Refine search
Results 1-10 of 136
Optimized parameters of the electrocoagulation process using a novel reactor with rotating anode for saline water treatment
2020
Al-Raad, Abbas A. | Hanafiah, Marlia M. | Naje, Ahmed Samir | Ajeel, Mohammed A.
In this study, a novel rotating anode-based reactor (RAR) was designed to investigate its effectiveness in removing dissolved salts (i.e., Br⁻, Cl⁻, TDS, and SO₄²⁻) from saline water samples. Two configurations of an impeller’s rotating anode with various operation factors, such as operating time (min), rotating speed (rpm), current density (mA/cm²), temperature (°C), pH, and inter-electrode space (cm), were used in the desalination process. The total cost consumed was calculated on the basis of the energy consumption and aluminum (Al) used in the desalination. In this respect, operating costs were calculated using optimal operating conditions. Salinity was removed electrochemically from saline water through electrocoagulation (EC). Results showed that the optimal adjustments for treating saline water were carried out at the following conditions: 150 and 75 rpm rotating speeds for the impeller’s rod anode and plate anode designs, respectively; 2 mA/cm² current density (I), 1 cm² inter-electrode space, 25 °C temperature, 10 min operation time, and pH 8. The results indicated that EC technology with impeller plates of rotating anode can be considered a very cost-effective technique for treating saline water.
Show more [+] Less [-]Electrocatalytical oxidation of arsenite by reduced graphene oxide via in-situ electrocatalytic generation of H2O2
2019
Li, Xuheng | Liu, Feng | Zhang, Weifang | Lü, Hongbo | Zhang, Jing
Preoxidation of As(III) to As(V) is required for the efficient removal of total arsenic in the treatment of wastewater. In this work, the electro-Fenton oxidation of As(III) with a high efficiency was successfully achieved by using the system of the stainless steel net (SSN) coating with reduced graphene oxide (RGO@SSN) as the cathode and stainless steel net (SSN) as the sacrificial anode. The RGO@SSN was synthesized by electrophoretic deposition-annealing method. The carbon disorder and defects of RGO resulted from the remained oxygen-containing functional groups facilitated the electrocatalytically active sites for two-electron oxygen reduction reaction (ORR). A high concentration (up to 1000 μmol/L) of H₂O₂ was in-situ produced through two-electron oxygen reduction reaction of electro-catalysis, and then served as the electro-Fenton reagent for the oxidation of As(III). HO generated by H₂O₂ participating the electro-Fenton reaction or decomposed at the surface of RGO@SSN cathode at acid condition endowed the strong oxidizing ability for As(III). The electro-Fenton equipped with RGO@SSN cathode has a promising application in the oxidation and removal of organic or inorganic pollutants in wastewater.
Show more [+] Less [-]Integrated approach of photo-assisted electrochemical oxidation and sequential biodegradation of textile effluent
2022
Prakash, Arumugam Arul | Sathishkumar, Kuppusamy | AlSalhi, Mohamad S. | Devanesan, Sandhanasamy | Mani, Panagal | Kamala-Kannan, Seralathan | Vijayanand, Selvaraj | Rajasekar, Aruliah
Synthetic azo dyes are extensively used in the textile industries, which are being released as textile effluent into the environment presence of azo dyes in the environment is great environmental concern therefore treatment of textile effluent is crucial for proper release of the effluent into the environment. Electrochemical oxidation (EO) is extensively used in the degradation of pollutants because of its high efficiency. In this study, photo-assisted electrooxidation (PEO) followed by biodegradation of the textile effluent was evaluated. The pretreatment of textile effluent was conducted by EO and PEO in a tubular flow cell with TiO₂–Ti/IrO₂–RuO₂ anode and titanium cathode under different current densities (10, 15, and 20 mA cm⁻²). The chemical oxygen demand level reduced from 3150 mg L⁻¹ to 1300 and 600 mg L⁻¹under EO and PEO, respectively. Furthermore, biodegradation of EO and PEO pretreated textile effluent shows reduction in chemical oxygen demand (COD) from 1300 mg L⁻¹ to 900 mg L⁻¹and 600 mg L⁻¹to 110 mg L⁻¹, respectively. The most abundant genera were identified as Acetobacter, Achromobacter, Acidaminococcus, Actinomyces, and Acetomicrobium from the textile effluent. This study suggests that an integrated approach of PEO and subsequent biodegradation might be an effective and eco-friendly method for the degradation of textile effluent.
