To better understand the real-world emissions of rural vehicles (RVs) in China, 8 China II RVs and 18 China III RVs were tested on a provincial road, rural road and farm road using a portable emissions measurement system. The results are illustrated in contour maps of the speed, acceleration and emission rates and show that CO, HC, NOx and PM emissions differ for the three road types; however, the peak emission points all occur on the provincial road. The average CO, HC, NOx and PM emission factors based on distance for the China II RVs are 9.21, 4.05, 1.68 and 2.58 times higher, respectively, than those of the China III RVs. However, the average NOx emission factors of the China II and III RVs are 2.21 and 1.65 times higher than the corresponding recommended values of national emission inventory guideline, resulting in underestimation of overall RVs’ emissions. Distance-based emission factors of four pollutants ranked from high to low are farm road > rural road > provincial road. In contrast to the average emission factors of the China II RVs on the three road types, those of the China III RVs are significantly less in terms of distance and fuel consumption. The results of other researchers differ from those in this study: the CO emission factor of the China II RVs is 2.12 times higher than that of the China II light-duty diesel vehicles (LDDVs). The PM emission factor of the China III RVs is 2.67 times higher than that of the China III LDDVs. The NOx emission factors of the China II and III RVs are similar to those of the corresponding China II and III LDDVs. Our research increases the understanding of real-world emissions of RVs and can act as great references for policy makers developing RV emission baselines.

Global increase in demand for food supply has resulted in surplus generation of wastes. What was once considered wastes, has now become a resource. Studies were carried out on the conversion of biowastes into wealth using methods such as extraction, incineration and microbial intervention. Agro-industry biowastes are promising sources of carbon for microbial fermentation to be transformed into value-added products. In the era of circular economy, the goal is to establish an economic system which aims to eliminate waste and ensure continual use of resources in a close-loop cycle. Biowaste collection is technically and economically practicable, hence it serves as a renewable carbon feedstock. Biowastes are commonly biotransformed into value-added materials such as bioethanol, bioplastics, biofuels, biohydrogen, biobutanol and biogas. This review reveals the recent developments on microbial transformation of biowastes into biotechnologically important products. This approach addresses measures taken globally to valorize waste to achieve low carbon economy. The sustainable use of these renewable resources is a positive approach towards waste management and promoting circular economy.

Exposure of females to fine particulate matter ≤2.5 μm in diameter (PM2.5) prior to pregnancy could produce adverse impact on fertility and enhances susceptibility of the offspring to a variety of diseases. In the current study, female C57BL/6 mice (6 weeks of age) were exposed to either concentrated PM2.5 or filtered air (average PM2.5 concentration: 115.60 ± 7.77 vs. 14.07 ± 0.38 μg/m⁻³) using a whole-body exposure device for 12 weeks. Briefly, PM2.5 exposure decreased anti-Müllerian hormone level (613.40 ± 17.36 vs 759.30 ± 21.90 pg mL⁻¹, P＜0.01) and increased reactive oxygen species (ROS) level (45.39 ± 0.82 vs 24.20 ± 0.85 arbitrary unit in fluorescence assay, P＜0.01) in oocytes. The exposure increased oocyte degeneration rate (21.5% vs 5.1%, respectively (P＜0.01) and decreased the 2-cell formation rate (71.9% vs 86.0%, P < 0.01). Transcriptome profiling using RNA sequencing showed wide spectrum of abnormal expression of genes, particularly those involved in regulating the mitochondrial respiratory complex in oocytes and metabolic processes in blastocysts. The exposure decreased litter size (6 ± 0.37 vs 7 ± 0.26, P＜0.05) and weight (1.18 ± 0.02 vs 1.27 ± 0.02 g, P＜0.01). In summary, PM2.5 exposure decreased female fertility, possibly through increased ROS production in oocytes and metabolic disturbances in developing embryos. The cause-effect relationship, however, requires further investigation.

Bacillus coagulans is regarded as a clean, safe and helpful probiotic additive in the production of livestock and poultry breeds. Some studies have also shown that Bacillus coagulans can adsorb heavy metals in water, even in the gut of animals. However, whether Bacillus coagulans feeding influences antibiotic resistance gene (ARG) abundance in the gut of lead-exposed laying hens is unknown. To better apply such probiotics in the breeding industry, the present study employed Bacillus coagulans R11 and laying hens in model experiments to test ARG changes in the cecum of laying hens under lead exposure and B. coagulans R11 feeding. The results showed that there was the trend for ARG abundance decreasing in feeding B. coagulans R11 without lead exposure to laying hens in the cecum; however, feeding B. coagulans R11 to laying hens exposed to lead obviously increased the abundances of aminoglycoside and chloramphenicol ARGs. Further experiment found that hydroquinone, dodecanedioic acid, gibberellin A14, alpha-solanine, jasmonic acid and chitin were involved in the abundances of ARGs in the cecum, in addition the abundances of these compounds were also significantly enhanced by lead exposure or combination effects of lead and B. coagulans R11. As a result, the ARG hazards increased with feeding B. coagulans R11 to laying hens exposed to lead, and the key compounds which influenced by the combination effects of lead and B. coagulans R11 might influence the ARGs abundance.

