Introduction It has been noticed many times that schools are buildings with high levels of particulate matter concentrations. Several authors documented that concentrations of particulate matter in indoor school microenvironments exceed limits recommended by WHO namely when school buildings are situated near major roads with high traffic densities. In addition, exercise under conditions of high particulate concentrations may increase the adverse health effects, as the total particle deposition increases in proportion to minute ventilation, and the deposition fraction nearly doubles from rest to intense exercise. Site and methods Mass concentrations of size-segregated aerosol were measured simultaneously in an elementary school gym and an adjacent outdoor site in the central part of Prague by two pairs of collocated aerosol monitors--a fast responding photometer DusTrak and a five stage cascade impactor. To encompass seasonal and annual differences, 89 days of measurements were performed during ten campaigns between 2005 and 2009. Results and discussion The average (all campaigns) outdoor concentration of PM₂.₅ (28.3 μg m⁻³) measured by the cascade impactors was higher than the indoor value (22.3 μg m⁻³) and the corresponding average from the nearest fixed site monitor (23.6 μg m⁻³). Indoor and outdoor PM₂.₅ concentrations exceeded the WHO recommended 24-h limit in 42% and 49% of the days measured, respectively. The correlation coefficient (r) between corresponding outdoor and indoor aerosol sizes increased with decreasing aerodynamic diameter of the collected particles (r = 0.32-0.87), suggesting a higher infiltration rate of fine and quasi-ultrafine particles. Principal component analysis revealed five factors explaining more than 82% of the data variability. The first two factors reflected a close association between outdoor and indoor fine and quasi-ultrafine particles confirming the hypothesis of high infiltration rate of particles from outdoors. The third factor indicated that human activity is the main source of indoor emission of coarse particles. The fourth factor involved only outdoor variables showing the resuspension of coarse ambient aerosol on dry and warm days without its seeming effect on the indoor coarse PM levels. Having in mind that high concentrations of both fine and coarse aerosol were frequently observed in the studied space, our results suggest that indoor exercise in polluted urbanized areas may increase the overall exposure and thus represent a potential health risk to young individuals during physical education at schools.

Introduction In this study, olive tree leaves, collected from 50 sampling sites throughout the Province of Aydın, Turkey, were used to estimate level of pollution by measuring Al, As, B, Ba, Ca, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Ni, Pb, Sr, and Zn concentrations and calculating pollution factor (PF) values. Materials and methods After sample preparation, collected leaves were microwave digested, and extracts were analyzed by an inductively coupled plasma-mass spectrometer. Results and discussion The maximum PF values were ≥10 for a number of elements ranging from 11-13 (Al, As, Cr, Fe, Mn, Ni) to >100 for Cu, Li, and Na. Urban-rural and roadside-nonroadside concentration comparisons showed that some of the elements (As, Cu, and Pb) were at significantly higher levels on urban and/or roadside sampling sites. Summary and conclusion Correlations and factor analysis showed that there may be common sources for some elements, which included several soil types and anthropogenic activities. Based on the results of the statistical source apportionment, possible sources were narrowed down with help of the constructed elemental concentration maps. In conclusion, utilization of olive tree leaves for biomonitoring and assessment of environmental pollution was shown to be possible in the Mediterranean region where they are indigenous and cultivated.

PURPOSE: The aim of this work was to investigate the possibility of using several bush and arboreal plant species, usually present as ornamental plants in street and parks, as environmental indicators of pollution. This is a research paper that evaluates the real possibility of using a fast and low-cost procedure to evaluate the pollution degree through data obtained from plant species growing within an urban environment. METHODS: Leaves of six different bush and arboreal species were collected from different parts of Madrid (Spain), ranging from highly polluted considered areas to medium and low contaminated ones. A total of 66 chemical elements, from major to minor and trace, were determined for every leaf sample by inductively coupled plasma-mass spectrometry. Statistical analyses were carried out using mainly box and whisker plots, linear discriminant analysis and cluster analysis. RESULTS: The pollution by different elements of the studied areas of Madrid cannot be considered generally dangerous for human health. The level detected for the contaminants, in general, is similar or lower than other urban cities. Pb and V concentrations in plant samples tend to increase as traffic density increases. The different studied plant species showed a different capability of accumulation of certain elements. Cedrus deodara accumulates specially Ag, Hg, Mo and V; Cupressus sempervirens, Zr; Pinus pinea, As and Sb; Nerium oleander Ni, Pb, Mo and Se; Ligustrum ovalifolium, Sc and V; and Pittosporum tobira, Ag, Cd, Rb and Sc. CONCLUSIONS: The leaves and needles collected from bush and arboreal plants common in this city have demonstrated to be useful to evaluate the level of pollution not only through the chemical analysis but also through the recognition of the visual injury symptoms. The application of multivariate statistical techniques combined with determining of element concentration and correlation analysis has been proved to be an effective tool for reach the objectives of the present work. This allows visualising quickly the damages and leading the sampling through the points of high-level pollution, saving analysis, time and money.

