Gaseous and particulate polycyclic aromatic hydrocarbons (PAHs) and size-segregated particulate matter (PM) in indoor air and outdoor air, along with personal exposure, were monitored in rural households of Northern China. The daily average concentrations of 28 species were 1310 ± 811, 738 ± 321, 465 ± 247, and 655 ± 250 ng/m3 in kitchen air, bedroom air, and outdoor air, and for personal exposure, respectively. PAHs tended to occur in the particulate phase with increasing molecular weight. Absorption by particulate organic carbon was dominant in the gas-particle partitioning process. The daily averaged concentrations of PM2.5 and PM1.0 were 104 ± 39.5 and 88.4 ± 39.3 μg/m3 in kitchen air, 79.0 ± 63.2 and 65.7 ± 57.5 μg/m3 in bedroom air, 52.9 ± 16.5 and 41.5 ± 12.5 μg/m3 in outdoor air, and 71.7 ± 30.8 and 61.5 ± 28.4 μg/m3 for personal exposure, respectively. The non-priority components contributed 5.5 ± 2.8% to the total PAHs, while their fraction of carcinogenic risk reached 85.6 ± 6.9%. The mean cancer risk posed to rural residents via inhalation exposure to PAHs exceeded the current acceptable threshold of 1.0 × 10−6 and the national average estimated in China. The personal exposure levels of PAHs and PM in households using clean energy were lower than those in households using traditional biomass by 30.0%, 29.4%, and 38.5% for PAH28, PM2.5, and PM1.0, respectively. However, the cancer risk of personal inhalation exposure to PAH28 from using liquid petroleum gas (LPG) was higher than that from using firewood, implying the adoption of LPG may not effectively reduce the cancer risk despite the decreasing exposure levels of PAH28 and PM with respect to the use of firewood. Cooking individuals suffered higher exposure levels of PAH28 and PM1.0 compared with non-cooking individuals, and the cancer risk of personal inhalation exposure to PAH28 for cooking individuals was 1.7 times that for non-cooking individuals. Cooking was a critical factor that affected the personal exposure levels of the local male and female residents.

The 6:2 chlorinated polyfluoroalkyl ether sulfonic acids (6:2 Cl-PFAES), 2,3,3,3-tetrafluoro-2-(1,1,2,2,3,3,3-heptafluoropropoxy)-propanoic acid (HFPO-DA) and perfluoroethylcyclohexane sulfonate (PFECHS) are emerging per- and polyfluoroalkyl substances (PFASs) that are being applied to replace phased-out PFASs, which have high persistency, high bioaccumulation potential and high toxicity. Recently, these emerging PFASs were observed in estuary and marine areas with a pollution level of ng/L. In this study, three levels (10 ng L⁻¹, 100 ng L⁻¹ and 1000 ng L⁻¹) for these PFASs were selected to investigate the response of marine Chlorella sp. to 14 days of exposure. The growth of Chlorella sp. was significantly inhibited by each PFAS over time. Treatments with 1000 ng/L exposure caused the most severe reduction in growth for each PFAS treatment. For the first half of the experimental period (from Day 0 to Day 6), the influence of each PFAS was not significant (p > 0.05). However, treatments with all concentrations of 6:2 Cl-PFAES, HFPO-DA and 1000 ng L⁻¹ PFECHS significantly reduced the growth of Chlorella sp. from Day 8. The superoxide dismutase (SOD) activities in Chlorella sp. were significantly increased (p < 0.05) when exposed to 6:2 Cl-PFAES, HFPO-DA and PFECHS. The catalase (CAT) and peroxidase (POD) activities in Chlorella sp. were significantly inhibited (p < 0.05) by each PFAS. The glutathione (GSH) contents in Chlorella sp. were significantly increased by each PFAS. However, the increases in GSH concentration in Chlorella sp. were low. The inhibition of algal growth was primarily due to the reduction of the activities of CAT and POD. PFECHS had the lowest toxicity among the three PFASs, and it induced less oxidized damage to Chlorella sp. In conclusion, as alternatives to phased-out PFASs, the emerging PFASs are not safe in aquatic environment, and attention should be paid to the management and restriction of these emerging PFASs.

