In this work, we report on the synthesis and characterization of nanoporous bimetallic metal-organic frameworks (FeCo-BDC). Effects of synthesis time and temperature on the structures, morphology, and catalytic performance of FeCo-BDC were investigated. Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET) were used to reveal the morphological and textural characteristics. The crystal structure and chemical composition of FeCo-BDC were determined by means of X-ray powder diffraction (XRD), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Photoelectron Spectroscopy (XPS), and Inductively Coupled Plasma Mass Spectrometry (ICP-MS) measurements. Interestingly, FeCo-BDC grew into the same crystal structure with different morphology in the temperature of 110–150 °C with 12–48 h. The heterogeneous catalytic activity of FeCo-BDC was tested to activate peroxydisulfate (PDS) and peroxymonosulfate (PMS) for removal of methylene blue (MB). The results found that FeCo-BDC synthesized at 150 °C with 24 h exhibited the best catalytic performance for PMS and obtained 100% of MB removal within 15 min. The abundant unsaturated metal active sites of Fe(II) and Co(II) in the skeleton of FeCo-BDC made a great contribution to the generation of sulfate (▪) and hydroxyl radicals (OH), which resulted in the excellent performance for MB degradation.

Per- and polyfluoroalkyl substances (PFASs) are a large group of chemicals and can be detected in environmental and human samples all over the world. Toxicity of existing and emerging PFASs will be a long-term source of concern. This study aimed to investigate structure-dependent inhibitory effects of 14 PFASs towards the activity of 11 UDP-glucuronosyltransferase (UGT) isoforms. In vitro UGTs-catalyzed glucuronidation of 4-methylumbelliferone (4-MU) was employed to determine the inhibition of PFASs towards different UGT isoforms. All the PFASs showed <75% of inhibition or stimulation effects on UGT1A3, UGT1A7, UGT1A9, UGT2B4, UGT2B7 and UGT2B17. However, PFASs showed broad inhibition on the activity of UGT1A1 and UGT1A8. The activity of UGT1A1 was inhibited by 98.8%, 98%, 79.9%, 77.1%, and 76.9% at 100 μmoL/L of perfluorodecanoic acid (PFDA), perfluorooctanesulfonic acid potassium salt (PFOS), perfluorotetradecanoic acid (PFTA), perfluorooctanoic acid (PFOA) and perfluorododecanoic acid (PFDoA), respectively. UGT1A8 was inhibited by 97.6%, 94.8%, 86.3%, 83.4% and 77.1% by PFDA, PFTA, perfluorooctadecanoic acid (PFOcDA), PFDoA and PFOS, respectively. Additionally, PFDA significantly inhibited UGT1A6 and UGT1A10 by 96.8% and 91.6%, respectively. PFDoA inhibited the activity of UGT2B15 by 88.2%. PFDA and PFOS exhibited competitive inhibition towards UGT1A1, and PFDA and PFTA showed competitive inhibition towards UGT1A8. The inhibition kinetic parameter (Kᵢ) were 3.15, 1.73, 13.15 and 20.21 μmoL/L for PFDA-1A1, PFOS-1A1, PFDA-1A8 and PFTA-1A8, respectively. The values were calculated to be 0.3 μmoL/L and 1.3 μmoL/L for the in vivo inhibition of PFDA towards UGT1A1-and UGT1A8-catalyzed metabolism of substances, and 0.2 μmoL/L and 2.0 μmoL/L for the inhibition of PFOS towards UGT1A1 and the inhibition of PFTA towards UGT1A8, respectively. Molecular docking indicated that hydrogen bonds and hydrophobic interactions contributed to the interaction between PFASs and UGT isoforms. In conclusion, exposure to PFASs might inhibit the activity of UGTs to disturb metabolism of endogenous compounds and xenobiotics. The structure-related effects of PFASs on UGTs would be very important for risk assessment of PFASs.

Preoxidation of As(III) to As(V) is required for the efficient removal of total arsenic in the treatment of wastewater. In this work, the electro-Fenton oxidation of As(III) with a high efficiency was successfully achieved by using the system of the stainless steel net (SSN) coating with reduced graphene oxide (RGO@SSN) as the cathode and stainless steel net (SSN) as the sacrificial anode. The RGO@SSN was synthesized by electrophoretic deposition-annealing method. The carbon disorder and defects of RGO resulted from the remained oxygen-containing functional groups facilitated the electrocatalytically active sites for two-electron oxygen reduction reaction (ORR). A high concentration (up to 1000 μmol/L) of H₂O₂ was in-situ produced through two-electron oxygen reduction reaction of electro-catalysis, and then served as the electro-Fenton reagent for the oxidation of As(III). HO generated by H₂O₂ participating the electro-Fenton reaction or decomposed at the surface of RGO@SSN cathode at acid condition endowed the strong oxidizing ability for As(III). The electro-Fenton equipped with RGO@SSN cathode has a promising application in the oxidation and removal of organic or inorganic pollutants in wastewater.

