In order to ensure radiation monitoring and protection, investigation and assessment of radiological risks that may be associated with the consumption of packaged table waters commonly consumed in Ogbomoso and Ilorin metropolis, Nigeria, was carried out. The measurements were carried out using a ‘3 x 3’ inch lead-shielded NaI (Tl) detector coupled through coaxial cable to a multichannel analyser. The measured activity concentrations of the natural radionuclides in the packaged drinking water sample are mostly within the recommended limits. The estimated mean Annual Effective Dose was found to be within the acceptable limits of 1 mSv/y for the general populace except for the infants which is slightly higher for some of the samples. The estimated Excess Lifetime Cancer Risk were found to be lower than the world average value of 0.2 x 10-3 in only two of the selected packaged drinking water. This implies the possibility of developing cancer over a lifetime considering seventy years as the average life span is considerably high.

The ability of fungi to act as bio-sorbent had been extensively evaluated and has shown excellent metal sequestering ability for heavy metals such as cadmium, copper, zinc, lead, iron, nickel, radium, thorium, and uranium from aqueous solution. In the present study, tolerance, removal efficiency and adsorption capacity of hexavalent chromium using isolated fungal strains were analysed. Total nine fungal isolates were obtained from organic pollutants and metals contaminated Gujarat Industrial Development Cooperation sites. Filamentous fungi isolated belonged to Aspergillus spp., Rhizopus spp., Trichoderma spp., and Penicillium spp. Chromium sorption experiments using isolated fungal strains were carried out to check adsorption capacity and adsorption intensity. At higher chromium concentration, removal efficiency and adsorption capacity were observed in the order of Aspergills candidus > Aspergillus ochraceus > Aspergillus flavus > Rhizopus spp. > Trichoderma spp. A. candidus showed higher adsorption capacity, 5.49mg/g with 98.75% chromium removal efficiency at 150ppm of hexavalent chromium. The observed RL value for Langmuir isotherm for all the three concentrations was less than 1, depicting favourable sorption and in Freundlich isotherm, the value of 1/n exceeds more than 1 showing co-operative or similar type of adsorption.

Atmospheric aerosols are very crucial from air pollution and health perspective as well as for regional and global climate. This paper attempts to summarize the aerosol loading and their properties such as Aerosol Optical Depth (AOD), Single Scattering Albedo (SSA), Angstrom exponent, and Radiative forcing, over India. All the above mentioned parameters have shown significant variability with change in the site and season. From various studies it was observed that AOD is relatively higher over Northern part of India as compared to Southern and Eastern part. Generally, lower values of SSA were observed over all sites during winter and post-monsoon seasons which indicates the dominance of absorbing type aerosol during these seasons. Also the ARF within atmosphere showed comparatively higher values during November-December and lower value during August and September all over the India. The current state of knowledge about aerosol sources, interactions and their effects on environment is limited because of its complexity. Therefore, more focused research in needed to understand the aerosol’s role in climatic phenomenon.

A large anthropogenic source of mercury pollution is mercury-dependent artisanal and small-scale gold mining (ASGM). Thabeikkyin Township is a small-scale gold mining township located in Pyin Oo Lwin District in the Mandalay Region, Myanmar. The villages of Thabeikkyin Township engage in gold ore crushing, screening, refining, and other mining activities for a living. Miners in this area commonly use mercury for gold recovery by heating amalgam at their homes, gold shops, on the street, and near the riverbank. The evaporated mercury is released into the atmosphere during the heating process and then transported and deposited in the surrounding environments, resulting in the mercury pollution of air, water, soil, etc. To assess atmospheric mercury pollution, a preliminary study on the environmental mercury contamination from ASGM was conducted in Thabeikkyin Township. High mercury concentrations were observed in plant samples collected near the refining sites, ranging 0.33–6.51 ug/g, compared with 0.02 ug/g in Wet Thay Village, where no mercury use was reported. Correlation coefficients between Hg and other heavy metals showed that no heavy metal concentration significantly correlated with that of Hg. The results indicated that the atmospheric environment in the ASGM area of Thabeikkyin Township was contaminated with mercury originating from ASGM, which could very likely deteriorate the health of surrounding residents.