Show more [+] Less [-]Coupled with EDDS and approaching anode technique enhanced electrokinetic remediation removal heavy metal from sludge
2021
Tang, Jian | Qiu, Zhongping | Tang, Hengjun | Wang, Haiyue | Sima, Weiping | Liang, Chao | LIao, Yi | Li, Zhihua | Wan, Shan | Dong, Jianwei
In this work, the novel technology was used to remove heavy metal from sludge. The coupled with biodegradable ethylenediamine disuccinic acid (EDDS) and approaching anode electrokinetic (AA-EK) technique was used to enhance heavy metal removing from sludge. Electric current, sludge and electrolyte characteristics, heavy metal removal efficiency and residual content distribution, and heavy metal fractions percentage of variation were evaluated during the electrokinetic remediation process. Results demonstrated that the coupled with EDDS and AA-EK technique obtain a predominant heavy metal removal efficiency, and promote electric current increasing during the enhanced electrokinetic remediation process. The catholyte electrical conductivity was higher than the anolyte, and electrical conductivity of near the cathode sludge achieved a higher value than anode sludge during the coupled with EDDS and AA-EK remediation process. AA-EK technique can produce a great number of H⁺, which caused the sludge acidification and pH decrease. Cu, Zn, Cr, Pb, Ni and Mn obtain the highest extraction efficiency after the coupled with EDDS and AA-EK remediation, which were 52.2 ± 2.57%, 56.8 ± 3.62%, 60.4 ± 3.62%, 47.2 ± 2.35%, 53.0 ± 3.48%, 54.2 ± 3.43%, respectively. Also, heavy metal fractions analysis demonstrated that the oxidizable fraction percentage decreased slowly after the coupled with EDDS and AA-EK remediation.
Show more [+] Less [-]Response of sediment microbial communities to crude oil contamination in marine sediment microbial fuel cells under ferric iron stimulation
2020
Hamdan, Hamdan Z. | Salam, Darine A.
In this study, response of the microbial communities associated with the bioremediation of crude oil contaminated marine sediments was addressed using sediment microbial fuel cells (SMFCs). Crude oil was spiked into marine sediments at 1 g/kg of dry sediment to simulate a heavily contaminated marine environment. Conventional SMFCs were used with carbon fiber brushes as the electrode components and were enhanced with ferric iron to stimulate electrochemically active bacteria. Controls were operated under open circuit with and without ferric iron stimulation, with the latter condition simulating natural attenuation. Crude oil removal in the Fe enhanced SMFCs reached 22.0 ± 5.5% and was comparable to the measured removal in the control treatments (19.2 ± 7.4% in natural attenuation SMFCs and 15.2 ± 2.7% in Fe stimulated open circuit SMFCs), indicating no major enhancement to biodegradation under the applied experimental conditions. The low removal efficiency could be due to limitations in the mass transfer of the electron donor to the microbes and the anodes. The microbial community structure showed similarity between the iron stimulated SMFCs operated under the open and closed circuit. Natural attenuation SMFCs showed a unique profile. All SMFCs showed high relative abundances of hydrocarbon degrading bacteria rather than anode reducers, such as Marinobacter and Arthrobacter in the case of the natural attenuation SMFCs, and Gordonia in the case of iron stimulated SMFCs. This indicated that the microbial structure during the bioremediation process was mainly determined by the presence of petroleum contamination and to a lesser extent the presence of the ferric iron, with no major involvement of the anode as a terminal electron acceptor. Under the adopted experimental conditions, the absence of electrochemically active microbes throughout the biodegradation process indicates that the use of SMFCs in crude oil bioremediation is not a successful approach. Further studies are required to optimize SMFCs systems for this aim.