Growth of textile industries led to production of enormous dye varieties. These textile dyes are largely used, chemically stable and easy to synthesize. But they are recalcitrant and persist as less biodegradable pollutants when discharged into waterbodies. Potential use of enzyme-linked bioremediation of textile dyes will control their toxicity in waterbodies. Bioinformatics and Molecular docking tool provides an insight into remediation mechanism by predicting susceptibility of dye degradation using oxidoreductive enzymes. In this study, six dyes, Reactive Red F3B, Remazol Red RGB, Joyfix Red RB, Joyfix Yellow MR, Remazol Blue RGB and Turquoise CL-5B of azo, anthraquinone and phthalocyanine molecular class were identified as potential targets for degradation by laccase and azoreductase of Aeromonas hydrophila in addition to Lysinibacillus sphaericus through in silico docking tool BioSolveIT-FlexX. Azoreductase breaks azo bonds by ping-pong mechanism whereas laccase decolorizes dyes by free radical mechanism which is not specific in nature. Results were analyzed based on parameters like stability, catalytic action and selectivity for enzyme-dye interactions. Amino acids of enzymes interacted with several dyes substantiating variations in active site for enzyme-ligand binding affinity. This suggests the role of enzymes in decolorizing an extensive variety of textile dyes, thereby, aiding in understanding the enzyme mechanisms in Bioremediation.

Concentrations of unsubstituted and methylated polycyclic aromatic hydrocarbons (PAHs and Me-PAHs) were examined in road dusts from some representative areas with different land-use types in northern Vietnam, providing updated information about the occurrence, sources, and risks of these pollutants in Southeast Asian region. The Vietnamese road dusts were contaminated with low to moderate levels of PAHs and Me-PAHs as compared to those from other countries in the world. Concentrations of PAHs and Me-PAHs (Σ34PAHs) decreased in the order: urban (median 1800; range 1100–5500) ≈ industrial (1300; 550–10,000) > suburban (450; 310–1300) ≈ rural road dust (330; 210–2300 ng g⁻¹), suggesting an urban-rural declining trend and effects of urbanization-industrialization processes in PAH emission extent in Vietnam. The profiles and diagnostic ratios of PAHs and Me-PAHs in our samples revealed that these compounds were mainly derived from pyrogenic sources rather than petrogenic sources. Traffic emissions (e.g., vehicle exhaust, tire debris, and possible leaks of fuels, oils, and lubricants) were estimated as principal sources of PAHs and Me-PAHs, especially in the urban and industrial areas. Other pyrogenic sources (e.g., coal, wood, and biomass combustion) were also existed in the industrial, suburban, and rural areas, reflecting PAH origins from thermal industrial processes, open burning of agricultural by-products, and domestic energy utilization. Persons working outdoors and children in the urban and industrial areas were estimated to receive higher intake doses of PAHs and Me-PAHs, which were one to two orders of magnitude higher than those estimated for other groups. Except for potential cancer risk estimated for the occupational groups in the industrial area under the worst exposure scenarios, the non-cancer and cancer risk levels were generally acceptable; however, more comprehensive risk assessment considering other exposure pathways (e.g., inhalation and diet) is needed.

In this study, various remote sensing data, modeling data and emission inventories were integrated to analyze the tempo-spatial distribution of biomass burning in mainland Southeast Asia and its effects on the local ambient air quality from 2001 to 2016. Land cover changes have been considered in dividing the biomass burning into four types: forest fires, shrubland fires, crop residue burning and other fires. The results show that the monthly average number of fire spots peaked at 34,512 in March and that the monthly variation followed a seasonal pattern, which was closely related to precipitation and farming activities. The four types of biomass burning fires presented different tempo-spatial distributions. Moreover, the monthly Aerosol Optical Depth (AOD), concentration of particulate matter with a diameter less than 2.5 μm (PM₂.₅) and carbon monoxide (CO) total column also peaked in March with values of 0.62, 45 μg/m³ and 3.25 × 10¹⁸ molecules/cm², respectively. There are significant correlations between the monthly means of AOD (r = 0.74, P < 0.001), PM₂.₅ concentration (r = 0.88, P < 0.001), and CO total column (r = 0.82, P < 0.001) and the number of fire spots in the fire season. We used Positive Matrix Factorization (PMF) model to resolve the sources of PM₂.₅ into 3 factors. The result indicated that the largest contribution (48%) to annual average concentration of PM₂.₅ was from Factor 1 (dominated by biomass burning), followed by 27% from Factor 3 (dominated by anthropogenic emission), and 25% from Factor 2 (long-range transport/local nature source). The annually anthropogenic emission of CO and PM₂.₅ from 2001 to 2012 and the monthly emission from the Emission Database for Global Atmosphere Research (EDGAR) were consistent with PMF analysis and further prove that biomass burning is the dominant cause of the variation in the local air quality in mainland Southeast Asia.

