Colloidal phosphorus (CP) as an additional route of P mobilization in soil solution has gained much attention. A batch experiment was conducted to investigate the effect of sheep manure-derived biochar (SMB) on CP release from various land uses (paddy, vegetable, tea, and citrus) at a rate of 0% as a control treatment (CK), 1% as a low (L) level, 2% as a middle (M) level, and 4% as a high (H) level of SMB application. The CP and MRPcₒₗₗ in the solution increased from 30.58 to 88.97% and from 2.45 to 55.54% of total P (TP), respectively. The SMB enhanced CP release in all the soils and all the treatments (except CK and L levels in tea soil; CK, L, and M levels in vegetable soil; and L and M levels in citrus soil). Multiple linear regression revealed a significant correlation between CP and MRPcₒₗₗ and between colloidal iron, aluminum, calcium, and total organic carbon (Fecₒₗₗ, Alcₒₗₗ, Cacₒₗₗ, and TOCcₒₗₗ) and pH, which may play an important role as CP carriers that could depend on the pH. This study suggests that the application of SMB in the soil at an appropriate rate of 1 and 2% for tea and vegetable soils, respectively, could be beneficial to avoid the risk of CP release in water bodies.

Spent pot liner (SPL) is a toxic solid waste generated in the aluminum mining and processing industry. SPL is considered as an environmental pollution agent when is dumped on environment. Thus, it is important to access its toxicological risk for the exposed organisms. The comet assay and micronucleus test are efficient tests to detect genotoxic/mutagenic compounds by DNA damage observation. Therefore, in the present study, the genotoxic potential of SPL was evaluated through the micronucleus and comet assay on human leukocytes. After ethics committee approval (COEP—UFLA n°. CAAE 11355312.8.0000.5060), blood aliquots collected from healthy volunteers were exposed to increasing concentrations of SPL (from 0.1 to 80 g L⁻¹). All SPL treatments, including the lowest concentration applied (0.1 g L⁻¹), significantly increased the micronucleus frequency. The frequency of DNA damage was determined by visual scores (from 0 to 4) and the results were expressed on percentage of damage and arbitrary units (AU). CaCl₂ (0.01 M) was applied as negative control (NC) and doxorubicin (10 μg mL⁻¹) as positive control (PC). It was observed a dose-dependency between SPL treatments: as SPL concentration for cell incubation increases, the frequency of damage on DNA also increases. Cells incubated on the NC presented nucleoids class 0 to 2, while those exposed to SPL presents nucleoids class 0 to 4. SPL-incubated cells increasing significantly the frequency of nucleoids class 4. For the PC, the UA of damage was 267.74, which is lower than the one observed for the treatments with high doses of SPL (40–287.40 g L⁻¹ and 80–315.30 g L⁻¹). Thus, it was demonstrated that the SPL is a genotoxic agent that induces DNA damage on exposed organisms.

Urban plants can improve several environmental pollution problems in cities, especially dust prevention, noise reduction, purification of the atmosphere, etc. To explore the influence of dust deposition on the spectral characteristics of the leaf, a foliar dust deposition prediction model based on high-spectrum data was established. Taking Euonymus japonicus L., the common greening tree species in Beijing, as the research object, high (T1), medium (T2), and low (T3) dust pollution gradients were set and hyperspectral data were collected. Results showed that: (1) in the dust-contaminated environment with different concentrations, the trend of the reflectance curve of the leaves of Euonymus japonicus L. was generally consistent. The spectral reflectance of the leaf surface was positively correlated with the amount of leaf dust. (2) There were five obvious reflection peaks and five main absorption valleys with the same positions and ranges in the 350–2500 nm range. (3) The spectral reflectance of leaf flour dust particles of Euonymus japonicus L. was significantly different before and after dusting, and its size was generally clean leaves > dust-depositing leaves. The sensitive range of its spectral response was 695–1400 nm. (4) The overall trend of the first derivative spectrum was basically the same. The red edge slope and the blue edge slope appeared as T3 > T2 > T1, the red edge position and the blue edge position appeared as T1 < T2 < T3. The red edge position of the leaf surface after dust deposition had an obvious "blueshift", and the moving distance increases with the increase of dust retention on leaf surface. (5) The leaf water index (y = − 1.18x² + 0.5424x + 0.9917, R² = 0.8030, RMSE = 0.187) had the highest accuracy in the regression model of leaf surface dust deposition using spectral parameters. The test showed that the R² reached 0.9019, which indicated that the model has a good fitting effect. This prediction model can effectively estimate the dust deposition of the leaf surface of Euonymus japonicus L.

