GOAL, SCOPE AND BACKGROUND: Selenium (Se) is one of the most widely distributed elements of the earth’s crust at low concentrations. The extensive use of Se-containing chemicals due to anthropogenic activities has increased the ecological risk to environmental compartments. Plants, under unfavorable environmental conditions, often increase the formation of reactive oxygen species (ROS), and consequently plant antioxidant enzymatic systems have been proposed to be important in plant stress tolerance. The goal of this study was to find out the metabolic responses of plants to Se, to provide quantitative information whether exogenous Se has a beneficial role in plants, and to investigate the potential of vegetation management of Se for potential phytoremediation. MATERIAL AND METHODS: Pre-rooted plants of weeping willows (Salix babylonica L.) were grown hydroponically in growth chambers and treated with Na₂SeO₄ or Na₂SeO₃ at 24.0 ± 1°C for 168 h. Five different treatment concentrations were used, ranging from 0.44 to 8.72 mg Se/L for the treatments exposed to SeO ₄ ²⁻ and from 0.50 to 10.0 mg Se/L for the treatments exposed to SeO ₃ ²⁻ , respectively. Transpiration rates, soluble protein contents and antioxidative enzyme activities of the plants were monitored to evaluate toxicity from exogenous Se exposure. At the end of the study, total Se in the hydroponic solution was analyzed by hydride generation-atomic fluorescence spectrometry (HG-AFS). RESULTS: Both chemical forms of Se at low concentrations showed growth-promoting effects on plants. A significant decrease of transpiration rates and of soluble protein contents of plants was observed at higher Se concentrations after 168 h of exposure. Measurable change of superoxide dismutases (SOD) activity in leaves was only detected under high Se treatments. Catalase (CAT) activity was significantly affected by the Se application. Slight change of peroxidase (POD) activity was measured in all treatments, whereas significant inhibition of POD activity was detected for the plants exposed to SeO ₃ ²⁻ of 10.0 mg Se/L. Se-induced stress appeared in all treatments, thus resulting in measurable increase of glutathione peroxidase (GSH-Px) activity of the plants. Although both chemical forms of Se were taken up by weeping willows efficiently, their uptake rates were different. DISCUSSION: Of all measured parameters, POD and CAT activities in leaves were noted the most sensitive indicator for the plants exposed to SeO ₄ ²⁻ and SeO ₃ ²⁻ , respectively. Deleterious effects on plant physiological functions due to Se application were not observed over 168 h of exposure. This is largely due to the fact that well-established antioxidant enzymatic systems in plants and higher activities of GSH-Px largely reduced the negative effects on plants; SeO ₃ ²⁻ caused much more severe stress to plants than SeO ₄ ²⁻ at higher Se application rates. The uptake mechanisms between the two chemical species were quite different. CONCLUSIONS: Neither visible toxic symptoms nor metabolic lesions were observed at low concentrations of Se, probably due to the effective established enzymatic systems in weeping willows. All selected parameters for toxicity determination were significantly correlated to Se application, but metabolic responses of plants to SeO ₄ ²⁻ and SeO ₃ ²⁻ were quite different. GSH-Px in leaves was probably the principle enzyme responsible for stress reduction from Se exposure. Due to their different chemical properties, weeping willows showed a faster uptake rate for SeO ₄ ²⁻ than for SeO ₃ ²⁻ . RECOMMENDATIONS: Exogenous Se has a beneficial role in plants and vegetation management of Se is a potential remediation strategy in cleaning up Se-contaminated sites. Further investigation on the biochemical mechanism of Se metabolism will provide insight to the specific interactions between Se and plants on the molecular level. PERSPECTIVES: Weeping willow has a sound potential for phytoremediation of Se-contaminated sediment and groundwater because the tree is not only tolerant to Se but also uptakes chemical species from the environment.

BACKGROUND: Goals and Scope. In response to concerns that have been raised about chemical substances that may alter the function of endocrine systems and result in adverse effects on human health, an OECD initiative was undertaken to develop and validate in vitro and in vivo assays to identify chemicals that may interfere with endocrine systems of vertebrates. Here we report on studies that were conducted to develop and standardize a cell-based screening assay using the H295R cell line to prioritize chemicals that may act on steroidogenic processes in humans and wildlife. These studies are currently ongoing as part of the 'Special Activity on the Testing and Assessment of Endocrine Disruptors' within the OECD Test Guidelines Program to review, develop, standardize, and validate a number of in vitro and in vivo toxicological assays for testing and assessment of chemicals concerning their potential to interact with the endocrine system of vertebrates. -: Study Design. Six laboratories from five countries participated in the pre-validation studies. Each laboratory tested the effects of three model chemicals on the production of testosterone (T) and estradiol (E2) using the H295R Steroidogenesis Assay. Chemicals tested were well described inducers or inhibitors of steroidogenic pathways (forskolin, prochloraz and fadrozole). All experiments were conducted in 24 well plates following standard protocols. Six different doses per compound were analyzed in triplicate per plate. A quality control (QC) plate was run in conjunction with the chemical exposure plate to account for inter-assay variation. Each chemical exposure was conducted two or three times. RESULTS: All laboratories successfully detected increases and/or decreases in hormone production by H295R cells after exposure to the different model compounds and there was good agreement in the pattern of response for all groups. Forskolin increased both T and E2 while fadrozole and prochloraz decreased production of both hormones. All chemicals affected hormone production in a dose-response manner with the exception of fadrozole which caused maximum inhibition of E2 at the two least concentrations tested. Some inter-laboratory differences were noted in the alteration of hormone production measured in chemically exposed cells. However, with the exception of the production of T measured at one laboratory in cells exposed to forskolin, the EC50s calculated were comparable (coefficients of variation 34-49%) for all hormones. DISCUSSION: and Perspectives. The results indicated that the H295R Steroidogenesis Assay protocol was robust, transferable and reproducible across all laboratories. However, in several instances that were primarily related to one laboratory there were unexplained minor uncertainties related to the inter-laboratory hormone production variation. Based on the findings from this Phase 2 pre-validation study, the H295R Steroidogenesis Assay protocol is currently being refined. The next phase of the OECD validation program will test the refined protocol across the same group of laboratories using an extended set of chemicals (~30) that will include positive and negative chemical controls as well as a broad spectrum of different potential inducers and inhibitors of steroidogenic pathways.