Show more [+] Less [-]Electrochemical oxidation of ceftazidime with graphite/CNT-Ce/PbO2–Ce anode: Parameter optimization, toxicity analysis and degradation pathway
2020
Duan, Pingzhou | Gao, Shiheng | Lei, Jiawei | Li, Xiang | Hu, Xiang
In this work, the electrochemical degradation of antibiotic ceftazidime has been studied using a novel rare earth metal Ce and carbon nanotubes codoped PbO₂ electrode. A competitively high oxygen evolution potential (2.4 V) and enhanced catalytic surface area were obtained, evidence by LSV and CV electrochemical characterization. The G/CNT-Ce/PbO₂–Ce electrode possessed a more compact structure and a smaller grain size than the other PbO₂ and Ce–PbO₂ electrodes, exhibiting a prolonged service lifetime, evidence by accelerated lifespan test and recycling degradation experiment. As electrolysis time reached 120 min, the removal efficiency of ceftazidime and TOC arrived at 100.0% and 54.2% respectively in 0.05 M Na₂SO₄ solution containing 50 mg⋅L⁻¹ ceftazidime. The effect of applied current density, pH value, initial ceftazidime concentration and chloride contents on the degradation performance were systematically evaluated. The results demonstrated that electrochemical oxidation of ceftazidime over the G/CNT-Ce/PbO₂–Ce electrode was highly effective, and the mineralization rate was greatly improved, compared with pristine PbO₂ electrode. Considering the toxicity was increased after 30 min electrolysis, the intermediates were quantitatively investigated through HPLC-MS, GC-MS and IC technology. According to the identified products, a reaction mechanism has been proposed and pyridine and aminothiazole were detected with concentration from approximately 1 to 3 mg⋅L⁻¹, which were regarded as toxic byproducts during electrooxidation. Further electrocatalyzing by ring cleavage reaction and complete mineralization to CO₂, NO₃⁻ and NH₄⁺ was proposed, which demonstrated the G/CNT-Ce/PbO₂–Ce electrode exhibited high efficiency for ceftazidime removal in mild conditions.
Show more [+] Less [-]Remediation of heavy metal contaminated soils by organic acid extraction and electrochemical adsorption
2020
Yang, Xiong | Liu, Lihu | Tan, Wenfeng | Liu, Chengshuai | Dang, Zhi | Qiu, Guohong
Remediation of heavy metal contaminated soils remains a global challenge. Here, low-molecular-weight organic acids were used to extract Cu and Zn from polluted soils, and the extracted heavy metals were subsequently adsorbed by activated carbon electrodes. The electrochemical adsorption mechanism as well as the influence of pH, organic acid type and voltage were investigated, and the soil remediation effect was further evaluated by the cultivation of rape. After extraction by citrate at initial pH 8.3 and electrochemical adsorption at 0.9 V for 7 d, the concentrations of total and bioavailable Cu in soils decreased from 1090 to 281 to 391 and 52 mg kg⁻¹, and those of Zn decreased from 262 to 39 to 208 and 30 mg kg⁻¹, respectively. Cu and Zn ions were mainly electrochemically adsorbed on the carbon cathode and anode, respectively, resulting in decreases of their concentrations to below 1 mg L⁻¹ in the leachate. The presence of organic acids improved the remediation performance in the order of citrate > oxalate > acetate. The decrease in the initial pH of citrate solution enhanced the removal rate of Zn, while seemed to have no effect on that of Cu. The removal capacity for heavy metals decreased with decreasing cell voltage from 0.9 to 0.3 V. In the rape cultivation experiment, the Cu and Zn contents in shoot and root were decreased by more than 50%, validating the soil remediation effect. The present work proposes a facile method for heavy metal removal from contaminated soils.