An improved understanding of the historical variation in the emissions and sources (biomass burning, BB vs. fossil fuel, FF combustion) of soot and char, the two components of black carbon (BC), and polycyclic aromatic compounds (PACs) may help in assessing the environmental effects of the Atmospheric Brown Cloud (ABC) in SE Asia. We therefore determined historical variations of the fluxes of soot, char, and PACs (24 polycyclic aromatic hydrocarbons (PAHs), 12 oxygenated PAHs (OPAHs), and 4 azaarenes) in a dated sediment core (covering the past ∼150 years) of Phayao Lake in Thailand. The soot fluxes have been increasing in recent times, but at a far lower rate than previously estimated based on BC emission inventories. This may be associated with a decreasing BB contribution as indicated by the decreasing char fluxes from old to young sediments. The fluxes of high- and low-molecular-weight (HMW and LMW) PAHs, OPAHs, and azaarenes all sharply increased after ∼1980, while the ΣLMW-/ΣHMW-PAHs ratios decreased, further supporting the reduction in BB contribution at the expense of increasing FF combustion emissions. We also suggest that the separate record of char and soot, which has up to now not been done in aerosol studies, is useful to assess the environmental effects of ABC because of the different light-absorbing properties of these two BC components. Our results suggest that besides the establishment of improved FF combustion technology, BB must be further reduced in the SE Asian region in order to weaken the ABC haze.

It is important to evaluate how ambient particles are deposited in the human respiratory system in view of the adverse effects they pose to human health. Traditional methods of investigating human exposure to ambient particles suffer from drawbacks related either to the lack of chemical information from particle number-based measurements or to the poor time resolution of mass-based measurements. To address these issues, in this study, human exposure to ambient particulate matter was investigated using single particle analysis, which provided chemical information with a high time resolution. Based on single particle measurements conducted in the Pearl River Delta, China, nine particle types were identified, and EC (elemental carbon) particles were determined to be the most dominant type of particle. In general, the submicron size mode was dominant in terms of the number concentration for all of the particle types, except for Na-rich and dust particles. On average, around 34% of particles were deposited in the human respiratory system with 13.9%, 7.9%, and 12.6% being distributed in the head, tracheobronchial, and pulmonary regions, respectively. The amount of Na-rich particles deposited was the highest, followed by EC. The overall deposition efficiencies of the Na-rich and dust particles were higher than those of the other particle types due to their higher efficiencies in the head region, which could be caused by the greater sedimentation and impaction rates of larger particles. In the head region, the Na-rich particles made the largest contribution (30.5%) due to their high deposition efficiency, whereas in the tracheobronchial and pulmonary regions, EC made the largest contribution due to its high concentration. In summary, the findings of this initial trial demonstrate the applicability of single particle analysis to the assessment of human exposure to ambient particles and its potential to support traditional methods of analysis.

Air and water quality at a concentrated animal feeding operation (CAFO) in Eastern North Carolina that uses a covered lagoon and anaerobic digester was evaluated for 2 weeks in August 2020. Real-time PM₂.₅ mass concentrations were determined using a reference ADR-1500 nephelometer and high-frequency measurements of dissolved inorganic nitrogen (DIN) were evaluated using autonomously logging sensors. Air and water quality parameters were assessed before, during and after wastewater from the lagoon was irrigated onto adjacent spray fields. Reference measurements were conducted alongside a HOBO weather station to collect real-time wind speed and direction, temperature, and humidity measurements. PM₂.₅ concentrations varied between 0 and 159 μg/m³ with an average concentration of 11 μg/m³, below EPA standard for secondary aerosols of 15 μg/m³. Higher PM₂.₅ concentrations were observed when wind originated from swine barns but not from covered lagoons. Water quality data showed that DIN concentrations downgradient from the CAFO were elevated relative to upstream concentrations. A groundwater seep that drains a spray field contained the highest average DIN concentration (31.0 ± 12.8 mg L⁻¹), which was 25 times greater than upstream DIN concentrations (1.2 ± 0.8 mg L⁻¹). Average DIN concentration at the downstream station was lower than the seep concentration (8.6 ± 16.2 mg L⁻¹), but approximately 8 times greater than upstream. Air quality data show that the lagoon cover was effective at mitigating air quality degradation, whereas DIN concentrations in water were similar to previous studies on CAFOs using open lagoons. In addition, air and water quality parameters were significantly (p < 0.001) higher after irrigation, indicating possible influence due to ammonia and nitrate elevation. Additional research is needed to compare high-frequency data collected from swine CAFOs using capped and uncapped lagoon systems to better understand spatiotemporal air and water quality trends of this practice.

