There is currently great interest in replacing fossil-oil with renewable fuels in energy production. Fast pyrolysis bio-oil (FPBO) made of lignocellulosic biomass is one such alternative to replace fossil oil, such as heavy fuel oil (HFO), in energy boilers. However, it is not known how this fuel change will alter the quantity and quality of emissions affecting human health. In this work, particulate emissions from a real-scale commercially operated FPBO boiler plant are characterized, including extensive physico-chemical and toxicological analyses. These are then compared to emission characteristics of heavy fuel-oil and wood fired boilers. Finally, the effects of the fuel choice on the emissions, their potential health effects and the requirements for flue gas cleaning in small-to medium-sized boiler units are discussed.The total suspended particulate matter and fine particulate matter (PM₁) concentrations in FPBO boiler flue gases before filtration were higher than in HFO boilers and lower or on a level similar to wood-fired grate boilers. FPBO particles consisted mainly of ash species and contained less polycyclic aromatic hydrocarbons (PAH) and heavy metals than had previously been measured from HFO combustion. This feature was clearly reflected in the toxicological properties of FPBO particle emissions, which showed less acute toxicity effects on the cell line than HFO combustion particles. The electrostatic precipitator used in the boiler plant efficiently removed flue gas particles of all sizes. Only minor differences in the toxicological properties of particles upstream and downstream of the electrostatic precipitator were observed, when the same particulate mass from both situations was given to the cells.

Increasing attention has been attracted in developing new technologies to remove chlorofene (CF) and dichlorofene (DCF), which were active agents in antimicrobials for general cleaning and disinfecting. This study investigated the significant influences of bicarbonate (HCO3−) on the degradation of CF and DCF in the Cu(II)-mediated Fenton-like system Cu2+/H2O2. Our results indicate that HCO3− may play a dual role to act 1) as a ligand to stabilize Cu(II), forming soluble [CuII(HCO3−)(S)]+ species to catalyze H2O2 producing hydroxyl radical (OH) and superoxide ion (O2−) and 2) as a OH scavenger. Furthermore, the reaction kinetics, mechanisms, and intermediates of CF and DCF were assessed. The apparent rate constants of CF and DCF were enhanced by a factor of 8.5 and 5.5, respectively, in the presence of HCO3− at the optimized concentration of 4 mM. Based on the intermediate identification and frontier electron densities (FEDs) calculations, the associated reaction pathways were tentatively proposed, including C–C scission, single or multiple hydroxylation, and coupling reaction. In addition, significant reduction in the aquatic toxicity of CF and DCF was observed after treatment with Cu2+/H2O2–HCO3- system, evaluated by Ecological Structure Activity Relationships (ECOSAR) program. These findings provide new insights into Cu(II)-mediated reactions to better understand the environmental fate of organic contaminants in carbonate-rich waters.

Pollution of marine environments with microplastic particles (i.e. plastic fragments <5 mm) has increased rapidly during the last decades. As these particles are mainly of terrestrial origin, coastal ecosystems such as coral reefs are particularly threatened. Recent studies revealed that microplastic ingestion can have adverse effects on marine invertebrates. However, little is known about its effects on small-polyp stony corals that are the main framework builders in coral reefs. The goal of this study is to characterise how different coral species I) respond to microplastic particles and whether the exposure might II) lead to health effects. Therefore, six small-polyp stony coral species belonging to the genera Acropora, Pocillopora, and Porites were exposed to microplastics (polyethylene, size 37–163 μm, concentration ca. 4000 particles L−1) over four weeks, and responses and effects on health were documented.The study showed that the corals responded differentially to microplastics. Cleaning mechanisms (direct interaction, mucus production) but also feeding interactions (i.e. interaction with mesenterial filaments, ingestion, and egestion) were observed. Additionally, passive contact through overgrowth was documented. In five of the six studied species, negative effects on health (i.e. bleaching and tissue necrosis) were reported.We here provide preliminary knowledge about coral-microplastic-interactions. The results call for further investigations of the effects of realistic microplastic concentrations on growth, reproduction, and survival of stony corals. This might lead to a better understanding of resilience capacities in coral reef ecosystems.