PURPOSE: Bioaugmentation and biostimulation have been widely applied in the remediation of oil contamination. However, ambiguous results have been reported. It is important to reveal the controlling factors on the field for optimal selection of remediation strategy. In this study, an integrated field landfarming technique was carried out to assess the relative effectiveness of five biological approaches on diesel degradation. The limiting factors during the degradation process were discussed. METHOD: A total of five treatments were tested, including conventional landfarming, nutrient enhancement (NE), biosurfactant addition (BS), bioaugmentation (BA), and combination of bioaugmentation and biosurfactant addition (BAS). The consortium consisted of four diesel-degrading bacteria strains. Rhamnolipid was used as the biosurfactant. The diesel concentration, bacterial population, evolution of CO2, and bacterial community in the soil were periodically measured. RESULTS: The best overall degradation efficiency was achieved by BAS treatment (90 ± 2%), followed by BA (86 ± 2%), NE (84 ± 3%), BS (78 ± 3%), and conventional landfarming (68 ± 3%). In the early stage, the total petroleum hydrocarbon was degraded 10 times faster than the degradation rates measured during the period from day 30 to 100. At the later stage, the degradation rates were similar among treatments. In the conventional landfarming, contaminated soil contained bacteria ready for diesel degradation. CONCLUSION: The availability of hydrocarbon was likely the limiting factor in the beginning of the degradation process. At the later stage, the degradation was likely limited by desorption and mass transfer of hydrocarbon in the soil matrix.

INTRODUCTION: In order to identify a potential surrogate of planktonic ciliate communities for marine bioassessments and evaluating biological conservations, the different taxonomic/numerical resolutions and taxa as surrogates were studied in Jiaozhou Bay, northern China during a 1-year cycle (June 2007–May 2008). MATERIALS AND METHODS: Samples were collected biweekly from a depth of 1 m at each of five sites. A range of physicochemical parameters were also measured in order to determine water quality. RESULTS: The genus- and family-level resolutions maintained sufficient information to evaluate the ecological patterns of the ciliate communities in response to environmental status. The non-loricate oligotrichous ciliate assemblages in both abundance and occurrence may be used as a surrogate of planktonic ciliate communities. Heavy data transformations were an optimal strategy for the species level of planktonic ciliates, while mild data transformations were for the higher. The ordination patterns based on species biomass, occurrence, and biomass/abundance ratio matrices were significantly consistent with that of species abundance data. CONCLUSION: The results suggest that the use of simplifications at both taxonomic and numerical resolutions are time-efficient and would allow improving sampling strategies of large spatial/temporal scale monitoring programs and biological conservation researches in the marine ecosystem with a relative paucity of scientists.

Purpose α-Hexachlorocyclohexane (HCH), β-HCH, and lindane (γ-HCH) were listed as persistent organic pollutants by the Stockholm Convention in 2009 and hence must be phased out and their wastes/stockpiles eliminated. At the last operating lindane manufacturing unit, we conducted a preliminary evaluation of HCH contamination levels in soil and water samples collected around the production area and the vicinity of a major dumpsite to inform the design of processes for an appropriate implementation of the Convention. Methods Soil and water samples on and around the production site and a major waste dumpsite were measured for HCH levels. Results All soil samples taken at the lindane production facility and dumpsite and in their vicinity were contaminated with an isomer pattern characteristic of HCH production waste. At the dumpsite surface samples contained up to 450 g kg⁻¹ Σ HCH suggesting that the waste HCH isomers were simply dumped at this location. Ground water in the vicinity and river water was found to be contaminated with 0.2 to 0.4 mg l⁻¹ of HCH waste isomers. The total quantity of deposited HCH wastes from the lindane production unit was estimated at between 36,000 and 54,000 t. Conclusions The contamination levels in ground and river water suggest significant run-off from the dumped HCH wastes and contamination of drinking water resources. The extent of dumping urgently needs to be assessed regarding the risks to human and ecosystem health. A plan for securing the waste isomers needs to be developed and implemented together with a plan for their final elimination. As part of the assessment, any polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/PCDF) generated during HCH recycling operations need to be monitored.

