Impact of a variety of forestry machine types on soil compaction is evaluated in this study according to the measurement of soil penetration resistance at 0 to 80 cm depth. It is concluded in the study that soils with poor bearing capacity (PBC), comparably small penetration resistance and organic layer thicker than 5 cm are less vulnerable to soil compaction. The use of small-size forwarder Vimek 610 allows to reduce soil compaction to an insignificant level in comparison to the control sites, and most or ruts disappear within a few days in PBC conditions. Whereas John Deere 810E, which belongs to the middle-size class of forwarders, significantly compacts soil through the whole measured depth in similar conditions. Rottne F10B and John Deere 810E forwarders represent the same weight category, and soil compaction due to the use of these machines on soils with moderate bearing capacity (MBC) is similar too; however, on soils with weak (WBC) and good (GBC) conditions results are different, mostly due to a different amount of extracted roundwood in both trials. Tracked forwarder was used only in GBC conditions and the results demonstrated significant compaction only down to 22 cm depth. The trials confirm that the depth of the intensity of impact depends on the weight of the machine and amount of material extracted; however, additional measurement data are necessary to characterize the impact quantitatively in different conditions.

Latvia at the moment does not have precise data about long-term storage of Scots pine. Long-term storage in warm season may lead to significant damages for high priced timber, income reduction for timber sellers and quality loss risk for timber buyers, therefore, roundwood is transported as soon as possible, because of the risk of blue stain, crooks and insect damages. Results of this study on Scots pine were obtained during summer–autumn season of year 2015. Scots pine timber quality changes in long-term storage were analysed in 4 sample stacks – set up in summer (25 July) and stored for 100 days. In every sample plot there was a control pile, a pile with harvester spike damages, a pile with bark damages and a pile with harvester spike and bark damages. There were 32 timber assortments in every pile in order to determine also the emplacement effect in stack. In this study a high correlation was found between pine timber quality changes and meteorological conditions, side surface damages and storage length. By analysing the proportion of blue stain in cross-section and its changes during storage between control assortments and assortments with bark and harvester damages, significant differences were observed, therefore it can be concluded that not only bark damages influence the proportion of blue stain, but also harvester spike rollers. Based on the results of this study, we can predict maximum storage duration during summer–autumn period in Latvia, and it is set from 9 – 16 days.

The study represents results of productivity studies of mechanized ditch cleaning using Ponsse Fox harvester adapted to multi-tree handling H6 head in forest drainage systems managed by Joint stock company “Latvia state forests”. The aim of the study is to evaluate productivity of extraction of biomass from ditches depending on working method and to estimate factors affecting prime-cost of biofuel in mechanized harvesting. The study results demonstrate that the 2nd method (mechanized extraction of roundwood and following motor-manual cleaning of remaining vegetation) is the most efficient solution for mechanized cleaning of ditches. Benefits of the 2nd method are smaller costs of undergrowth removal and bigger output of solid biofuel. Ponsse Fox harvester demonstrated sufficient work quality and productivity in the trials; however, it would be wise to use heavier harvesters or caterpillar excavator based harvesters in ditch cleaning. Using the 2nd method, a harvester can extract about 227 ha of ditches (23,000 m3 ) annually.

In society, discussions occasionally raise whether current level of wood cutting in Latvia is not too high to maintain sustainable forest industry and biodiversity. Cutting volumes for the state owned forests are calculated based on the model whose aim is to even the timber stock of each tree species in a long term period. The wood resource extraction in the private forests takes place according to free market conditions and depending on market prices. Therefore amount of round wood delivered from private forests can shift in a large range. The research had two main tasks. First task was to survey primary wood processing companies in Latvia and gather information about their round wood processing volumes, how their processing volumes divides between softwoods and hardwoods, dimensions of round wood companies demand for production and assortment of produced materials. Second task was to evaluate round wood utilization balance in the territory of Latvia and estimate if current use of timber resources in Latvia corresponds to amounts that are sustainable. Research results showed that consumption of softwood timber in Latvia is close to maximum to perform sustainable forestry, but consumption of hardwoods is possible to increase at least by 20–25%. Survey of primary wood processing companies showed that round wood processing volumes in Latvia vary from 6 to 7 million m3 annually and that large enterprises, which count only for 4% from total number of primary wood processing entities, process two thirds from annual round wood volume in country.

The study aims to find productivity of biofuel production in pre-commercial thinning, depending on the structure of assortments and to identify factors that influence the cost of mechanized tending of young stands. Five work methods were compared in the study, starting from standard thinning (production of sawn timber, pulpwood and firewood) with no use of accumulating device and finalizing with the biofuel method – no other assortments except biofuel are produced and the most intense use of accumulating device is considered. Accumulating device is not used for production of standard round-wood assortments. The experiments were implemented in February – March, 2013. The material produced in the study was used by ‘Graanul Pellets’ company to evaluate possibilities to use timber extracted in pre-commercial thinning of coniferous stands in production of premium class pellets. The average productivity in different stands is statistically different. The study shows that productivity of harvesting is 3.7 … 5.1 m**3 hE-1, which can be increased by more intensive use of accumulation. No difference found between work methods in forwarding trials, but productivity grows with increase of share of firewood. Average loading time 26 min, unloading 3.6 min, average load 6.0 m**3 . Prime-cost calculation shows that harvesting costs depending on the working method is in the range of 22.4 … 26.5 EUR mE-3. Comparison of potential expenses and incomes demonstrates that economically the most efficient is production of traditional assortments (sawn wood, small size sawn wood, pulp wood and firewood) with an active use of accumulating function.

