectively in 24 hours contact time. The experiment succeeds in treatment of industrial wastewater that was within the range of specified limitations for disposing into surface water or reuse in irrigation field as stated by Egyptian standard code using the three successive treatment techniques.

In this work, Fe3O4-SiO2 nanoparticles were synthesized, characterized, and applied as adsorbent material to remove methyl blue stain from an aqueous solution. The prepared nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and Brunauer–Emmett–Teller (BET) to determine the physical surface properties and correlate them to the adsorption efficiency. In addition, this study investigated the influence of several parameters on the removal percentage and adsorption capacity. Specifically, this study investigated the impact of changing the following parameters: pH (1 – 8), agitation speed (Uspeed; 100 - 350 rpm), initial methyl blue (MB) concentration (1 - 100 mg/L), adsorbent dose (0.05 to 0.15 g), and contact time (10 - 100 min). The characterization study reveals that the prepared material has an excellent surface area (385 ± 5 m2/g) and pore volume (0.31 cm3/g) which enhances the adsorption capacity. In addition, the prepared material showed excellent efficiency where the removal percentage reached 99.0±1% at the optimal operating conditions and the maximum adsorption capacity was 40 mg/g. This study delivers a full elucidation of the adsorption of MB dye by Fe3O4-SiO2 NPs which considers a promising inexpensive adsorbent. It also delivers important insight information about the adsorption process and the influence of each parameter, which fill the lack in this field.

Batch adsorption process was employed to remove copper(II) and cadmium(II) ions from contaminated water using dried orange peel powder as a cellulosic adsorbent, which supports circular economy and sustainability. Metal ion concentrations were determined using a flame atomic absorption spectroscopy (FAAS). Effects of pH, sorbate-sorbent contact time, metal ion concentration and adsorbent dose on the removal efficiency of the metal ions was investigated. The adsorption equilibrium was reached at 120 and 150 minutes for Cu(II) ions and Cd(II) ions, respectively. At optimized pH and biosorbent load, 10 mg L-1 of Cu(II) and Cd(II)  ions could be removed to the extent 96.9% and 98.1%, respectively, within 2 hrs. However, the percentage removal of metal ions decreased with increasing their initial concentrations. The observed adsorption data was also interpreted in terms of Langmuir and Freundlich adsorption isotherm models. The calculated equilibrium data fitted more adequately with Freundlich model (higher correlation coefficient, R2) than Langmuir model, indicating heterogeneity of adsorption sites due to different functional groups in cellulose. Cd(II) ions showed less binding affinity and less desorption than Cu(II) ions. The maximum adsorption capacity (qmax) of dried orange peel were 2.78 mg/g and 2.57 mg/g for copper(II) and cadmium(II) ions, respectively.

This work explores the synthesis and characterization of two novel nanocomposites that can be used in various applications, such as aqueous solution adsorption of pollutants. The first nanocomposite consists of tin (Sn)-doped titanium dioxide (TiO2) on activated carbon, while the other one consists of polypyrole (PPy), chitosan (CS), and Sn-doped TiO2. A contrast was made of their effective adsorbent materials for the removal of Cibacron Brilliant Yellow dye from aqueous solutions. Different analytical techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), energy dispersive X-ray analysis (EDX), and Fourier transform - infrared (FT-IR) were used to analysis the nanocomposite samples. SEM images show that the average particle diameter of PPy-CS/Sn-doped TiO2 NC is 75 ± 3 nm, while Sn-doped TiO2/AC particles have an average diameter of 40 ± 2 nm. The greater PPy-CS/Sn-doped TiO2 nanocoposite particle diameter indicates that the polymers cover the Sn-doped TiO2 nanoparticles, which leads to higher in the diameter of the particles. The adsorption efficiency of Sn-doped TiO2/AC was higher than that of PPy-CS/Sn-doped TiO2 sample due to its smaller particle size which resulted in a higher surface area which provides more adsorption sites. However, both samples showed remarkable adsorption capacity, where the adsorption capacity of Sn-doped TiO2/AC and PPy-CS/Sn-doped TiO2 were 104 and 103 mg/g, respectively.