Lipophilic marine algal toxins (LMATs) pose a potential threat to the health of marine shellfish consumers and marine breeding industries. In this study, LMATs in dissolved phases (DP) and particulate phases (PP) in the seawater of Jiaozhou Bay were accurately determined over four seasons to understand their composition, level, phase partitioning, spatiotemporal variation, and potential sources in aquatic environments of a typical semi-closed mariculture bay. Various LMATs, such as okadaic acid (OA), dinophysistoxin-1 (DTX1), dinophysistoxin-2 (DTX2), gymnodimine (GYM), 13-desmethyl spirolide C (SPX1), pectenotoxin-2 (PTX2), pectenotoxin-2 seco acid (PTX2 SA), and pectenotoxin-11 (PTX11), were detected in DP and PP; of these, OA and PTX2 were the dominant LMATs in DP and PP, respectively. The average proportion of ΣLMATs in DP (97.5%) was significantly higher than that in PP (2.5%), which indicates that LMATs are predominantly partitioned into DP. The total concentrations of LMATs in DP ranged from 4.16 ng/L to 23.19 ng/L (mean, 13.35 ng/L) over four seasons. The highest levels of LMATs in DP and PP were found in summer (mean, 16.71 ng/L) and spring, respectively, while the maximum variety of LMATs was found in autumn. This result suggests that seasonal changes could influence the composition, concentration, and phase partitioning of LMATs in aquatic environments of a coastal semi-closed mariculture bay. ΣLMAT concentrations were higher in the western region than in the eastern region of the bay, where shellfish may have a greater risk of exposure. Dinophysis acuminata, Dinophysis fortii, and Prorocentrum minimum were the potential sources of LMATs in the aquaculture seawater. Overall, various LMATs occurred in the semi-closed mariculture bay, and the persistence and bioavailability of these toxins in aquaculture seawater should be determined in future research.

Metals are among the most toxic pollutants in urban stormwater. To investigate the concentration of dissolved and particulate fractions, the temporal variation during rain events, the effect of wash-off surface, and to assess the pollution status of metals in urban runoff, a total of 155 samples were collected mainly from trafficked areas, roofs and parking lots in Beijing from March to November 2015. Most of the metals were found mainly in the particulate fraction (68–96%) from trafficked surfaces, while for roof runoff Cd, Fe, Mn and Zn were found more equally in dissolved and particulate fractions. Metal concentrations were higher during start of a rain event than later (p < 0.05), and also were higher the longer the period of antecedent dry days. The mean concentration of all metals in trafficked areas exceeded both the Chinese standard Level III (swimming and fishery waters) and the European standards (surface water). Mean concentrations of Cd, Mn, Zn, Al, Fe, Pb and Ni from trafficked areas were 2–10 times higher due to higher traffic intensity and substantial atmospheric deposition, while Sb was 20 times higher than in any other reported data for urban runoff. Cluster analysis (CA) and principal component analysis (PCA) together with Pearson's correlation co-efficient suggested that Cd, Cr, Cu, Mn, Ni, Pb, and Zn mainly originates from vehicular activities, while Mn and Zn in roof runoff is due to atmospheric deposition. The geo-accumulation and pollution indices show that runoff from trafficked areas are moderately to heavily polluted by most metals, except Cu and Zn. Thus, Beijing urban runoff presents an environmental risk towards lakes, bathing water and drinking water. The results can be used as basis for development of stormwater and pollution control strategies.