CuFeO₂/CeO₂ as a novel catalyst was synthesized and its catalytic performance was evaluated for electro-Fenton degradation of acid orange 7 (AO7). It was demonstrated from the characterization results that the rhombohedral structure of CuFeO₂ and face-centered cubic fluorite structure of CeO₂ remained stable after nanocomposite construction. The impact of such operating parameters as pH, current intensity and, catalyst amount was investigated and the optimum conditions (100 mgL⁻¹ AO7, pH 3, 150 mgL⁻¹ CuFeO₂/CeO₂, I: 150 mA) determination led to 99.3% AO7 removal and 79.1% COD removal in 60 min. The introduction of CeO₂ as non-inert support had a significant impact on H₂O₂ electro-generation as an important step in AO7 removal. CuFeO₂/CeO₂ presented negligible metal leaching (iron 4.13%, copper 2.4%, and cerium 0.33%) which could be due to the strong interaction between active species and support. The nanocomposite performed efficiently in salty systems and two samples of real wastewaters due to Brønsted acidity character of ceria, which makes it a potential choice in industrial applications. The good performance of nanocomposite could be the result of the synergistic effect between Fe, Cu, and Ce. Regarding scavenging measurements results, the electro-Fenton process followed the Haber-Weiss mechanism. The by-products detection was performed using GC-MS analysis to propose an acceptable pathway for EF degradation of AO7. The BMG kinetics model (1/b = 0.969 (min) and 1/m = 0.269 (min⁻¹)) was matched with the experimental data and described the kinetics of reaction very well. The catalytic activity of CuFeO₂/CeO₂ almost remained after six cycles. Based on the obtained results, CuFeO₂/CeO₂ using the benefit of the synergistic effect of Ce³⁺ with Fe²⁺ and Cu⁺can be introduced as a promising novel catalyst for the electro-Fenton reaction in wastewater treatment.

The removals of arsenic and selenium pollutants are always urgent desires for the water security. In this study, both sorption and catalysis strategies were combined for the effective removals of As(V) and Se(VI) over magnetic graphene oxide sheets (GOs)-oxidized carbon nanotubes (OCNTs) hydrogels. The sorption behavior facilitated the operation of catalysis reactions, meanwhile, the catalytic reduction promoted the release of occupied sorption sites and then restarted a new sorption-catalysis cycle. The synergic effect of sorption and catalysis realized 258.2 mg g⁻¹ for As(V) enrichment capacity on MPG2T1, and ultra-fast sorption and catalysis equilibriums were identified within 9 min. In the case of Se(VI), a moderate enrichment performance was observed to be 46.2 mg g⁻¹. Similarly, the ultra-fast sorption and reduction of Se(VI) were realized within 2 min. In the competition experiments, only SO₄²⁻, SO₃²⁻, and HPO₄²⁻ showed interference for As(V) and Se(VI) removals. These results testified the superiority of the synergy effect of sorption and catalysis, and the feasibility of 3D magnetic GOs-OCNTs hydrogel in practical implementations.

Spiramycin is a widely used macrolide antibiotic and exists at high concentration in production wastewater. A thermal-acid hydrolytic pretreatment using silicotungstic acid (STA) under microwave (MW) irradiation was suggested to mitigate spiramycin from production wastewater. Positive correlations were observed between STA dosage, MW power, interaction time and the hydrolytic removal efficiencies, and an integrative equation was generalized quantitively. Rapid and complete removal 100 mg/L of spiramycin was achieved after 8 min of reaction with 1.0 g/L of STA under 200 W of MW irradiation, comparing to 30.1% by MW irradiation or 15.9% by STA alone. The synergetic effects of STA and MW irradiation were originated from the dissociated-proton catalysis by STA and the dipolar rotation heating effect of MW. STA performed much better than the mineral acid H2SO4 under MW, due to the much stronger Brönsted acidity and higher Hammett acidity. After 8 min, 98.0% of antibacterial potency was also reduced. The m/z 558.8614 fragment (P1) and m/z 448.1323 fragment (P2) were identified as the primary products, which were formed by breaking glucosidic bonds and losing mycarose and forosamine for P1 and further mycaminose moiety for P2. Finally, production wastewater with 433 mg/L of spiramycin was effectively treated using this thermal-acid hydrolytic method. Spiramycin and its antibacterial potency both dropped to 0 after 6 min. The potency drop was supposed from the losing of mycarose and/or forosamine. To decrease both the concentration of spiramycin and its antibacterial potency, combinedly using STA and MW was suggested in this work to break down the structural bonds of the functional groups rather than to destroy the whole antibiotic molecules. It is promising for pretreating spiramycin-contained production wastewater to mitigate both the antibiotic and its antibacterial potency.