The present research investigates the ability of graphene oxide nanosheets for treatment of dairy wastewater, using In Situ Sludge Magnetic Impregnation” (ISSMI) to separate sludge after adsorption process. To increase the interaction between magnetic nanoparticles and graphene oxide, the former has been functionalized, using 3-Aminopropyl triethoxysilane, with the synthesized graphene oxide and magnetic nanoparticles being characterized by FT-IR, SEM, and NCHS analysis. The experiments have been conducted on the effluent of Pegah factory. The batch adsorption experiments have been carried out to investigate the effect of adsorbent dose, contact time, and pH on the removal of total nitrogen, total phosphorus, COD, and turbidity. At adsorbent dose of 320 mg L-1, the removal efficiencies of 90, 80, 84, and 94% have been observed for TN, TP, COD, and turbidity, respectively. The adsorbent data has been modeled by Langmuir and Freundlich isotherms, giving results that are compatible with Freundlich isotherm. TN, TP, and COD are mostly particulate materials in dairy wastewaters; therefore, when nanosheets aggregate, particulate materials are trapped between GO nanosheets; as a result, pollutants are distributed heterogeneously on the adsorbent's surface. Consequently, adsorption does not occur as monolayer on the surface of GO; for this reason, adsorption follows Freundlich model. Maximum absorption capacity of the adsorbent turns out to be 730 mg g-1 for total nitrogen, 600 mg g-1 for total phosphorus, 26000 mg g-1 for COD, and 5500 mg g-1 for turbidity. Adsorption kinetic has been studied with the first and second order equation, giving results that are compatible with second order equation.

Trace metal elements are toxic to the environment and human health and can be removed from water through adsorption. Development of low-cost adsorbents would always been a matter of achievement of every adsorption study as usually many adsorbents were found to be expensive in nature. In this regard, biochar adsorbents gained significant attention due to high adsorption capacity, low-cost and environmental sustainability. Pyrolysis is used to produce biochar adsorbents at varying temperature ranged from 300°C-700°C. The adsorption capacities of palm fiber biochar adsorbents are remarkable which was found around ~198 mg/g for cadmium removal. However, bamboo-based biochar had 868 mg/g of adsorption capacity for arsenate removal. This review aims to provide the current discusses the sources and impacts of trace metal elements in water along with properties of biochar including its composition, surface area, pore structure, and surface functional groups. Further, various types of biomasses have also been mentioned for producing biochar such as agricultural wastes, food wastes, forestry residues, etc. The paper also discusses the different types of mechanisms involved in the adsorption of heavy metal biochar adsorbents like electrostatic attraction, ion exchange, surface complexation etc.

Cedrus deodara is a coniferous tree native to Himalayan region. Its wood is a valuable resource for the timber industry; however, its bark is typically discarded as a waste material. The present study examines the performance of Cedrus deodara bark powder (CD) as an inexpensive adsorbent for elimination of Pb (II) ions. In addition to this multiple linear regression (MLR) and artificial neural network (ANN) models were developed for modelling the adsorption process and prediction of Pb (II) removal efficiency. The structural and chemical properties of CD were explored using Field Emission Scanning Electron Microscope (FE-SEM), Energy Dispersive Spectrometer (EDS), X-Ray Diffractometer (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). Batch experiments were conducted to investigate the influence of factors including pH, contact time, initial Pb (II) concentration and temperature on Pb (II) adsorption. The adsorption followed pseudo-second-order kinetic and Langmuir isotherm models with maximum monolayer uptake capacity 77.52 mg/g. Based on the thermodynamic criteria, the process was endothermic and spontaneous with enthalpy change (ΔH = 8.08 kJ/mol), free energy change (ΔG = -2.44 kJ/mol) and entropy change (ΔS = 0.03 kJ/K/mol). Statistical comparison of MLR model (R2 = 0.817, RMSE = 8.954, MAPE = 17.379 %) and ANN model (R2 = 0.993, RMSE = 1.777, MAPE = 2.054 %) confirmed that ANN model was far more accurate in predicting removal efficiency.

Acid-activated corn husk waste (CHW) was used to investigate the adsorption mechanism of Indigo Carmine (IC) dye from an aqueous solution. The effect of different operating parameters such as pH (1-7), initial IC dye concentration (40-400 mg/L), contact time (5-75 min), and heating temperature (25–200 °C) was measured on the removal of IC dye by the CHW. The maximum uptake of IC dye was observed at an initial pH of 2. The maximum capacity of 13.57 mg/g and the maximum dye removal of 89.01 % in wastewater. The adsorbents were characterized using Fourier Transforms Infrared Spectrophotometry (FTIR), Scanning Electron Microscopy (SEM), Brunauer-Emmett-Teller (BET) surface area analysis, X-ray Fluorescence (XRF), and Thermogravimetry Analysis. The characterization process reveals the differences in adsorbent characteristics before and after the adsorption processes. The Langmuir showed the best fitting (R2 = 0.977) and described multilayer adsorption on diverse surfaces. The pseudo-second-order kinetic model best correlated with the experimental data (R2 = 0.981). Thermodynamics revealed that adsorption was favorable spontaneous and exotherm. The study's results indicated that using CHW as a low-cost adsorbent to treat IC dye was efficient and beneficial to the environment.