The aim of the study was to compare the productivity and logging costs using the small class harvester Vimek 404 T5 in thinning of birch plantations and young coniferous stands. It was found in the study that due to a lower fuel consumption, maintenance costs and initial investment, the cost of a working hour of the harvester Vimek 404 T5 is significantly smaller than the cost of a working hour of the middle class harvester. The study confirmed that Vimek 404 T5 is a suitable harvester for thinning in a birch plantation; the study also confirmed the previous conclusions about the main advantages of Vimek harvester compared to a middle class harvester in the first thinning – low fuel consumption and costs of maintenance, high productivity and equipment compactness, which allow to reduce the strip road area. The average productivity for Vimek 404 T5 in birch plantation was 6.2 m**3 per productive hour, but in young conifer stand the productivity was 4.9 m**3 per productive hour. The average stem volume in the birch plantation was 0.06 m**3, but in conifer stand 0.05 m**3. Productivity for the same dimension trees in the birch plantation is not significantly different from the data obtained in the thinning of the coniferous stands.

The homogeneous and light wood of birch is suitable for different types of treatment processes and is highly valued for products where visual aspect is important, however, birch assortments are highly susceptible to damages caused by fungi during the storage. Such fungal damages cause discoloration of birch roundwood intended for further woodworking. Sapwood discoloration development and its influencing factors for birch roundwood were analyzed in the summer - autumn period of the year 2016 (August, September and October). Control cut for assessment of sapwood discoloration development was made in four birch roundwood stacks in the districts of Auce and Daugavpils. In order to evaluate the influence of harvesting type, side surface damages, placement in pile, storage duration, diameter, distance from the end plane, daily average temperatures, precipitation amount and relative humidity on development of sapwood discoloration, 616 discs from birch log end planes were prepared. After conducting multiple factor linear regression, it was concluded that a significant development of discoloration and its changes for birch roundwood are promoted by harvesting type, placement in pile, distance from the end plane, daily average temperatures and relative humidity (R2 = 0.450). For birch logs that are prepared by harvester with the daily average air temperature + 6 °C, the first signs of discoloration appear after 17 – 18 days, but on all logs stacked in pile they appear after 68 – 69 days. Whereas, with the daily average temperature of + 18 °C, the first signs of discoloration can occur after only six days, but on all logs stacked in pile they appear after 23 days.

The aim of the study was to determine the impact of the harvester cutting head feed roller type on the mechanical damages of processed roundwood timber in post manufacturing. The study presents the comparison of the gentle Moipu plate wheel rollers and conventional feed rollers having bigger spikes (hereinafter named - conventional feed rollers). The total amount of segments processed with the gentle Moipu plate wheel rollers was 2199, whereas the amount of segments processed using the conventional feed rollers was 5308. When processing roundwood with the gentle feed rollers, in the 1st flow 8.2% of timber was rejected as substandard due to defects. The corresponding figure in the 2nd flow was 5.2% of the material in which the damage in the form studs was caused by the feed rollers. When processing the timber with conventional feed rollers, the percentage of the damage – dents caused by these rollers in the 1st flow was 26.7%, in the 2nd flow – 43.7% and in the 3rd flow only 2.7%. Using the method of characteristics proportion comparison, significant differences have been observed between feed rollers (t = 17.8 is greater than t sub(0.05;∞) = 1.96).

The normal wood colour changes due to the biochemical reactions as well as under the fungal exposure. Some of these fungi during all the exposure time cause only a discoloration (staining fungi); others change not only colour, but also the structure of the wood in its further development (wood destructing fungi). The development of blue stain in sapwood of pine roundwood and its influencing factors were studied in the spring summer period of 2016 (April, May and June) in the districts of Nica, Jelgava and Daugavpils. 650 discs from pine log end planes were prepared in order to evaluate the influence of harvesting type, spreading type of fungi spores, placement in pile, storage duration, diameter, distance from the end plane, daily average temperatures, precipitation amount and relative humidity on blue stain of sapwood and rot development. The most important factors influencing the blue stain development on pine roundwood during the storage are the harvesting type of roundwood, spreading type of fungal spores, placement in pile, storage duration, diameter, and distance from the end plane, daily average temperature and amount of precipitation. By evaluating the daily average temperatures, it was concluded that blue stain of sapwood begins to develop when the average daily temperature reaches +5...+6 °С. But when the average daily temperatures reach +10 °С, depending on the harvesting type (chainsaw or harvester) and spreading type of the fungal spores (via air or bark beetle assistance) the first signs of blue stain may occur from 10 to 42 days of storage.