Affiner votre recherche
Résultats 1-10 de 481
Source analysis of the tropospheric NO2 based on MAX-DOAS measurements in northeastern China
2022
Liu, Feng | Xing, Chengzhi | Su, Pinjie | Luo, Yifu | Zhao, Ting | Xue, Jiexiao | Zhang, Guohui | Qin, Sida | Song, Youtao | Bu, Naishun
Ground-based Multi-Axis Differential Optical Absorption Spectroscopy (Max-DOAS) measurements of nitrogen dioxide (NO₂) were continuously obtained from January to November 2019 in northeastern China (NEC). Seasonal variations in the mean NO₂ vertical column densities (VCDs) were apparent, with a maximum of 2.9 × 10¹⁶ molecules cm⁻² in the winter due to enhanced NO₂ emissions from coal-fired winter heating, a longer photochemical lifetime and atmospheric transport. Daily maximum and minimum NO₂ VCDs were observed, independent of the season, at around 11:00 and 13:00 local time, respectively, and the most obvious increases and decreases occurred in the winter and autumn, respectively. The mean diurnal NO₂ VCDs at 11:00 increased to at 08:00 by 1.6, 5.8, and 6.7 × 10¹⁵ molecules cm⁻² in the summer, autumn and winter, respectively, due to increased NO₂ emissions, and then decreased by 2.8, 4.2, and 5.1 × 10¹⁵ molecules cm⁻² at 13:00 in the spring, summer, and autumn, respectively. This was due to strong solar radiation and increased planetary boundary layer height. There was no obvious weekend effect, and the NO₂ VCDs only decreased by about 10% on the weekends. We evaluated the contributions of emissions and transport in the different seasons to the NO₂ VCDs using a generalized additive model, where the contributions of local emissions to the total in the spring, summer, autumn, and winter were 89 ± 12%, 92 ± 11%, 86 ± 12%, and 72 ± 16%, respectively. The contribution of regional transport reached 26% in the winter, and this high contribution value was mainly correlated with the northeast wind, which was due to the transport channel of air pollutants along the Changbai Mountains in NEC. The NO₂/SO₂ ratio was used to identify NO₂ from industrial sources and vehicle exhaust. The contribution of industrial NO₂ VCD sources was >66.3 ± 16% in Shenyang due to the large amount of coal combustion from heavy industrial activity, which emitted large amounts of NO₂. Our results suggest that air quality management in Shenyang should consider reductions in local NO₂ emissions from industrial sources along with regional cooperative control.
Afficher plus [+] Moins [-]Will open waste burning become India's largest air pollution source?
2022
Sharma, Gaurav | Annadate, Saurabh | Sinha, Baerbel
India struggles with frequent exceedances of the ambient air quality standard for particulate matter and benzene. In the past two decades, India has made considerable progress in tackling indoor air pollution, by phasing out kerosene lamps, and pushing biofuel using households towards Liquefied Petroleum Gas (LPG) usage. In this study, we use updated emission inventories and trends in residential fuel consumption, to explore changes in the contribution of different sectors towards India's largest air pollution problem. We find that residential fuel usage is still the largest air pollution source, and that the <10% households using cow dung as cooking fuel contribute ∼50% of the residential PM₂.₅ emissions. However, if current trends persist, residential biofuel usage in India is likely to be phased out by 2035. India's renewable energy policies are likely to reduce emissions in the heat and electricity sector, and manufacturing industries, in the mid-term. PM₂.₅ emissions from open waste burning, on the other hand, hardly changed in the decade from 2010 to 2020. We conclude that without strong policies to promote recycling and upcycling of non-biodegradable waste, and the conversion of biodegradable waste to biogas, open waste burning is likely to become India's largest source of air pollution by 2035. While our study is limited to India, our findings are of relevance for other countries in the global South suffering from similar waste management challenges.