Polycyclic aromatic hydrocarbons (PAHs) in soil can be recalcitrant to solvent extraction after aging. We showed in this study that mixing a small amount of water in the extracting solvent during microwave-assisted extraction (MAE) can release recalcitrant PAHs, resulting in significant improvement in the analyzed concentrations. The improvement factor (F) for the total of 16 priority PAHs (∑PAH16) listed by the United States Environmental Protection Agency was 1.44–1.55 for field soils. By comparing the F values for different soil organic components, we demonstrated that the recalcitrant PAHs were primarily associated with biochar, humic acid (HA), and humin (HM), with the F values for ∑PAH16 of 1.94, 6.62, and 4.59, respectively. The results showed that the recalcitrant PAHs comprised a sequestered fraction and a desorption-limited fraction. NMR spectra showed that water worked alone at elevated temperature to promote hydrolysis of biochar and destroy the macromolecular structure, thus causing the release of the otherwise sequestered PAHs during MAE. The substantial reduction in F values for HA and HM after demineralization indicated sequestration of PAHs in organic-mineral complexes, which can be destroyed by hot water treatment. The release of the sequestered fraction was nonselective and independent of compound hydrophobicity. In comparison, the release of the desorption-limited fraction was positively affected by the hydrophobicity of PAHs and was facilitated by the presence of water in the extracting solvent. The results of this study provide important insights into the sequestration and release of recalcitrant PAHs in soil.

There is increasing concern about the environmental behaviors of microplastics (MPs), in particular fine MPs (FMPs), such as their concentrations, sources, size distributions, and fragmentation by weathering in waters. However, there is little information about size distributions of MP polymer types and their relationships to their sources. Here, we analyzed concentrations, compositions, and size distributions of 18 polymer types of MPs of >20 μm by micro-Fourier transform infrared spectroscopy with a novel pretreatment method in surface waters at five sites from the headwaters to the mouth of a Japanese river, and in influent and effluent from a sewage treatment plant (STP). The microplastic concentrations ranged from 300 to 1240 particles/m³ in surface waters. Cluster analysis identified two primary sources of MPs: residential wastewater at the headwater site and non-point sources from urban areas at downstream sites; concentrations of chemical contaminants from STPs were much higher at the downstream sites. The median particle sizes (D₅₀) of MPs increased in urban areas at the downstream sites and were larger than those in influent and effluent. These results imply the release of larger MPs from non-point sources in urban areas. The size distributions of each polymer and all MPs could be fitted significantly to the Weibull distribution function. Values of D₅₀, shape parameters, and scale parameters estimated from the functions were useful indicators for evaluating size distributions in detail. A significant positive correlation of D₅₀ with the tensile strengths of virgin polymers among 13 dominant polymers detected in the surface water suggests that the fragmentation properties of each polymer are influenced by its physical strength. Multidimensional analysis with concentrations, polymeric compositions, and size distributions of MPs, including FMPs, could provide useful information about their sources and their environmental behaviors.

Breast milk is a unique biological sample that reflects the exposure levels of both lactating mothers and infants. The exposure levels of BPA due to breast milk consumption for infants can be estimated easily, but the method to estimate the total daily intake (TDI) of lactating mothers from breast milk has not yet been established. In this study, BPA concentrations were detected in breast milk samples from 149 lactating mothers from Hunan, China. The median concentration of BPA in breast milk was 0.053 μg/L with a range of 0.001–2.535 μg/L, and a temporal decline trend was found for BPA concentrations in breast milk (p < 0.05). The median intake of BPA via breast milk was 26.8 ng/kg bw/day for 0-3-month-old infants and 7.0 ng/kg bw/day for 4-12-month-old infants. Based on the predicted concentrations of BPA in urine and blood via the conversion coefficients from breast milk, the TDIs of lactating mothers were estimated. The TDIs estimated from the simulated urine concentration were 84.0 ± 175.2 ng/kg bw/day for 0-3-month-old infants' mothers and 36.9 ± 80.8 ng/kg bw/day for 4-12-month-old infants' mothers. The dietary daily intakes estimated from the simulated blood concentration were 579.6 ± 370.8 ng/kg bw/day for 0-3-month-old infants' mothers and 280.1 ± 195.2 ng/kg bw/day for 4-12-month-old infants’ mothers. When assuming the dietary daily intakes in Hunan of the fifth total diet study (TDS) as the “true” total dietary intake of our population, the contribution of diet was estimated to be 63.7%, which suggested that non-dietary BPA exposure may be underestimated.