Indoor and outdoor fine particulate matter (PM2.5) are both leading risk factors for death and disease, but making indoor measurements is often infeasible for large study populations.We developed models to predict indoor PM2.5 concentrations for pregnant women who were part of a randomized controlled trial of portable air cleaners in Ulaanbaatar, Mongolia. We used multiple linear regression (MLR) and random forest regression (RFR) to model indoor PM2.5 concentrations with 447 independent 7-day PM2.5 measurements and 87 potential predictor variables obtained from outdoor monitoring data, questionnaires, home assessments, and geographic data sets. We also developed blended models that combined the MLR and RFR approaches. All models were evaluated in a 10-fold cross-validation.The predictors in the MLR model were season, outdoor PM2.5 concentration, the number of air cleaners deployed, and the density of gers (traditional felt-lined yurts) surrounding the apartments. MLR and RFR had similar performance in cross-validation (R2 = 50.2%, R2 = 48.9% respectively). The blended MLR model that included RFR predictions had the best performance (cross validation R2 = 81.5%). Intervention status alone explained only 6.0% of the variation in indoor PM2.5 concentrations.We predicted a moderate amount of variation in indoor PM2.5 concentrations using easily obtained predictor variables and the models explained substantially more variation than intervention status alone. While RFR shows promise for modelling indoor concentrations, our results highlight the importance of out-of-sample validation when evaluating model performance. We also demonstrate the improved performance of blended MLR/RFR models in predicting indoor air pollution.

Constructed wetlands are an environmentally friendly and economically efficient sewage treatment technology, with fillers playing an important role in treatment processes. However, traditional wetland fillers (e.g. zeolite) are known to be imperfect because of their low adsorption capacity. In this paper, the adsorbent sodium titanate nano fillers (T3-F) was synthesized as an alternative to traditional filler with sodium titanate nanofibers (T3) as the raw material, epoxy adhesive as the adhesive agent and NH₄HCO₃ as the pore-making agent. The properties of T3-F were characterized by powder X-ray diffraction (XRD), scanning electron microscope-energy dispersive X-ray spectroscopy (SEM-EDX), porosity. The effect of different parameters such as pH, co-existing ions, contact time, initial metal ion concentrations and temperature was investigated for heavy metal adsorption. The results showed that the adsorption of heavy metal by T3-F followed the pseudo-second-order kinetic and Langmuir isotherm models. The maximum adsorption capacities for Cu²⁺, Pb²⁺, Zn²⁺, Cd²⁺ were about 1.5–1.98 mmol/g, which were 4–5 times that of zeolite, the traditional commonly used filler. Moreover, T3-F could entrap toxic ions irreversibly and maintain structural stability in the adsorption process, which solved the issue of secondary pollution. In the presence of competing ions, the adsorption efficiency for Pb²⁺ was not reduced significantly. Adsorption was strongest at high pH. From the results and characterization, an adsorption mechanism was suggested. This study lays a foundation for the practical application of T3-F as a constructed wetland filler in the future.

The concentrations, congener profiles and spatial distribution of 13 phthalate esters (PAEs) in the freshwater fish ponds in the Pearl River Delta (PRD) region were investigated in water and sediment samples collect from 22 sites during Jul. 2016–Sept. 2017. The di-2-ethylhexyl phthalate (DEHP) was the predominant compounds in both water and sediment samples, accounting for 70.1% and 66.1% of ∑PAEs, respectively. The DEHP concentrations in the water samples collected from the sites of Zhongshan (35.7 μg/L), Jingmen (17.3 μg/L) and Nanhai (14.2 μg/L) were higher than that collected from other sampling sites (p <0.05), and exceed the Chinese environmental quality standards for surface water (DEHP, 8.00 μg/L). The concentrations of ΣPAEs (mean and median were 11.8 mg/kg dw and 7.95 mg/kg dw) in sediment was higher than that in sediment of river and estuary in the PRD region (p <0.05). The median concentrations of DEHP and di-n-butyl phthalate (DBP) exceeded recommend environmental risk limit (ERL) that posed a potential risk to the aquaculture fish pond environment in the PRD.