Afficher plus [+] Moins [-]Application of gas chromatographic retention times to determine physicochemical properties of nitrated, oxygenated, and parent polycyclic aromatic hydrocarbons
2022
Vuong, Quang Tran | Son, Ji-Min | Thang, Phan Quang | Ohura, Takeshi | Choi, Sung-Deuk
Nitrated and oxygenated polycyclic aromatic hydrocarbons (NPAHs and OPAHs) are receiving attention because of their high toxicity compared with parent PAHs. However, the experimental data of their physicochemical properties has been limited. This study proposed the gas chromatographic retention time (GC-RT) technique as an effective alternative one to determine octanol-air partition coefficients (KOA) and sub-cooled liquid vapor pressures (PL) for 11 NPAHs, 10 OPAHs, and 19 parent PAHs. The slopes and intercepts of the linear regressions between temperature versus KOA and PL were provided and can be used to estimate KOA and PL for the 40 targeted compounds at any temperature. The internal energies of phase transfer (ΔUOA) and enthalpies of vaporization (ΔHL) for all targeted compounds were also calculated using the GC-RT technique. High-molecular-weight compounds may release or absorb higher heat energy to transform between different phases. NPAHs and OPAHs had a non-ideal solution behavior with activity in octanol (γₒcₜ) in the range of 19–53 and 18–1,078, respectively, which is larger than the unity threshold. A comparison among four groups of PAH derivatives showed that a functional group (nitro-, oxygen-, chloro-, and bromo-) in PAH derivatives increased γₒcₜ for corresponding parent PAHs by tens (mono-group) to hundreds of times (di-group). This study suggests that the GC-RT method is applicable for indirectly measuring the physicochemical properties of various groups of organic compounds.
Afficher plus [+] Moins [-]Long-term trends of atmospheric hot-and-polluted episodes (HPE) and the public health implications in the Pearl River Delta region of China
2022
Nduka, Ifeanyichukwu C. | Huang, Tao | Li, Zhiyuan | Yang, Yuanjian | Yim, Steve H.L.
Air pollution and extreme heat have been responsible for more than a million deaths in China every year, especially in densely urbanized regions. While previous studies intensively evaluated air pollution episodes and extreme heat events, a limited number of studies comprehensively assessed atmospheric hot-and-polluted-episodes (HPE) – an episode with simultaneously high levels of air pollution and temperature – which have potential adverse synergic impacts on human health. This study focused on the Pearl River Delta (PRD) region of China due to its high temperature in summer and poor air quality throughout a year. We employed geostatistical downscaling to model meteorology at a spatial resolution of 1 km, and applied a machine learning algorithm (XGBoost) to estimate a high-resolution (1 km) daily concentration of particulate matter with an aerodynamic diameter ≤2.5 μm (PM₂.₅) and ozone (O₃) for June to October over 20 years (2000–2019). Our results indicate an increasing trend (∼50%) in the frequency of HPE occurrence in the first decade (2000–2010). Conversely, the annual frequency of HPE occurrence reduced (16.7%), but its intensity increased during the second decade (2010–2019). The northern cities in the PRD region had higher levels of PM₂.₅ and O₃ than their southern counterparts. During HPEs, regional daily PM₂.₅ exceeded the World Health Organization (WHO) and Chinese guideline levels by 75% and 25%, respectively, while the O₃ exceeded the WHO O₃ standard by up to 69%. Overall, 567,063 (95% confidence interval (CI): 510,357–623,770) and 52,231 (95%CI: 26,116–78,346) excessive deaths were respectively attributable to exposure to PM₂.₅ and O₃ in the PRD region. Our findings imply the necessity and urgency to formulate co-benefit policies to mitigate the region's air pollution and heat problems.
Afficher plus [+] Moins [-]Fire retardant performance, toxicity and combustion characteristics, and numerical evaluation of core materials for sandwich panels
2022
Wi, Seunghwan | Yang, Sungwoong | Yun, Beom Yeol | Kang, Yujin | Kim, Sumin
According to fire accident statistics, fires in buildings are increasing. The flame-retardant performance of insulation materials is considered an important factor for preventing the spread of fire and ensuring evacuation. This study evaluated the flame-retardant performance and combustion characteristics of four types of organic thermal insulation used as core materials in sandwich panels. The flame-retardant performance evaluation based on total heat release and heat release rate revealed that phenolic foam (PF) satisfied the criteria for non-combustible grade insulation. An analysis of the hazardous gases released while combustion of the four insulation materials indicated that a significant amount of CO was released—an average of 19,000 ppm or higher—in the rigid urethan foam (PIR) and spray-type polyurethane foam (SPU). The fractional effective dose (FED) value was derived from the gas analysis results according to ISO 13344. PIR and SPU had an average FED value of 2.0 or higher and were identified as very dangerous in the case of fire accidents. Moreover, the evacuation time in the case of a fire in a warehouse-type building was comprehensively analyzed considering the material, size, and height for the four types of insulation. PIR was the most vulnerable to fire, and for PF, the danger limit was not reached until the end of the simulation.