Show more [+] Less [-]Removal effect of enrofloxacin from mariculture sediments by bioelectrochemical system and analysis of microbial community structure
2022
Ding, Nan | Jin, Chunji | Zhao, Nannan | Zhao, Yangguo | Guo, Liang | Gao, Mengchun | She, Zonglian | Ji, Junyuan
Based on the application of sediment microbial fuel cell (SMFC) in the bioremediation of sediment, this study used the sediment microbial fuel cell technology as the leading reactor. Modification of anode carbon felts (CF) by synthesis of PANI/MnO₂ composited to improve the electrical performance of the sediment microbial fuel cell. This study investigated the degradation effects, degradation pathways of the specific contaminant enrofloxacin and microbial community structure in sediment microbial fuel cell systems. The results showed that the sediment microbial fuel cell system with modified anode carbon felt (PANI-MnO₂/CF) prepared by in-situ chemical polymerization had the best power production performance. The maximum output voltage was 602 mV and the maximum power density was 165.09 mW m⁻². The low concentrations of enrofloxacin (12.81 ng g⁻¹) were effectively degraded by the sediment microbial fuel cell system with a removal rate of 59.52%.
Show more [+] Less [-]PCDD/Fs emissions from secondary copper production synergistically controlled by fabric filters and desulfurization
2021
Li, Haifeng | Liu, Wenbin | Lu, Anxiang | Li, Cheng | Die, Qingqi | Lei, Rongrong | Wu, Xiaolin
The effects of fabric filters and desulfurization systems during secondary copper smelting on polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) concentrations, emission coefficients, and profiles were studied in an oxygen-rich smelting furnace and an anode furnace. In the anode furnace, the toxic equivalent (TEQ) concentration ranges were 0.106–1.04 ng World Health Organization (WHO)-TEQ/m³ at the fabric filters inlet and 0.027–0.17 ng WHO-TEQ/m³ at the outlet. For the oxygen-rich smelting furnace, the TEQ concentration ranges were 1.21–1.93 and 0.010–0.019 ng WHO-TEQ/m³ at the desulfurization system inlet and outlet, respectively. The TEQs in the outlet stack gases of the desulfurization system from the anode furnace were 0.0041–0.016 ng WHO-TEQ/m³. It is likely that PCDD/Fs that were taken away from the stack gases were adsorbed by the fly ash and gypsum. Solid residues were the dominant release routes for PCDD/Fs. PCDD/Fs congener and homologue profiles of stack gases from different smelting stages were similar. The contributions of more chlorinated homologues from the anode furnace decreased observably after the stack gases passed through the fabric filters. However, the desulfurization process did not greatly change the PCDD/Fs homologue profiles. Overall, both the fabric filters and desulfurization systems showed excellent removal efficiencies for PCDD/Fs in the stack gases, which reduced the TEQ emissions to well below the 0.5 ng WHO-TEQ/m³ to achieve standard discharge.
Show more [+] Less [-]Treatment of microplastics in water by anodic oxidation: A case study for polystyrene
2021
Kiendrebeogo, Marthe | Karimi Estahbanati, M.R. | Khosravanipour Mostafazadeh, Ali | Drogui, Patrick | Tyagi, R.D.
Water pollution by microplastics (MPs) is a contemporary issue which has recently gained lots of attentions. Despite this, very limited studies were conducted on the degradation of MPs. In this paper, we reported the treatment of synthetic mono-dispersed suspension of MPs by using electrooxidation (EO) process. MPs synthetic solution was prepared with distilled water and a commercial polystyrene solution containing a surfactant. In addition to anode material, different operating parameters were investigated such as current intensity, anode surface, electrolyte type, electrolyte concentration, and reaction time. The obtained results revealed that the EO process can degrade 58 ± 21% of MPs in 1 h. Analysis of the operating parameters showed that the current intensity, anode material, electrolyte type, and electrolyte concentration substantially affected the MPs removal efficiency, whereas anode surface area had a negligible effect. In addition, dynamic light scattering analysis was performed to evaluate the size distribution of MPs during the degradation. The combination of dynamic light scattering, scanning electron microscopy, total organic carbon, and Fourier-transform infrared spectroscopy results suggested that the MPs did not break into smaller particles and they degrade directly into gaseous products. This work demonstrated that EO is a promising process for degradation of MPs in water without production of any wastes or by-products.
Show more [+] Less [-]