The stump lifting trials were implemented in 5 forest compartments of the JSC ‘’Latvia state forest’’ Vidusdaugava, Rietumvidzeme, Zemgale and Ziemeļkurzeme forestries in autumn, 2012. Total extracted area was 3.5 ha, excluding control. Two stump extraction buckets were compared in these trials – CBI (made in Canada) and MCR-500 (made in Latvia). The scope of the study was to estimate if the prototype of the MCR-500 can compete with stump lifting buckets having positive feedback from industry. Considering that the CBI head cannot prepare soil, this operation was not done by the MCR-500 either. In total 1796 stumps were marked and their main parameters were taken in all trial areas. Extracted biomass was estimated theoretically using biomass expansion factors elaborated in Nordic countries. Allegro CX field computers with SDI software were used in time studies to obtain information about productivity and distribution of productive time in a work cycle. The study demonstrated that productivity of stump extraction with both stump lifting buckets did not differ significantly in 6 cases out of total 10 comparisons.

The study aims to find productivity of biofuel production in pre-commercial thinning, depending on the structure of assortments and to identify factors that influence the cost of mechanized tending of young stands. Five work methods were compared in the study, starting from standard thinning (production of sawn timber, pulpwood and firewood) with no use of accumulating device and finalizing with the biofuel method – no other assortments except biofuel are produced and the most intense use of accumulating device is considered. Accumulating device is not used for production of standard round-wood assortments. The experiments were implemented in February – March, 2013. The material produced in the study was used by ‘Graanul Pellets’ company to evaluate possibilities to use timber extracted in pre-commercial thinning of coniferous stands in production of premium class pellets. The average productivity in different stands is statistically different. The study shows that productivity of harvesting is 3.7 … 5.1 m**3 hE-1, which can be increased by more intensive use of accumulation. No difference found between work methods in forwarding trials, but productivity grows with increase of share of firewood. Average loading time 26 min, unloading 3.6 min, average load 6.0 m**3 . Prime-cost calculation shows that harvesting costs depending on the working method is in the range of 22.4 … 26.5 EUR mE-3. Comparison of potential expenses and incomes demonstrates that economically the most efficient is production of traditional assortments (sawn wood, small size sawn wood, pulp wood and firewood) with an active use of accumulating function.

The study represents results of productivity studies of mechanized ditch cleaning using Ponsse Fox harvester adapted to multi-tree handling H6 head in forest drainage systems managed by Joint stock company “Latvia state forests”. The aim of the study is to evaluate productivity of extraction of biomass from ditches depending on working method and to estimate factors affecting prime-cost of biofuel in mechanized harvesting. The study results demonstrate that the 2nd method (mechanized extraction of roundwood and following motor-manual cleaning of remaining vegetation) is the most efficient solution for mechanized cleaning of ditches. Benefits of the 2nd method are smaller costs of undergrowth removal and bigger output of solid biofuel. Ponsse Fox harvester demonstrated sufficient work quality and productivity in the trials; however, it would be wise to use heavier harvesters or caterpillar excavator based harvesters in ditch cleaning. Using the 2nd method, a harvester can extract about 227 ha of ditches (23,000 m3 ) annually.

In the 30ies of the 20th century stump extraction was identified as one of the most prospective technologies of forest sector to secure deliveries of solid biofuel. Now we are returning to the same challenges having the same targets – to secure energy independence and competitiveness of forest sector. MCR 500 is the prototype of combined stump extraction and mounding bucket for caterpillar excavator produced in Latvia by the LSFRI Silava and engineering company Orvi SIA. The device is made for extraction of stumps with diameter up to 50 cm. Additional benefit of the device is its ability to prepare soil for the forest regeneration by making mounds. The article summarizes results of productivity trials of stump extraction using the MCR 500 head and following forwarding of the material. Data from earlier studies are used to characterize comminution and road transport of stumps and chips. In total 3.5 ha were extracted during the studies. A harvested amount of stumps was estimated using biomass equations. It will be updated in further comminution studies. Average stock of extractable biomass (stumps and coarse roots) on the experimental sites was 28 tons ha-1. Productivity of stump extraction was 2.4...3.4 tons per efficient hour. Consumption of efficient time for scarification of soil was 3.4...4.3 hours per ha. Forwarding took 30 min per load (2.6 tons per efficient working hour). Prime cost of chips according to biomass equations is 9.78 Ls LV mE-3, according to expert judgement based harvested stock is 6.38 Ls LV mE-3.

The aim of the study is to ascertain how different compositions of stand species affect the work of the harvester in commercial thinning under Latvia’s conditions. The data of the harvester – time-tracking files (*.drf) have been used as a basis for the study, where productivity is expressed as the prepared amount of round timber in cubic meters in a unit of time – an hour (m**3 hE-1). The data were collected from 100 commercial thinning areas which were divided into three types depending on the composition of the species: pure pine stands, pure spruce stands and deciduous tree mixed stands (mixed with coniferous trees). All the data for the study were collected in the forests managed by JSC ‘Latvia`s State Forests’. By summarizing the data, it has been established that in pure pine stands the average volume of the stem to be removed is 0.092 m**3, in mixed stands – 0.085 m**3 and in pure spruce stands - 0.068 m**3. The research demonstrates that the harvester showed its highest productivity while working in pure pine stands – 3.96 m**3 hE-1, the second best result was achieved in the mixed stands – 3.67 m**3 hE-1, but the lowest rate was demonstrated in pure spruce stands – 3.09 m**3 hE-1. Significant differences were observed in the productivity of the harvester between pure pine and pure spruce stands. Comparing the calculations of standard deviations in the harvester productivity, it can be seen that they are the biggest in mixed stands, while the lowest rate is demonstrated in pure spruce stands.

