One of the key factors affecting the formation of high-quality forest is thinning. Latvia's yearly budget of commercial thinning is not met; therefore, there are plenty of forests which are not thinned as planned and this leads to declining quality of forest stands. The timber processing industry needs significant excluded volume of timber, but forest owners are unable to maximize profits in future. Extensive logging of commercial thinning is hindered by economic factors and forestry regulations. Logging business is not satisfied with the productivity indicates and restricting forestry and environmental laws. The world's leading forest engineering firm offers a variety of forest harvester design and structural solutions. The first real use of commercial harvesters in commercial thinning in Latvia's conditions revealed several problems. The most important one is how to increase harvester productivity, while ensuring the quality of residual stands. To increase effectiveness of the logging machines and the proportion of commercial thinning, it is necessary to explore main factors affecting harvester productivity. This work aims to clarify the main pressures hampering harvester productivity and evaluate the quality of remaining trees in commercial thinning in Latvia. The main results are that during night productivity of harvester decreases by 12%, while marking trees to be cut down with fluorescent colour increases productivity of harvester at night by 15%. Productivity of harvester in thinning depends on average volume of harvested trees. These results of the work were obtained through various experiments on twelve different commercial thinning areas in Latvia.

The aim of the study is to ascertain how different compositions of stand species affect the work of the harvester in commercial thinning under Latvia’s conditions. The data of the harvester – time-tracking files (*.drf) have been used as a basis for the study, where productivity is expressed as the prepared amount of round timber in cubic meters in a unit of time – an hour (m**3 hE-1). The data were collected from 100 commercial thinning areas which were divided into three types depending on the composition of the species: pure pine stands, pure spruce stands and deciduous tree mixed stands (mixed with coniferous trees). All the data for the study were collected in the forests managed by JSC ‘Latvia`s State Forests’. By summarizing the data, it has been established that in pure pine stands the average volume of the stem to be removed is 0.092 m**3, in mixed stands – 0.085 m**3 and in pure spruce stands - 0.068 m**3. The research demonstrates that the harvester showed its highest productivity while working in pure pine stands – 3.96 m**3 hE-1, the second best result was achieved in the mixed stands – 3.67 m**3 hE-1, but the lowest rate was demonstrated in pure spruce stands – 3.09 m**3 hE-1. Significant differences were observed in the productivity of the harvester between pure pine and pure spruce stands. Comparing the calculations of standard deviations in the harvester productivity, it can be seen that they are the biggest in mixed stands, while the lowest rate is demonstrated in pure spruce stands.

Tracked forwarders is one of the solutions for the forest soils with poor bearing capacity providing ability to use well-known technology for reasonable cost to improve accessibility of forest resources. Tracked forwarders are not common in forest nowadays and only a few models are produced serially. The ProSilva F2/2 is a new middle-class forwarder, whose frontal tracks are replaced with big tires, ensuring large contact surface, increased mobility of the machine and significantly reduced mass without loosing the load capacity (15 tonnes). The aim of the study was to evaluate productivity, soil impact and cost of the roundwood forwarding using the ProSilva F2/2. The study was conducted in Finland. Productivity (time per crane cycle, split into operations and loads), load size, depth of ruts and soil compaction were estimated during the study. According to the study results, the average productivity is 16 m**3 per hour (driving distance to a landing site 200 m, driving speed 2.8 km hE-1, average load 9.7 m**3). The productivity can be significantly increased by more efficient utilization of the load capacity and by using gripper with the tilt function. The length of ruts on peat soil (56 m haE-1) does not exceed the permitted threshold values in Latvia. The compaction of soil took place mainly in topsoil, no changes in soil density were observed in deeper soil layers. The prime cost of forwarding according to the preliminary estimates is 2.5 € mE-3 if the annual production is at least 62000 m**3. Utilization rate is important to keep forwarding cost low.

The aim of the study was to determine the impact of the harvester cutting head feed roller type on the mechanical damages of processed roundwood timber in post manufacturing. The study presents the comparison of the gentle Moipu plate wheel rollers and conventional feed rollers having bigger spikes (hereinafter named - conventional feed rollers). The total amount of segments processed with the gentle Moipu plate wheel rollers was 2199, whereas the amount of segments processed using the conventional feed rollers was 5308. When processing roundwood with the gentle feed rollers, in the 1st flow 8.2% of timber was rejected as substandard due to defects. The corresponding figure in the 2nd flow was 5.2% of the material in which the damage in the form studs was caused by the feed rollers. When processing the timber with conventional feed rollers, the percentage of the damage – dents caused by these rollers in the 1st flow was 26.7%, in the 2nd flow – 43.7% and in the 3rd flow only 2.7%. Using the method of characteristics proportion comparison, significant differences have been observed between feed rollers (t = 17.8 is greater than t sub(0.05;∞) = 1.96).