The increased consumption of fossil fuels provokes high levels of carbon dioxide (CO2) emissions, which give rise to serious environmental issues. Accordingly, designing and utilizing new classes of materials, such as Schiff bases, to capture CO2 gained significant attention from researchers worldwide. In the present work, two Schiff bases were synthesized and examined as storage materials for carbon dioxide gas. The prepared compounds were obtained by reacting trimethoprim with two aldehydes severally (benzaldehyde and parabromobenzaldehyde) in boiling methanol. The surface morphology of the compounds was investigated via field emission scanning electron microscopy (FESEM). The Brunauer-Emmett-Teller (BET) test showed that Schiff bases 1 and 2 have surface areas of 17.993 and 2.732 m2/g, pore volumes of 0.008 and 0.005 cm3/g, and pore diameters of 17.02 and 74.89 nm, respectively. Reasonable uptake values of CO2 (31.36 cm3/g, 6.2 wt%) and (25.30 cm3/g, 5.0 wt%) were achieved by the prepared Schiff bases 1 and 2, respectively, at 313 K temperature and 40 bars pressure.

Saraca asoca bark has long been used in traditional Indian medicine. Considering its low cost and non-toxic nature, it can find application as a biosorbent. This article explores the application of Saraca asoca bark powder (SABP) for biosorption of hexavalent chromium. Various analytical techniques including Field emission scanning electron microscope (FESEM) attached with energy dispersive spectrometer (EDS), Fourier transform infrared spectroscopy (FTIR) and point of zero charge (pHpzc) were adopted in order to identify the physico-chemical features of SABP. Factors such as pH (2-8), contact time (for 3 hours), initial Cr (VI) concentration (10 – 250 mg/l) and temperature (15 - 35°C) were examined for their influence on Cr (VI) biosorption via batch studies. Biosorption data clearly followed Redlich-Peterson isotherm model as compared to Langmuir and Freundlich models. The Langmuir monolayer adsorption capacities (Qm) at 15, 25 and 35°C were 123.4, 125.0 and 175.4 mg/g respectively. Biosorption followed pseudo-second-order kinetics and the mechanism of diffusion was governed by both surface sorption and pore diffusion as demonstrated by the plot for Intraparticle diffusion model and the pore diffusion coefficient (Dp~10-9 cm2/s). The nature of biosorption was found to be spontaneous and endothermic as reflected through various thermodynamic parameters such as the free energy change (ΔG = -3.0 to -3.7 kJ/mol), entropy change (ΔS = 37.8 J/K/mol) and enthalpy change (ΔH = 7.9 kJ/mol). The study recommends that SABP may be utilized as a potential biosorbent for Cr(VI) ions.

In this work, Fe3O4-SiO2 nanoparticles were synthesized, characterized, and applied as adsorbent material to remove methyl blue stain from an aqueous solution. The prepared nanoparticles were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and Brunauer–Emmett–Teller (BET) to determine the physical surface properties and correlate them to the adsorption efficiency. In addition, this study investigated the influence of several parameters on the removal percentage and adsorption capacity. Specifically, this study investigated the impact of changing the following parameters: pH (1 – 8), agitation speed (Uspeed; 100 - 350 rpm), initial methyl blue (MB) concentration (1 - 100 mg/L), adsorbent dose (0.05 to 0.15 g), and contact time (10 - 100 min). The characterization study reveals that the prepared material has an excellent surface area (385 ± 5 m2/g) and pore volume (0.31 cm3/g) which enhances the adsorption capacity. In addition, the prepared material showed excellent efficiency where the removal percentage reached 99.0±1% at the optimal operating conditions and the maximum adsorption capacity was 40 mg/g. This study delivers a full elucidation of the adsorption of MB dye by Fe3O4-SiO2 NPs which considers a promising inexpensive adsorbent. It also delivers important insight information about the adsorption process and the influence of each parameter, which fill the lack in this field.

