Chlorinated hydrocarbons are the most common organic pollutants in groundwater systems worldwide. In this study, we developed bio-beads with immobilized anaerobic bacteria, zero-valent iron (ZVI), and activated carbon (AC) powder and evaluated their efficacy in removing 1,1,1-trichloroethane (TCA) from groundwater. Bio-beads were produced by polyvinyl alcohol, alginate, and AC powder. We found that the concentration of AC powder used significantly affected the mechanical properties of immobilized bio-beads and that 1.0 % (w/v) was the optimal concentration. The bio-beads effectively degraded TCA (160 mg L⁻¹) in the anaerobic medium and could be reused up to six times. The TCA degradation rate of bio-beads was 1.5 and 2.3 times greater, respectively, than ZVI + AC treatment or microbes + AC treatment. Measuring FeS produced by microbial reactions indicated that TCA removal occurred via FeS-catalyzed dechlorination. Analysis of clonal libraries derived from bio-beads demonstrated that the dominant species in the community were Betaproteobacteria and Gammaproteobacteria, which may contribute to the long-term stability of ZVI reactivity during TCA dechlorination. This study shows that the combined use of immobilized anaerobic bacteria, ZVI, and AC in bio-beads is effective and practical for TCA dechlorination and suggests they may be applicable towards developing a groundwater treatment system for the removal of TCA.

A new method for the degradation of bisphenol A (BPA) in aqueous solution was developed. The oxidative degradation characteristics of BPA in a heterogeneous Fenton reaction catalyzed by Fe₃O₄/graphite oxide (GO) were studied. Transmission electron microscopic images showed that the Fe₃O₄nanoparticles were evenly distributed and were ∼6 nm in diameter. Experimental results suggested that BPA conversion was affected by several factors, such as the loading amount of Fe₃O₄/GO, pH, and initial H₂O₂concentration. In the system with 1.0 g L⁻¹of Fe₃O₄/GO and 20 mmol L⁻¹of H₂O₂, almost 90 % of BPA (20 mg L⁻¹) was degraded within 6 h at pH 6.0. Based on the degradation products identified by GC–MS, the degradation pathways of BPA were proposed. In addition, the reused catalyst Fe₃O₄/GO still retained its catalytic activity after three cycles, indicating that Fe₃O₄/GO had good stability and reusability. These results demonstrated that the heterogeneous Fenton reaction catalyzed by Fe₃O₄/GO is a promising advanced oxidation technology for the treatment of wastewater containing BPA.

Several studies have shown an increase in PCB sources in Africa due to leakage and wrongly disposed transformers, continuing import of e-waste from countries of the North, shipwreck, and biomass burning. Techniques used in the recycling of waste such as melting and open burning to recover precious metals make PCBs contained in waste and other semivolatile organic substances prone to volatilization, which has resulted in an increase of PCB levels in air, blood, breast milk, and fish in several regions of Africa. Consequences for workers performing these activities without adequate measures of protection could result in adverse human health effects. Recent biodegradation studies in Africa have revealed the existence of exotic bacterial strains exhibiting unique and unusual PCB metabolic capability in terms of array of congeners that can serve as carbon source and diversity of congeners attacked, marking considerable progress in the development of effective bioremediation strategies for PCB-contaminated matrices such as sediments and soils in tropical regions. Action must be taken to find and deal with the major African sources of these pollutants. The precise sources of the PCB plume should be pinned down and used to complete the pollutant inventories of African countries. These nations must then be helped to safely dispose of the potentially dangerous chemicals.

Ammonia (NH₃) is an important base gas and can react with acidic species to form atmospheric aerosols. Due to the rapid growth of poultry and swine production in the North Carolina Coastal Plain, atmospheric NH₃concentrations across the region have subsequently increased. Ammonia concentrations and inorganic particulate matter (PM) at four ambient stations in the vicinity of an egg production facility were measured for 1 year using PM₂.₅speciation samplers with honeycomb denuders and ion chromatography (IC). Meanwhile, concentrations of NH₃and inorganic PM in one of the egg production houses were also simultaneously measured using a gas analyzer for NH₃and the filter pack plus IC method for inorganic PM. An equilibrium model-ISORROPIA II was applied to predict the behavior of inorganic aerosols in response to precursor gas concentrations and environmental parameters. Average ambient NH₃concentrations varied from 10.0 to 27.0 μg/m³, and they were negatively correlated with the distances from the ambient location to the nearest egg production house exhausts. Ambient NH₃concentrations were higher in warm seasons than in cold seasons. Measured NH₃concentrations agreed well with ISORROPIA II model predictions at all sampling stations. For the ambient stations, there was a good agreement in particle phase NH₄⁺between the model simulation and observations. For the in-house station, the model simulation was applied to correct the overestimation of particle phase NH₄⁺due to gas phase NH₃breaking through the denuders. Changes in SO₄²⁻, NO₃⁻, and Cl⁻yield proportional changes in inorganic PM mass. Due to the abundance of NH₃gas in the vicinity area of the monitored farm, changes in NH₃concentrations had a small effect on inorganic PM mass. Aerosol equilibrium modeling may be used to assess the influence of precursor gas concentrations on inorganic PM formation when the measurements for some species are unavailable.