This study investigated the impact of adding zeolite (F), superphosphate (G), and ferrous sulfate (L) in various combinations on reducing greenhouse gas (GHG) emission and improving nitrogen conservation during factory-scale chicken manure composting, aimed to identify the combination that optimizes the performance of the process. Chicken manure was mixed with F, G, FL, or FGL and subjected to windrow composting for 46 days. Results showed that global warming potential (GWP) was reduced by 21.9% (F), 22.8% (FL), 36.1% (G), and 39.3% (FGL). Further, the nitrogen content in the final composting product increased by 27.25%, 9.45%, and 21.86% in G, FL, and FGL amendments, respectively. The fertilizer efficiency of the compost product was assessed by measuring the biomass of plants grown in it, and it was consistent with the nitrogen content. N₂O emission was negligible during composting, and 98% of the released GHGs comprised CO₂ and CH₄. Reduction in GHG emission was mainly achieved by reducing CH₄ emission. The addition of FL, G, and FGL caused a clear shift in the abundance of dominant methanogens; particularly, the abundance of Methanobrevibacter decreased and that of Methanobacterium and Methanocella increased, which was correlated with CH₄ emissions. Meanwhile, the changes in moisture content, NH₄⁺-N content, and pH level also played an important role in the reduction of GHG emission. Based on the effects of nitrogen conservation, fertilizer efficiency improvement, and GHG emission reduction, we conclude that G and FGL are more beneficial than F or FL and suggest these additives for efficient chicken manure composting.

The anoxic and reductive aquatic environment is formed easily in summer due to the global warming, which may accelerate endogenous release. In this experiment, four different dosages of calcium peroxide (CaO₂) were adopted to study the control effects of nutrients release from the sediments in the simulated landscape waters. The results demonstrated that CaO₂ addition could effectively improve the physicochemical properties and microbial composition in sediments, and an obvious improvement was achieved with a larger dosage. It was observed that the surface sediments of experiment groups were oxidized to form a capping barrier between the sediment and overlying water, which might cut off the pollutant diffusion in sediment. Meanwhile, CaO₂ could decrease the nutrients concentration in water obviously, and the reduced effect was positively correlated with the CaO₂ dosage. Compared with the nutrients release fluxes in CK (105.89 mg-TN m⁻² day⁻¹, 106.48 mg-NH₄⁺-N m⁻² day⁻¹, 4.14 mg-TP m⁻² day⁻¹, and 4.30 mg-SRP m⁻² day⁻¹), the CaO₂ dosages of 0.12 and 0.18 kg m⁻² could entirely inhibit the nutrients release from sediment, and partially reduce the original pollutants in the overlying water. However, 0.18 kg m⁻² CaO₂ would cause a higher increase of pH value and NO₂⁻-N concentration, and bring potential risk to the aquatic ecosystem. Therefore, 0.12 kg-CaO₂ m⁻²-sediment was selected as the optimal dosage by considering the control effect, economic cost, and potential risk comprehensively. In general, this study provided a quantitative usage method of CaO₂, which is convenient and effective to prevent or control the nutrients release from sediment caused by anoxic and reductive condition in summer.