Afficher plus [+] Moins [-]Do industrial parks generate intra-heat island effects in cities? New evidence, quantitative methods, and contributing factors from a spatiotemporal analysis of top steel plants in China
2022
Meng, Qingyan | Hu, Die | Zhang, Ying | Chen, Xu | Zhang, Linlin | Wang, Zian
Industrial parks emit large amounts of anthropogenic heat and aggravate the urban heat island effect, which has become a severe environmental problem worldwide. Few studies explored if the warming effect generated by concentrated industrial facilities (i.e., steel plants in this study) produces an intra-heat island effect in urban built-up areas. Sufficient evidence of an industrial heat island (IHI) effect is lacking, and new quantitative methods are urgently needed to address these issues. Therefore, we proposed a new scheme to quantify the warming effect of large, heat-emitting urban objects versus complex surroundings, and the IHI effect was accordingly defined at a finer scale. This study separated the industrial park from other artificial lands and comprehensively estimated the IHI effects' spatiotemporal variation. The IHI intensities were measured based on varied natural and urbanized references, which provided new evidence for the existence of the IHI effect over space and seasons. The land surface temperature (LST) profiles delineated the downward trend in LST variation from inside to surroundings in the IHI cases on both spatial and temporal scales. The time-series analysis revealed that the IHI effects demonstrated more significant disparities regarding the LSTs between the industrial parks and their surrounding backgrounds during warm seasons than in cold seasons. And a more severe IHI effect was observed in spring and summer, and the weakest IHI intensity occurred in winter. Moreover, the IHI intensity is positively associated to the anthropogenic heat, indicating that the industrial activities contribute to the increased LSTs of the industrial park to a great extent. The rationale of the IHI effect can broaden insight for understanding how urban industrial heat sources influence the regional thermal environment, especially at a finer scale.
Afficher plus [+] Moins [-]Alkylation modified pistachio shell-based biochar to promote the adsorption of VOCs in high humidity environment
2022
Cheng, Tangying | Li, Jinjin | Ma, Xiuwei | Zhou, Lei | Wu, Hao | Yang, Linjun
The objective of this work was to evaluate the adsorption capacity of alkylated modified porous biochar prepared by esterification and etherification (PSAC-2) for low concentrate volatile organic compounds (VOCs, toluene and ethyl acetate) in high humidity environment by experiments and theoretical calculations. Results showed that PSAC-2 has a large specific surface area and weak surface polarity, at 80% relative humidity, its capacities for toluene and ethyl acetate adsorption could be maintained at 92% and 87% of the initial capacities (169.9 mg/g and 96.77 mg/g). The adsorption behaviors of toluene, ethyl acetate, and water vapor were studied by adsorption isotherms, and isosteric heat was obtained. The desorption activation energy was obtained by temperature programmed desorption experiment. The outcomes manifested that the PSAC-2 can achieve strong adsorption performance for weakly polar molecules. Through density functional theory (DFT) simulations, owing to the interaction of hydrogen bonds, oxygen-containing groups became a significant factor influencing the adsorption of VOCs in humid environments. These results could provide an important reference for VOCs control in a high humidity environment.