Machining of wood of soft deciduous trees is currently based on the knowledge about cutting of wood of hard deciduous and coniferous trees and has not developed a comprehensive research methodology of cutting processes. Therefore, the objective of the study is a development of methodology for longitudinal sawing with circular saw and straight milling that would be utilized with a purpose of acquiring further knowledge on wood cutting and the improvement of cutting tool designs. Sub-objective of the study is determination of duration of cutter’s wear periods when using developed methodology. For the purpose of solving problems regarding cutting process of soft deciduous wood, the optimization of cutting tools and cutting modes were carried out in conditions that comply with the tendencies of the practise. The cutting process was carried out by a computer numerical control machine and the data acquisition by electronic measuring instruments. Aspen (Populus tremula L.) wood was used for wood samples. The methodology was developed for sawing, which complements the authors previously described methodology of the milling process investigations. Initially, only the results of periods of cutter wear and cutting velocity effects on these periods when milling process is used were obtained. It was concluded that the methodology can be used for further investigations and the critical wear period begins two times later when cutting velocity increases twice.

The aim of this study is to improve the practice of mechanical forest site preparation (FSP) by identifying typical characteristics of FSP, including the direction of FSP machinery, manoeuvre count depending on configuration of parcel and forest type and width of manoeuvre track; to evaluate the productivity depending on different forest growing conditions; to create schemes of technological corridors for commercial thinning; to improve scheme of FSP according to the scheme of technical corridors for commercial thinning and to evaluate changes in the count of manoeuvres and total distance travelled. In this study, we have developed methods to evaluate the quality of FSP. Methods used in this study include GIS analysis of vector data from FSP machinery tracking devices and LiDAR (Light detecting and ranging) data analysis for terrain information. Study shows that there is a significant difference in productivity when the machinery of FSP is driving in different angles to the longitudinal axis of parcel. Reduced productivity is justified by prioritizing topography of the forest floor. Slope is a decisive factor in the ground water movement and should be considered in FSP planning. Study shows that the developed method could be implemented in practice of forest management in 41% of sampled forest stands.

Tracked forwarders is one of the solutions for the forest soils with poor bearing capacity providing ability to use well-known technology for reasonable cost to improve accessibility of forest resources. Tracked forwarders are not common in forest nowadays and only a few models are produced serially. The ProSilva F2/2 is a new middle-class forwarder, whose frontal tracks are replaced with big tires, ensuring large contact surface, increased mobility of the machine and significantly reduced mass without loosing the load capacity (15 tonnes). The aim of the study was to evaluate productivity, soil impact and cost of the roundwood forwarding using the ProSilva F2/2. The study was conducted in Finland. Productivity (time per crane cycle, split into operations and loads), load size, depth of ruts and soil compaction were estimated during the study. According to the study results, the average productivity is 16 m**3 per hour (driving distance to a landing site 200 m, driving speed 2.8 km hE-1, average load 9.7 m**3). The productivity can be significantly increased by more efficient utilization of the load capacity and by using gripper with the tilt function. The length of ruts on peat soil (56 m haE-1) does not exceed the permitted threshold values in Latvia. The compaction of soil took place mainly in topsoil, no changes in soil density were observed in deeper soil layers. The prime cost of forwarding according to the preliminary estimates is 2.5 € mE-3 if the annual production is at least 62000 m**3. Utilization rate is important to keep forwarding cost low.

The aim of the study was to determine the impact of the harvester cutting head feed roller type on the mechanical damages of processed roundwood timber in post manufacturing. The study presents the comparison of the gentle Moipu plate wheel rollers and conventional feed rollers having bigger spikes (hereinafter named - conventional feed rollers). The total amount of segments processed with the gentle Moipu plate wheel rollers was 2199, whereas the amount of segments processed using the conventional feed rollers was 5308. When processing roundwood with the gentle feed rollers, in the 1st flow 8.2% of timber was rejected as substandard due to defects. The corresponding figure in the 2nd flow was 5.2% of the material in which the damage in the form studs was caused by the feed rollers. When processing the timber with conventional feed rollers, the percentage of the damage – dents caused by these rollers in the 1st flow was 26.7%, in the 2nd flow – 43.7% and in the 3rd flow only 2.7%. Using the method of characteristics proportion comparison, significant differences have been observed between feed rollers (t = 17.8 is greater than t sub(0.05;∞) = 1.96).

The aim of the study was to compare the productivity and logging costs using the small class harvester Vimek 404 T5 in thinning of birch plantations and young coniferous stands. It was found in the study that due to a lower fuel consumption, maintenance costs and initial investment, the cost of a working hour of the harvester Vimek 404 T5 is significantly smaller than the cost of a working hour of the middle class harvester. The study confirmed that Vimek 404 T5 is a suitable harvester for thinning in a birch plantation; the study also confirmed the previous conclusions about the main advantages of Vimek harvester compared to a middle class harvester in the first thinning – low fuel consumption and costs of maintenance, high productivity and equipment compactness, which allow to reduce the strip road area. The average productivity for Vimek 404 T5 in birch plantation was 6.2 m**3 per productive hour, but in young conifer stand the productivity was 4.9 m**3 per productive hour. The average stem volume in the birch plantation was 0.06 m**3, but in conifer stand 0.05 m**3. Productivity for the same dimension trees in the birch plantation is not significantly different from the data obtained in the thinning of the coniferous stands.