Ammoniacal nitrogen is considered as one of the major pollutants of the leachate generated from the landfill site and has the potential to deteriorate the environment as well as health. Considering this, locally available agricultural waste, i.e., sugarcane bagasse ash, was employed as an adsorbent for the removal of ammoniacal nitrogen from landfill leachate. Batch-mode experiments were conducted to see the effect of dose (2–60 g L⁻¹), pH (2–12), and temperature (20–60 °C) on ammoniacal nitrogen adsorption. Application of sugarcane bagasse ash showed 60% removal of ammoniacal nitrogen (50 mg L⁻¹ strength) at an optimum dose of 20 g L⁻¹ and 180 min of contact time with an adsorption capacity of 0.31 mg g⁻¹. The Langmuir adsorption model was found to be best fit at 40 °C with R² = 0.944, depicting a monolayer coverage of ammoniacal nitrogen onto sugarcane bagasse ash. According to the result, solute uptake rate could be well described by the pseudo-second-order model (R² = 0.928), whereas the intraparticle diffusion model and Boyd plot indicated that the overall adsorption rate is governed by the external mass transfer. Thermodynamic studies revealed that adsorption is feasible, spontaneous, and endothermic in nature. Hence, the study shows that sugarcane bagasse ash could turn out to be a cost-effective adsorbent for the removal of ammoniacal nitrogen from leachate

Removal and recovery of phosphorus (P) from sewage are essential for sustainable development of P resource. Based on the water quality determination of sludge dewatering filtrate from a wastewater treatment plant in Beijing, this study investigated the adsorption and regeneration characteristics of P by magnetic anion exchange resin (MAEX). The experiments showed that the P adsorption capacity of MAEX could reach a maximum of 2.74 mg/mL when initial P concentration was 25 mg/L and dosage of MAEX was 8 mL/L. The P adsorption on MAEX resin was suitable for large temperature range (283–323 K). However, the adsorption capacity was reduced in various degrees due to the interference of different anions (Br⁻, SO₄²⁻, Cl⁻, NO₃⁻, HCO₃⁻, CO₃²⁻) and organic compounds (bovine serum albumin, humic acid). Kinetics studies indicated that the P adsorption process followed the pseudo-second-order model. The MAEX resin had a rapid P adsorption rate and the P adsorption capacity at 30 min could reach 97.7–99.3% of qₑ. Increase of temperature was favorable to P adsorption on MAEX, and the adsorption isotherm data fitted to Langmuir model more than Freundlich model. Meanwhile, the thermodynamics parameters were calculated; it was shown that the adsorption process was an endothermic reaction. Desorption and regeneration experiments showed that NaHCO₃ was a suitable regenerant, and the P adsorption capacity could reach 90.51% of the original capacity after 10 times of adsorption-desorption cycles; this indicated that MAEX resin has an excellent regeneration performance and thus has a very good application prospect of P removal and recovery. Fourier transform infrared spectroscopy (FTIR) analysis confirmed that ion exchange, charge attraction, and hydrogen bonding affected the removal of P by the MAEX resin. The vibrating sample magnetometer (VSM) analysis revealed that MAEX resin was a kind of soft magnetic materials with good magnetism.

Employment of biosurfactants and biodegradable chelants could further promote sustainability of soil and groundwater remediation tasks. Biosurfactant (soapnut saponin) and biodegrading chelants (ethylenediamine-N,N′-disuccinic acid (EDDS)) were employed to enhance the phytoextraction by native Taiwanese chenopod (Chenopodium formosanum Koidz.), Napier grass (Pennisetum purpureum) cultivar Taishi No. 4, and soapwort (Saponaria officinalis). Ethylene diamine tetraacetic acid (EDTA) was also employed as the control. Contaminated soils as silty clay loam texture was collected from a defunct rice paddy, containing chromium (Cr), cadium (Cd), and copper (Cu). Addition of both soapnut saponin and EDDS proportionally increased bioaccumulation factors (BCFs) of aboveground biomass for all three plants. Taiwanese chenopod demonstrated the best BCF values among three plants, with BCF increased from 0.76 to 2.6 and 1.3 for Cu under the presence of the highest dosages of EDDS and saponin. Plant aboveground biomass did exhibit negative correlation toward biomass metal concentrations. Presence of saponin did exhibit the least negative slopes among the correlations of all three additives for three plants. Taiwanese chenopod did exhibit the least negative slopes among the correlations of all three additives for three plants. Above observations suggested that saponin may have some protection for plants, especially for Napier grass. Taiwanese chenopod could possess more tolerance toward heavy metals than Napier grass does.