Afficher plus [+] Moins [-]The impacts of existing and hypothetical green infrastructure scenarios on urban heat island formation
2021
Tivārī, Aravinda | Kumar, Prashant | Kalaiarasan, Gopinath | Ottosen, Thor-Bjørn
Urban Heat Island (UHI) is posing a significant challenge due to growing urbanisations across the world. Green infrastructure (GI) is popularly used for mitigating the impact of UHI, but knowledge on their optimal use is yet evolving. The UHI effect for large cities have received substantial attention previously. However, the corresponding effect is mostly unknown for towns, where appreciable parts of the population live, in Europe and elsewhere. Therefore, we analysed the possible impact of three vegetation types on UHI under numerous scenarios: baseline/current GI cover (BGI); hypothetical scenario without GI cover (HGI-No); three alternative hypothetical scenarios considering maximum green roofs (HGR-Max), grasslands (HG-Max) and trees (HT-Max) using a dispersion model ADMS-Temperature and Humidity model (ADMS-TH), taking a UK town (Guildford) as a case study area. Differences in an ambient temperature between three different landforms (central urban area, an urban park, and suburban residential area) were also explored. Under all scenarios, the night-time (0200 h; local time) showed a higher temperature increase, up to 1.315 °C due to the lowest atmospheric temperature. The highest average temperature perturbation (change in ambient temperature) was 0.563 °C under HGI-No scenario, followed by HG-Max (0.400 °C), BGI (0.343 °C), HGR-Max (0.326 °C) and HT-Max (0.277 °C). Furthermore, the central urban area experienced a 0.371 °C and 0.401 °C higher ambient temperature compared with its nearby suburban residential area and urban park, respectively. The results allow to conclude that temperature perturbations in urban environments are highly dependent on the type of GI, anthropogenic heat sources (buildings and vehicles) and the percentage of land covered by GI. Among all other forms of GI, trees were the best-suited GI which can play a viable role in reducing the UHI. Green roofs can act as an additional mitigation measure for the reduction of UHI at city scale if large areas are covered.
Afficher plus [+] Moins [-]HVAC filtration of particles and trace metals: Airborne measurements and the evaluation of quantitative filter forensics
2021
Mahdavi, Alireza | Dingle, Justin | Chan, Arthur W.H. | Siegel, Jeffrey A.
Filters installed in the heating, ventilation, and air-conditioning (HVAC) systems can serve as air-cleaning and sampling devices for indoor particles. The purpose of this article is to evaluate these dual roles. An occupied home with a central HVAC system equipped with a Minimum Efficiency Reporting Value (MERV, from ASHRAE Standard 52.2) 11 filter was monitored for six weeks. Weekly airborne gravimetric and real-time sampling was performed to measure the particle size distribution and the concentration of total suspended particles (TSP), PM₁₀, PM₂.₅, PM₁, and 12 trace metals. The weekly system runtimes were intentionally changed to provide a wide range of weekly filtration volumes. The quantitative filter forensics (QFF) concentrations of particulate matter (PM) and trace metals were calculated using the analysis of the dust collected on the HVAC filter, the filtration volume, and filter in-situ efficiency. The results indicated that filtration was not influential to remove PM and trace metals as the concentrations during the weeks with continuous HVAC operation were not consistently lower than those during the other weeks. This suggests the dominance of other particle and trace metal source and loss mechanisms weakens the influence of filtration in this home. The QFF evaluation results indicated that the concentration of TSP and over half of the tested trace metals (e.g., Pb, Cd, Ni, V, Sb, K, and Sr) could be estimated by QFF within a factor of two when compared to airborne sampling results. PM₁₀, PM₂.₅, and PM₁ concentrations were significantly underestimated by QFF potentially due to the limitations of size distribution analysis by a laser diffraction particle sizer (LDPS) for the detection of <1 μm particles. Overall, while QFF was promising for TSP and some trace metals, improvement in size distribution analysis could extend the application of QFF for airborne sampling.
Afficher plus [+] Moins [-]Conversion and transformation of N species during pyrolysis of wood-based panels: A review
2021
Xu, Deliang | Yang, Liu | Zhao, Ming | Zhang, Jinrui | Syed Shatir A. Syed-Hassan, | Sun, Hongqi | Hu, Xun | Zhang, Hong | Zhang, Shu
Understanding the migration and conversion of nitrogen in wood-based panels (WBPs) during pyrolysis is fundamentally important for potentially transforming the N-containing species into valuable material-based products. This review firstly summarizes the commonly used methods for examining N evolution during the WBPs pyrolysis before probing into the association between the wood and adhesives.The potential effects of wood-adhesive interaction on the pyrolysis process are subsequently analyzed. Furthermore, the controversial statements from literature on the influence of adhesives on wood pyrolysis behavior are discussed, which is followed by the detailed investigation into the distribution and evolution of N-containing species in gas, liquid and char, respectively, during WBPs pyrolysis in recent studies. The differences in N species due to the heating sources (i.e. electrical heating vs microwave heating) are particularly compared. Finally, based on the characteristics of staged pyrolysis, co-pyrolysis and catalytic pyrolysis, the converting pathways for WBPs are proposed with an emphasis on the production of value-added chemicals and carbon materials, simultaneously mitigating NOₓ emission.
Afficher plus [+] Moins [-]