Once released into the environment, engineered nanomaterials can significantly influence the transformation and fate of organic contaminants. To date, the abilities of composite nanomaterials to catalyze environmentally relevant abiotic transformation reactions of organic contaminants are largely unknown. Herein, we investigated the effects of two nanocomposites – consisting of anatase titanium dioxide (TiO2) with different predominantly exposed crystal facets (i.e., {101} or {001} facets) anchored to hydroxylated multi-walled carbon nanotubes (OH-MWCNT) – on the hydrolysis of 1,1,2,2-tetrachloroethane (TeCA), a common groundwater contaminant, at ambient pH (6, 7 and 8). Both OH-MWCNT/TiO2 nanocomposites were more effective in catalyzing the dehydrochlorination of TeCA than the respective component materials (i.e., bare OH-MWCNT and bare TiO2). Moreover, the synergistic effect of the two components was evident, in that the incorporation of OH-MWCNT increased the TeCA adsorption capacity of the nanocomposites, significantly enhancing the catalytic effect of the deprotonated hydroxyl and carboxyl groups on nanocomposite surfaces, which served as the main catalytic sites for TeCA hydrolysis. The findings may have important implications for the understanding of the environmental implications of composite nanomaterials and may shed light on the design of high-performance nanocomposites for enhanced contaminant removal.

Aiming at realizing heavy metal recycling and resource utilization, a carbon-based iron catalyst (Fe@C) was synthesized through a resin carbonization method, and adopted for peroxymonosulfate (PMS) activation to remove bisphenol S (BPS), an emerging aquatic contaminant. This study demonstrated that Fe@C exhibited excellent catalytic potential for BPS degradation with a relatively low activation energy (Ea = 29.90 kJ/mol). Kinetic factors affecting the activation performance were thoroughly investigated. The obtained results indicated that Fe@C composite exhibited the superior uniformity with carbon as the framework and granular iron oxide as the coverage. pH increase could cause the inhibitive effect on BPS degradation, while the increasing catalyst loading (0.05–0.5 g/L) was conducive for the catalytic performance of Fe@C, with an optimal PMS concentration at 1.0 mM. A negative influence on BPS degradation was obtained in the presence of SO42−, HCO3− and lower concentration of Cl− (0–20 mM), compared to the promotion at higher concentration of Cl− (>50 mM). Based on the electron spin resonance (ESR) monitoring and radical scavenging results, it is demonstrated that singlet oxygen, a non-radical species, emerged together with ·SO4− and ·OH for BPS degradation. A three-channel catalytic mechanism was verified through typical characterizations. Furthermore, the degradation pathway of BPS was proposed based on the identified intermediates. This novel carbon-based activator for PMS showed notable potential for the waste resin recycling and water decontamination.A novel Fe-based activator carbonized from a saturated resin exhibits excellent performance for Bisphenol S degradation with activated peroxymonosulfate.

The aim of this work was to develop a new modified graphite felt (GF) as carbonaceous cathode for electro-Fenton (EF) application loaded with nitrogen-doped porous carbon (NPC) carbonized by zeolitic imidazolate framework-8 (ZIF-8) nanocrystals as carbon precursor. At initial pH 7, the highest generation rate of H₂O₂ was 0.74 mg h⁻¹ cm⁻² by applying 12.5 mA cm⁻² by modified cathode, but in the same condition, the GF only had 0.067 mg h⁻¹ cm⁻². The production efficiency increased 10 times. Additionally, phenol (50 mg L⁻¹) could be largely removed by NPC modified cathode, the mineralization ratio and TOC reached 100% and 82.61% at 120 min of optimization condition, respectively. The NPC cathode kept its stability after 5 cycles. The materials were characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and linear sweep voltammetry (LSV). The results demonstrated that a homogenous NPC covered the carbon-based material GF. The existing graphitic-N and sp² carbon of NPC promoted the electron transfer between carbon surface and oxygen molecules, as well as accelerated the oxygen reduction reaction (ORR) and the modified graphite felt had much higher electrocatalytic activity. In this work, several manufacturing parameters like the current, pH and load of NPC were optimized. The optimized design could improve the efficiency of new cathode with in situ electro-chemical production of H₂O₂ and significantly offer a potential material for degradation of organic pollutants.

Immobilization of enzymes on carriers have been pursued to make the enzyme stable, reusable and obtaining even better enzyme activity. Due to the highly stable two-dimensional layer structure, large surface area and pore volume, graphene materials were seemed as ideal carrier for enzyme immobilization. In this paper, pristine few layer graphene (FLG) was applied to interact with laccase to synthesize laccase-graphene composite and the results of AFM, FT-IR and adsorption isotherm suggested that laccase was loaded on the FLG with a very high loading dosage (221.1 mg g⁻¹). Based on the measured interaction force and binding type between laccase and graphene, we proposed that the great enzyme loading on FLG is likely due to the non-covalent π-π stacking in addition to the large surface area of FLG. The composite has better stability to the variance of pH and storage temperature than free laccase. The synthesized composite can effectively transform beta-blocker labetalol with an enhanced efficiency, though the possible reaction pathways kept not changing. We further performed molecular simulation study on the crystal structure variation of laccase binding on FLG and proposed that catalytic activity enhancement may be attributed to the more exposure extent of the catalytic center of laccase. In addition, the laccase-graphene composite can be reused more than ten times in catalyzing the labetalol removal.