Purpose Climate warming can change the geographic distribution and intensity of the transmission of vector-borne diseases such as malaria. The transmitted parasites usually benefit from increased temperatures as both their reproduction and development are accelerated. Lower Saxony (northwestern Germany) has been a malaria region until the 1950s, and the vector species are still present throughout Germany. This gave reason to investigate whether a new autochthonous transmission could take place if the malaria pathogen was introduced again in Germany. Materials and methods The spatial distribution of potential temperature-driven malaria transmissions was investigated using the basic reproduction rate (R ₀) to model and geostatistically map areas at risk of an outbreak of tertian malaria based on measured (1961-1990, 1991-2007) and predicted (1991-2020, 2021-2050, 2051-2080) monthly mean air temperature data. Results From the computations, maps were derived showing that during the period 1961-1990, the seasonal transmission gate ranges from 0 to 4 months and then expands up to 5 months in the period 1991-2007. For the projection of future trends, the regional climate models REMO and WettReg were used each with two different scenarios (A1B and B1). Both modelling approaches resulted in prolonged seasonal transmission gates in the future, enabling malaria transmissions up to 6 months in the climate reference period 2051-2080 (REMO, scenario A1B). Discussion The presented risk prognosis is based on the R ₀ formula for the estimation of the reproduction of the malaria pathogen Plasmodium vivax. The presented model focuses on mean air temperatures; thus, other driving factors like the distribution of water bodies (breeding habitats) or population density are not integrated. Nevertheless, the modelling presented in this study can help identify areas at risk and initiate prevention. The described findings may also help in the investigation and assessment of related diseases caused by temperature-dependent vectors and pathogens, including those being dangerous for livestock as well, e.g. insect-borne bluetongue disease transmitted by culicoids.

INTRODUCTION: In this study, we provide strategies for detecting and quantifying the structural isomers of polyfluorinated di- and tri-alkyl surfactants (PFAS) by mass spectrometry (MS). We specifically investigate polyfluorinated dialkylated phosphate ester surfactants (x:2/y:2 diPAPS, (F(CF2) x CH2CH2O-P(O)(O)−-OCH2CH2(CF2) y F)) and their thioether analogues (x:2/y:2 S-diPAPS, F(CF2) x CH2CH2SCH2-C[CH2O)2P(O)(O)−]-CH2SCH2CH2(CF2) y F), which are used for industrial applications, such as oil- and water-repellent coatings on paper and board. DiPAPS have been found in human blood and are metabolised to the persistent perfluoroalkyl carboxylic acids (PFCA) in rats. MATERIALS AND METHODS: A microwave popcorn bag extract was analysed by ultrahigh-pressure liquid chromatography coupled to a negative electrospray ionisation-quadrupole time-of-flight MS. RESULTS AND DISCUSSION: The extract contained S-diPAPS, diPAPS and trialkylated (triPAPS) impurities. TriPAPS were also present in industrial and synthetic diPAPS standards, and were verified with an 8:2/8:2/8:2 triPAPS standard. The eight elemental compositions (m/z’s) of diPAPS in the extract represent 19 precursor ion structures, and the six S-diPAPS m/z’s represent at least 13 structures. The diPAPS had [M-H]− precursor ions of m/z 789, 889,…1,489 and the S-diPAPS of m/z 921, 1,021,…1,421, corresponding to fluorinated chains from C6–18. Each m/z appeared as one to three chromatographic peaks of structural isomers, where, e.g. m/z 1,189 was present as 10:2/10:2, 8:2/12:2 and 6:2/14:2 diPAPS. The isomers formed different products ions, thus only half of the m/z 1,189 diPAPS concentration was measured with one precursor ion > product ion transition. CONCLUSION: In general, knowledge about structural isomers of poly-alkylated PFAS is needed for the estimation of types and amounts of perfluorinated degradation products, such as PFCA from diPAPS.