High-technology industries have grown continuously in Taiwan and elsewhere in the world. Volatile organic compounds (VOCs) comprise the highest percentage of emissions in these industries. The objectives of this study were to identify VOC sources and to apportion their contributions by using a three-step approach. These included estimating concentration distributions, performing principal component analysis (PCA), and mapping concentration contours. The results showed that the dominant compound groups were aromatic and aliphatic compounds. The PCA resolved four emission sources: vehicular traffic, industrial solvents, waste water plants, and cleaning/degreasing agents. Spatial distributions showed that concentrations of vehicular traffic-related compounds (benzene and isooctane) were highest at the entrances to the science park, and strongly related to traffic volume, and that the emissions of industry-related compounds (xylene and ethylbenzene) were closest to the associated sources. This study provided an accurate, practical and efficient method of characterizing emission sources in an industrial complex.

The built environs alter hydrology and water resource chemistry. Florida is subject to nutrient criteria and is promulgating “no-net-load-increase” criteria for runoff and constituents (nutrients and particulate matter, PM). With such criteria, green infrastructure, hydrologic restoration, indirect reuse and source control are potential design solutions. The study simulates runoff and constituent load control through urban source area re-design to provide long-term “no-net-load-increases”. A long-term continuous simulation of pre- and post-development response for an existing surface parking facility is quantified. Retrofits include a biofiltration area reactor (BAR) for hydrologic and denitrification control. A linear infiltration reactor (LIR) of cementitious permeable pavement (CPP) provides infiltration, adsorption and filtration. Pavement cleaning provided source control. Simulation of climate and source area data indicates re-design achieves “no-net-load-increases” at lower costs compared to standard construction. The retrofit system yields lower cost per nutrient load treated compared to Best Management Practices (BMPs).

China has one of the highest PM2.5 (particulate matter with an aerodynamic diameter smaller than 2.5 μm) pollution levels in the world. It might still be long before air quality reaches the National Class II standard of 35 μg/m3.We aim to estimate the potential reduction in premature mortality by reducing indoor PM2.5 levels in the Beijing-Tianjin-Hebei (BTH) region and compare it with reducing outdoor levels.We combined PM2.5 transport model and the Global Burden of Disease (2016) methodology to estimate potential reductions in premature mortality attributable to PM2.5 by reducing indoor PM2.5 to National Class I standard of 15 μg/m3, and compared with reducing outdoor PM2.5 to Government 2020 Interim target of 64 μg/m3 or National Class II standard of 35 μg/m3.A total of 74,000 (95% confidence interval (CI): 43,000–111,000) premature deaths were attributable to PM2.5 exposure in 2013. Thirty percent, or 22,000 (95% CI: 17,000–32,000) deaths, would have been averted if indoor PM2.5 had reached the National Class I standard. The benefit is greater than that from reaching the Government 2020 Interim target for outdoor PM2.5 [22%, or 16,000 (95% CI: 12,000–23,000), deaths], although still smaller than that from reaching the National Class II standard [42%, or 31,000 (95% CI: 24,000–45,000), deaths].Reaching the National Class I level of indoor PM2.5 at current outdoor pollution levels could bring considerable health benefits, which are comparable to those from reaching the Government 2020 Interim target for outdoor PM2.5.The avertable premature deaths gained from cleaning indoor PM2.5 to National Class I standard level would be greater than reducing outdoor PM2.5 to Government 2020 Interim target.

To investigate the effects of ambient-level gas-phase peroxides concurrent with O3 on foliar injury, photosynthesis, and biomass in herbaceous plants, we exposed Japanese radish (Raphanus sativus) to clean air, 50 ppb O3, 100 ppb O3, and 2-3 ppb peroxides + 50 ppb O3 in outdoor chambers. Compared with exposure to 100 ppb O3, exposure to 2-3 ppb peroxides + 50 ppb O3 induced greater damage in foliar injury, net photosynthetic rates and biomass; the pattern of foliar injury and the cause of net photosynthetic rate reduction also differed from those occurring with O3 exposure alone. These results indicate for the first time that sub-ppb peroxides + 50 ppb O3 can cause more severe damage to plants than 100 ppb O3, and that not only O3, but also peroxides, could be contributing to the herbaceous plant damage and forest decline observed in Japan's air-polluted urban and remote mountains areas.