Cities in developing countries like Shiraz in Iran face significant challenges due to a lack of an integrated solid waste management system. Climate change, soil, and water pollution are examples of environmental issues caused by improper Municipal Solid Waste Management Systems (MSWMS) in developing countries. The aim of this study is to find solutions for these environmental problems based on the experiences of developed countries. The data was collected using several methods such as visual observations, studying accessible documents of the current situation of the MSWMS in Shiraz, and participating in an interview with engineers the 'Shiraz Municipality Waste Management Organization' (SMWMO).  Results present the current functional elements of MSWMS in Shiraz, Shiraz waste diversion rate (0.22), and its Zero Waste Index (.015). Moreover, the results present some recommendations to find a way to transform cities like Shiraz into zero-waste cities. Results indicate that establishing zero-waste policies, legal frameworks, and financial strategies as well as convincing private sector involvements in installing waste-to-energy facilities and a proper sanitary landfill to move the city toward optimum recycling and zero landfilling in addition to reducing consumption and maximizing diversion rate and finally sustainable development by the cooperation of government, NGOs and media programs would solve many problems of the MSWMS and would solve environmental issues in many cities.

This research evaluates dibenzothiophene (DBT) adsorptive removal from the liquid stream on the graphitic carbon nitride (GCN) as a synthesized adsorbent at 25 0C with 3 g for 600 min. The morphological properties of GCN have been investigated by Brunauer–Emmett–Teller (BET), Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), and X-ray Diffraction (XRD). The study of the characteristic properties of nano adsorbent proves the suitability of the synthesized GCN in mercaptan adsorption process with the obtained data showing a good agreement with Freundlich model. The equilibrium capacity of DBT adsorption has been calculated at about 39.1 mg/g. This has also been 25.8 mg/g for TBM (tertiary butyl mercaptan). The adsorption capacity has increased by adding to the adsorbent dosage. Thermodynamic studies expose the negative values for ΔS0 (-8.99 kJ/mol. K), ΔH0 (-21.05 kJ/mol), and ΔG0 (8.91 kJ/mol), which demonstrate that DBT adsorption has been a natural exothermic process. In addition, this experiment verifies that the substitution of N into the carbon structure improves the DBT removal efficiency in comparison with pristine CNT as an adsorbent. The removal efficiency of DBT onto GCN has been approximately 80%, i.e. 20% higher than that of pure CNT. Results show that the adsorption capacity of DBT as a cyclic source of mercaptan has been higher than Tertiary butyl mercaptan (TBM) as a liner one. The DBT adsorption mechanism is done by π–π electron interactions between the aromatic structures of DBT, lone-pair electrons of the S atoms, and the pyridinic GCN planes band.

Iron removal from aqueous solution via ultrasound-assisted adsorption using Typha australis leaves as low cost adsorbent had been studied. The effects of various experimental parameters like mass of the Typha australis adsorbent and contact time have been investigated using a batch experiment. The adsorption kinetic data were analyzed using the Pseudo First Order (PFO) and Pseudo Second Order (PSO) models. The adsorption modeling was carried out using the Langmuir, Freundlich and Redlich-Peterson adsorption models. For kinetic study, the adsorption process fitted the PSO model and agreed with chemisorption. Both the Langmuir and Redlich–Peterson models were found to fit the adsorption isotherm data well, but the Redlich– Peterson model was better. The maximum adsorption capacity from the Langmuir model (qmax) was 0.84 mg/g. The results of the present work showed that the Typha australis leaf, without any treatment has a good potential for iron removal from aqueous solutions via ultrasound-assisted adsorption.