Human health is threatened by significant emissions of heavy metals into the urban environment due to various activities. Various studies describing health risk analyses on soil and dust have been conducted previously. However, there are limited studies that have been carried out regarding the potential health risk assessment of heavy metals in urban road dust of < 63-μm diameter, via incidental ingestion, dermal contact, and inhalation exposure routes by children and adults in developing countries. Therefore, this study evaluated the health risks of heavy metal exposure via ingestion, dermal contact, and inhalation of urban dust particles in Petaling Jaya, Malaysia. Heavy metals such as lead (Pb), chromium (Cr), zinc (Zn), copper (Cu), and manganese (Mn) were measured using dust samples obtained from industrial, high-traffic, commercial, and residential areas by using inductively coupled plasma mass spectrometry (ICP-MS). The principal component and hierarchical cluster analysis showed the dominance of these metal concentrations at sites associated with anthropogenic activities. This was suggestive of industrial, traffic emissions, atmospheric depositions, and wind as the significant contributors towards urban dust contamination in the study sites. Further exploratory analysis underlined Cr, Pb, Cu, and Zn as the most representative metals in the dust samples. In accommodating the uncertainties associated with health risk calculations and simulating the reasonable maximum exposure of these metals, the related health risks were estimated at the 75th and 95th percentiles. Furthermore, assessing the exposure to carcinogenic and non-carcinogenic metals in the dust revealed that ingestion was the primary route of consumption. Children who ingested dust particles in Petaling Jaya could be more vulnerable to carcinogenic and non-carcinogenic risks, but the exposure for both children and adults showed no potential health effects. Therefore, this study serves as an important premise for a review and reformation of the existing environmental quality standards for human health safety.

Sacred groves are small or large patches of forest and are rich in biodiversity, store carbon (C) in biomass and soil, besides providing important ecosystem services. However, the information on tree species diversity, biomass, and C storage in sacred groves of Central India, Madhya Pradesh is elusive and fragmented. In the present study, 41 sacred groves were inventoried for tree species diversity, biomass, and C storage in vegetation and soil. A total of 103 tree species from 81 genera belonging to 37 families were recorded. Shannon’s diversity, Dominance, Fisher’s alpha, and species evenness indices for trees varied: 0.77–2.53, 0.07–0.64, 1.58–20.37, and 0.28–0.90 respectively. Tree density ranged 75–675 no. of stems ha⁻¹ with a mean of 271 no. of stems ha⁻¹, while basal area ranged 6.8–47 m² ha⁻¹ with a mean value of 27 m² ha⁻¹. Tree biomass ranged 34.9–409.8 Mg ha⁻¹ with a mean value of 194.01 Mg ha⁻¹, while, tree C ranged between 17.5 and 204.9 Mg C ha⁻¹ with a mean value of 97.0 Mg C ha⁻¹. The total soil organic carbon stock (0–30 cm) ranged from 22.4 to 112.5 Mg C ha⁻¹ with the mean value of 62 Mg C ha⁻¹. Biomass C and SOC contributed 61% and 39% of the total C stocks, respectively. Tree C stock showed a significant positive relationship with tree basal area (R² = 0.968). A total of five tree species belonging to four families were found to be vulnerable in Central India. The present study reveals that the sacred groves of Central India are species rich, have higher C stocks and sequestration potential in both vegetation and soil, and calls for an immediate attention for conservation and planning for long-term C sequestration.