Polyfluoroalkyl compounds (PFCs) are widely used in industry and consumer products. These products could end up finally in landfills where their leachates are a potential source for PFCs into the aqueous environment. In this study, samples of untreated and treated leachate from 22 landfill sites in Germany were analysed for 43 PFCs. ΣPFC concentrations ranged from 31 to 12,819 ng/L in untreated leachate and 4-8060 ng/L in treated leachate. The dominating compounds in untreated leachate were perfluorobutanoic acid (PFBA) (mean contribution 27%) and perfluorobutane sulfonate (PFBS) (24%). The discharge of PFCs into the aqueous environment depended on the cleaning treatment systems. Membrane treatments (reverse osmosis and nanofiltrations) and activated carbon released lower concentrations of PFCs into the environment than cleaning systems using wet air oxidation or only biological treatment. The mass flows of ∑PFCs into the aqueous environment ranged between 0.08 and 956 mg/day.

Biochar, a natural sourced carbon-rich material, has been used commonly in particle shape for carbon sequestration, soil fertility and environmental remediation. Here, we report a facile approach to fabricate freestanding biochar composite membranes for the first time. Wood biochars pyrolyzed at 300 °C and 700 °C were blended with polyvinylidene fluoride (PVdF) in three percentages (10%, 30% and 50%) to construct membranes through thermal phase inversion process. The resultant biochar composite membranes possess high mechanical strength and porous structure with uniform distribution of biochar particles throughout the membrane surface and cross-section. The membrane pure water flux was increased with B300 content (4825–5411 ± 21 L m⁻² h⁻¹) and B700 content (5823–6895 ± 72 L m⁻² h⁻¹). The membranes with B300 were more hydrophilic with higher surface free energy (58.84–60.31 mJ m⁻²) in comparison to B700 (56.32–51.91 mJ m⁻²). The biochar composite membranes indicated promising adsorption capacities (47–187 mg g⁻¹) to Rhodamine B (RhB) dye. The biochar membranes also exhibited high retention (74–93%) for E. coli bacterial suspensions through filtration. After simple physical cleaning, both the adsorption and sieving capabilities of the biochar composite membranes could be effectively recovered. Synergistic mechanisms of biochar/PVdF in the composite membrane are proposed to elucidate the high performance of the membrane in pollutant management. The multifunctional biochar composite membrane not only effectively prevent the problems caused by directly using biochar particle as sorbent but also can be produced in large scale, indicating great potential for practical applications.

Bioremediation of polycyclic aromatic hydrocarbon (PAH)-contaminated soils requires a higher microbial viability and an increased PAH bioavailability. The clay/modified clay-modulated bacterial degradation could deliver a more efficient removal of PAHs in soils depending on the bioavailability of the compounds. In this study, we modified clay minerals (smectite and palygorskite) with mild acid (HCl) and alkali (NaOH) treatments (0.5–3 M), which increased the surface area and pore volume of the products, and removed the impurities without collapsing the crystalline structure of clay minerals. In soil incubation studies, supplements with the clay products increased bacterial growth in the order: 0.5 M HCl ≥ unmodified ≥0.5 M NaOH ≥3 M NaOH ≥3 M HCl for smectite, and 0.5 M HCl ≥3 M NaOH ≥0.5 M NaOH ≥3 M HCl ≥ unmodified for palygorskite. A14C-tracing study showed that the mild acid/alkali-treated clay products increased the PAH biodegradation (5–8%) in the order of 0.5 M HCl ≥ unmodified > 3 M NaOH ≥ 0.5 M NaOH for smectite, and 0.5 M HCl > 0.5 M NaOH ≥ unmodified ≥ 3 M NaOH for palygorskite. The biodegradation was correlated (r = 0.81) with the bioavailable fraction of PAHs and microbial growth as affected particularly by the 0.5 M HCl and 0.5 M NaOH-treated clay minerals. These results could be pivotal in developing a clay-modulated bioremediation technology for cleaning up PAH-contaminated soils and sediments in the field.