Background and purpose Surfactant-assisted soil washing and photocatalysis are well-known remediation processes of environmental concern. The application of photocatalysis to treat soil washing extracts containing 4-methylphenol, 4-ethylphenol and 4-tert-butylphenol in the presence of nonionic (C₁₂E₈ and C₁₂E₂₃) and anionic (SDS) surfactants and some of their binary mixtures was investigated in this work by studying the pollutants degradation in the presence of TiO₂ dispersions irradiated with simulated solar light. Materials and methods Clean soil samples were spiked with the investigated alkylphenols. Aqueous solutions of the chosen surfactants were placed in contact for some hours with the spiked soil samples in a rotatory mixer. The pollutants recoveries were evaluated via HPLC analysis. Photocatalytic experiments were performed in solarbox on aqueous solutions and on aqueous surfactant solutions containing the pollutants. Results The pollutants removal from the soil was proven effective using the examined surfactant solutions. The photocatalytic treatment of the wastes was faster using Brij 35, but also SDS and C₁₂E₈-SDS mixtures can be applied. After 2-5 h the complete pollutants abatement was obtained, depending on the surfactant chosen and on the amount of TiO₂ employed. On the contrary, the treatment of wastes containing C₁₂E₈ was an extremely slow process. Conclusions The photocatalytic approach can be applied to remove the examined aromatic pollutants from the washing wastes, confirming the viable coupling between this advanced oxidation method and the surfactant-based soil remediation treatments. Surfactant adsorption onto TiO₂ and micelles concentration play a dominant role.

BACKGROUND, AIM AND SCOPE: Seed treatments are widely used on cereals and other annual crops throughout Europe. Most of the formulated pesticide is found on the outside of the seed, the husk. Risk assessments of seed treatments are especially needed for granivorous mice living in the agricultural landscape e.g. for registration using the guidance for risk assessment for birds and mammals (EFSA 2009). The dehusking of seeds before consumption is a known behaviour of these mammals, but so far, no quantitative data on the reduction of exposure of seed treatments by dehusking were published. Therefore, we aimed at providing a first quantitative estimate of this behaviour-related exposure reduction for the wood mouse (Apodemus sylvaticus) with different seed types. MATERIALS AND METHODS: We evaluated the efficiency of dehusking behaviour of 20 wood mice captured in the wild for four different seeds (wheat, barley, maize and sunflower). One experimental setup used a fungicide seed treatment where the remaining seed husks of consumed seeds were analysed with a HPLC-MS/MS technique. In the second setup, we measured generic pigment present in a blank seed treatment formulation and determined the leftover pigment in the husks with a photometric technique. RESULTS: The exposure reduction was similar for the fungicide and the pigment design where the same seed types were studied. We could demonstrate exposure reductions ranging from around 60% for cereals to almost 100% for sunflower seeds as a result of the dehusking behaviour. DISCUSSION: Since exposure reduction was similar in both approaches, working with pigments would be a generic way to estimate the impact of dehusking behaviour on seed treatment exposure. This behaviour can result in a substantial exposure reduction and should, therefore, be considered in a seed-type specific way in the risk assessment of pesticide seed treatments. CONCLUSIONS: It is proposed to include a seed-specific dehusking factor in the calculations of estimated theoretical exposure of seed treatments for granivorous mice. The approach of accounting for a dehusking-related exposure reduction by field relevant wild mammal species seems a more promising way to advance the risk assessment instead of using generic species and neglecting behavioural traits. The pigment approach could be used to gather data for exposure reduction for other species and seed types. Its advantage is that it is harmless to the test species and comparatively cheap since no chemical analysis is involved. RECOMMENDATIONS AND PERSPECTIVES: Seed treatments are used for most of the cereal crops grown in Europe today. Their advantages usually include a lower application rate and the reduction of drift compared to a conventional spraying regime. However, there is a potential risk especially for granivorous mice, and its assessment is challenging in case of a high residue concentration on the dressed seeds. The concept of a dehusking factor in the risk assessment scheme for seed treatments for granivorous mice is a valid approach to account for the behavioural exposure reduction, and generic data could be easily generated also for other wild mammal species and other seed types, possibly analysing the pigment in commercial seed treatment formulations.