Many studies have focused their attention on the determination of elements of toxicological and environmental interest in atmospheric particulate matter using analytical techniques requiring chemical treatments. The instrumental nuclear activation analysis technique allows achieving high sensitivity, good precision, and excellent limit of detection without pretreatment, also considering the problems related to the radioisotope characteristics (e.g., half-life time, interfering reactions, spectral interferences). In this paper, elements such as Al, As, Br, Cl, Cu, I, La, Mg, Mn, Na, Sb, Si, Ti, and V are studied in atmospheric PM₁₀sampled in downtown Rome: The relative radionuclides after activation of the sample are characterized by very short (ranging from 2.24 to 37.2 min) and short (ranging from 2.58 h to 2.70 days) half-lives. Furthermore, As, Br, La, Mn, and Sb were also determined for evaluating the aerosol characteristics. The results, elaborated considering the matrix effects and the interfering reaction contribution to the radioisotope formation (e.g.,²⁸Al generated by both (n,γ) reaction from²⁷Al and (n,p) reaction from²⁸Si), show interesting values of As (0.3–6.1 ng m⁻³), Cu (22–313 ng m⁻³), Mn (17–125 ng m⁻³), V (7–63 ng m⁻³), higher than those determined in an area not influenced by autovehicular traffic, and significant levels of I (1–11 ng m⁻³) and Ti (25–659 ng m⁻³) in Rome PM₁₀. The other elements show a pattern similar to the very few data present in the literature. It should be underlined the good correlation (r²) of Al vs. Mg (0.915) and Al vs. La (0.726), indicating a same sources for these species as well as Br–Sb showing a little lower correlation (0.623). This last hypothesis is confirmed by the study of the enrichment factors: Sb and Br may be attributed to anthropogenic sources; Cu, Cl, and I show a mixed origin (natural and anthropogenic), whereas Al, Si, Ti, Mn, Na, Mg, and As are of crustal origin. For having more information, a statistical approach based on the principal component analysis and the canonical discriminant analysis has been performed: All the samples (except one) are grouped in a cluster, and elements such as As, Br, Cu, I, La, Mn, Sb, Ti, and V are highly correlated, whereas Na and Cl and Mg and Al assemble in two different clusters. Finally, a comparison with other similar studies is reported showing interesting values for Al, As, Mg, Mn, and Ti.

Changes in the characteristics of algae-derived organic matter (AOM) were examined upon the operation of a microbial fuel cell (MFC) using multiple analytical methods. Temporal variations in the UV absorption and fluorescence excitation–emission matrix of the AOM revealed that less condensed humic-like components and large-sized protein-like fluorescent compounds were preferentially decomposed over the period of electricity generation. They also showed that low UV-absorbing extracellular organic matters (EOM) were produced at the end of the operation. SEC chromatograms demonstrated that smaller-sized UV-absorbing components were initially decomposed, followed by the net production of EOM with an intermediate molecular weight. Fourier transform infrared (FT-IR) spectra showed that proteins and polysaccharides were the two most dominant structures of the AOM in the MFC. Two-dimensional correlation spectroscopy combined with FT-IR provided additional valuable information on the sequential changes of the AOM, which occurred in the order of proteins → acidic functional groups → polysaccharides → amino acids/proteins.

Produced water (PW) is the largest waste stream generated in oil and gas industries. The drilling and extraction operations that are aimed to maximize the production of oil may be counterbalanced by the huge production of contaminated water (called PW) with pollutants, such as heavy metals, dissolved/suspended solids, and organic compounds. PW is conventionally treated through different physical, chemical, and biological methods. In offshore platforms, because of space constraints, compact physical and chemical systems are used. However, major research efforts are being developed with innovative technologies for treating PW in order to comply with reuse and discharge limits. Among them, electrochemical technologies have been proposed as a promising alternative for the treatment of this kind of wastewaters. Then, this paper presents a minireview of efficient electrochemical technologies used until now for treating PW generated by petrochemical industry.

Air quality in urban areas attracts great attention due to increasing pollutant emissions and their negative effects on human health and environment. Numerous studies, such as those by Mouilleau and Champassith (J Loss Prevent Proc 22(3): 316–323, 2009), Xie et al. (J Hydrodyn 21(1): 108–117, 2009), and Yassin (Environ Sci Pollut Res 20(6): 3975–3988, 2013) focus on the air pollutant dispersion with no buoyancy effect or weak buoyancy effect. A few studies, such as those by Hu et al. (J Hazard Mater 166(1): 394–406, 2009; J Hazard Mater 192(3): 940–948, 2011; J Civ Eng Manag (2013)) focus on the fire-induced dispersion of pollutants with heat buoyancy release rate in the range from 0.5 to 20 MW. However, the air pollution source might very often be concentrated and intensive, as a consequence of the hazardous materials fire. Namely, transportation of fuel through urban areas occurs regularly, because it is often impossible to find alternative supply routes. It is accompanied with the risk of fire accident occurrences. Accident prevention strategies require analysis of the worst scenarios in which fire products jeopardize the exposed population and environment. The aim of this article is to analyze the impact of wind flow on air pollution and human vulnerability to fire products in a street canyon. For simulation of the gasoline tanker truck fire as a result of a multivehicle accident, computational fluid dynamics large eddy simulation method has been used. Numerical results show that the fire products flow vertically upward, without touching the walls of the buildings in the absence of wind. However, when the wind velocity reaches the critical value, the products touch the walls of the buildings on both sides of the street canyon. The concentrations of carbon monoxide and soot decrease, whereas carbon dioxide concentration increases with the rise of height above the street canyon ground level. The longitudinal concentration of the pollutants inside the street increases with the rise of the wind velocity at the roof level of the street canyon.

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.