The aim of the study was to compare the productivity and logging costs using the small class harvester Vimek 404 T5 in thinning of birch plantations and young coniferous stands. It was found in the study that due to a lower fuel consumption, maintenance costs and initial investment, the cost of a working hour of the harvester Vimek 404 T5 is significantly smaller than the cost of a working hour of the middle class harvester. The study confirmed that Vimek 404 T5 is a suitable harvester for thinning in a birch plantation; the study also confirmed the previous conclusions about the main advantages of Vimek harvester compared to a middle class harvester in the first thinning – low fuel consumption and costs of maintenance, high productivity and equipment compactness, which allow to reduce the strip road area. The average productivity for Vimek 404 T5 in birch plantation was 6.2 m**3 per productive hour, but in young conifer stand the productivity was 4.9 m**3 per productive hour. The average stem volume in the birch plantation was 0.06 m**3, but in conifer stand 0.05 m**3. Productivity for the same dimension trees in the birch plantation is not significantly different from the data obtained in the thinning of the coniferous stands.

The aim of the study is to clarify the compliance of machinery information systems used by Latvian logging service providers with the requirements of the Forest Machine Data and Communications Standard StanForD 2010. For determining the number of logging machines and structure registered in Latvia, data from the State Technical Control Agency of Latvia (VTUA) has been used. This dataset includes 2094 registered machinery units from which 1663 units recorded as harvesters and forwarders are distributed for data processing. Using the national AS Latvian State Forests (LSF) database, where 541 machinery units have been recorded, of which 239 harvesters and 302 forwarders, it is determined what and how many machines already use the standard StanForD 2010, how many machines can implement it and which machines are not suitable for the implementation of StanForD 2010. The study showed that the VTUA register does not fully reflect the true quantity of harvesting machines in Latvia and does not provide information about the use of machines. The LSF data provide reliable information on the possibilities of using StanForD 2010 in harvesters in national forests. From the harvesters working in the country’s forests, 52% of the machines use the StanForD 2010 standard. Work should be continued to clarify the possible use of the standard in the machines working in private forests. Similarly, work should be continued with dealers of harvesting machines to identify models for which it is possible to adjust the StanForD 2010 standard and what the cost of adapting the indicative information systems is.

Precision of the forest inventory still is one of the most important problems in the forestry nowadays. The aim of this research was to estimate the results of the combined forest inventory (CFI), using high spatial resolution aerial images in the planned areas of clear-cuts, comparing the results with the calipering and production files of harvesters. Testing of algorithms showed considerable difference in results between the CFI, forest inventory data and harvester production data. CFI results and production data had a close correlation with R2 =0.83. Comparing CFI calculated growing stock with production data, the average relative error amounted to 10.7%, which means the possibility for integration of these results into the forest inventory system. Comparing to CFI, there is a weak correlation between forest inventory and production data with R2 =0.34. The results indicate that LiDAR CFI technology can be used in the forecasting of the forest management, offering precise information about potential amount and economic value of assortments.

The study aims to find out the efficiency of periodic training of the harvester (cut-to-length) operator, using the automatically saved data of the harvesterʼs information system. It has been established that logging service providers and training institutions do not analyse the operatorʼs work before starting the training; therefore, the training is carried out according to certain, standard programs, without going into the previous performance of each trainee operator. The research uses data automatically saved by Ponsse harvesters during the year, obtained from Ponsse Manager. The study found that by using automatically saved data of the harvester information and performing data grouping with subsequent analysis, it is possible to determine the progress in the execution of specific stem processing operations and to identify operations where the instructor should pay increased attention during training. The research analysed the data of 3 operators, obtained while working with Ponsse harvesters in clear-cutting. In the study, it was found that operator A reduced stem processing time by 3%, labour productivity increased by 15%, and fuel consumption per l m⁻³ decreased by 14% over 3 months. Operator B, after training, saw a 20% reduction in stem processing time, a 13% increase in work productivity, and a 5% increase in fuel consumption l m⁻³ over 3 months. Operator C had a 10% increase in stem processing time, a 1% increase in labour productivity, and a 2% increase in fuel consumption l m³ after training.