Background, Aim and Scope Polycyclic aromatic hydrocarbons (PAH) are important environmental contaminants which may lead to increased levels of neoplastic aberrations or tumours in fish liver. Therefore, monitoring of PAH and their effects are part of several international environmental programmes. The aim of the present field study was to investigate the concentrations of the PAH metabolites in fish bile, to elucidate spatial, seasonal and species differences as well as to discuss different strategies of normalisation with regard to environmental monitoring. Materials and Methods: PAH metabolites were determined in the bile fluid of dab (Limanda limanda) and flounder (Platichthys flesus) caught in the North Sea and Baltic Sea between 1997 and 2004. After enzymatic deconjugation, two metabolites were determined by means of HPLC. The limit of detection and the limit of quantification were calculated. The accuracy of the method was tested with a standard reference material. Results were referred to bile volume as well as to biliverdin. Results: The main metabolite, 1-hydroxypyrene, was determined in concentrations from <0.7 to 838 ng/ml in bile of dab (Limanda limanda) and flounder (Platichthys flesus) caught between 1997 and 2004. The values for 1-hydroxyphenanthrene in fish bile were considerably lower (<0.4 - 87 ng/ml). Significant differences in the 1-hydroxypyrene levels were found between summer and winter surveys as well as between the sampling sites in the data set from 2004 (383 dabs and 62 flounders): Highest levels of PAH contamination were found in dab from the German Bight and in flounder from the Baltic Sea. Discussion: Spatial differences in 1-hydroxypyrene concentrations between North Sea and Baltic Sea were discussed, as well as differences in relation to season, sex and species. Three parameters of normalisation (biliary protein, biliverdin and bile pigments) were discussed. Biliverdin was identified as a suitable parameter for the normalisation of PAH metabolites in field samples. Conclusions: Spatial differences in 1-hydroxypyrene concentrations of dab demonstrate the usefulness of PAH metabolites in fish bile as a monitoring parameter in marine regions. Significant differences in 1-hydroxypyrene concentrations were found between summer and winter sampling campaigns. This may be linked to an annual cycle of 1-hydroxyprene in dab. It is also possible that bile synthesis/release in dab differs between the seasons. There is no indication for a time trend from 1997 to 2004. Recommendations and Perspectives: It is recommended to relate PAH metabolites in fish bile to biliverdin concentrations. Although the concentrations are low in offshore regions and bile volumes are small, the method presented here allows one to measure PAH metabolites on an individual level which is a crucial prerequisite for meaningful monitoring studies.

GOAL, SCOPE AND BACKGROUND: Fragrance preparations or perfumes are used in an increasing variety of applications, as for example washing, cleansing, personal care products, consumer goods or in applications to modify indoor air. However, up to now, little is known to the general or scientific public about their chemical identity and the use pattern of single substances, not even for high production volume chemicals. Some toxicological data are published for a comparatively small number of substances with a focus on sensitisation and dermal effects, while other effects are neglected. Information on ecotoxicity and environmental fate are rare, especially for long-term exposure. Data for a detailed hazard and risk analysis are available in exceptional cases only. According to the current legal situation, fragrance industry is self-regulated, which means that pre-market risk evaluation is not required for most fragrances. Odour and the ability to smell play a major role for wildlife for all taxonomic groups. Reproductive and social behaviour, defence, communication and orientation depend on volatile compounds which can be identical to those used in fragrance preparations. Our interdisciplinary approach leads to the question of whether and, if so, to what extent anthropogenic fragrances may influence life and reproduction of organisms in the environment. MAIN FEATURES: Information from literature on use, exposure and biological effects was combined to analyse the state of knowledge. Following an overview of the amounts of fragrances used in different consumer products and their release into the environment, the roles of odours in nature are shown for a selection of compounds. Existing regulation was analysed to describe the data basis for environmental risk evaluation. Finally, recommendations for further action are derived from these findings. RESULTS: Three main results were elaborated: First, fragrance substances are continuously discharged in large amounts into the environment, especially via the waste water. Second, there are some indications of negative effects on human health or the environment, although the data basis is very thin due to the self regulation of the fragrance industry and the regulatory situation of fragrance substances. Third, many odoriferous substances used by man are identical to those which are signal substances of environmental organisms at very low concentrations, thus giving rise to specific mode of actions in the ecosystem. RECOMMENDATION: For the adequate risk assessments of fragrances, test results on their unspecific as well as their specific effects as signal substances are needed. This would imply prioritisation methods and development of useful test methods for specific endpoints for appropriate risk assessments. Before a comprehensive testing and evaluation of results has been finished, a minimization of exposure should be envisaged. Eco-labelling of products containing acceptable fragrance ingredients could be a first step and provide consumers with the respective information. Transparency concerning the fragrance ingredients used and their biological potency will help to build up confidence between producers and consumers. CONCLUSIONS AND PERSPECTIVES: The interdisciplinary approach, bringing together chemical, biological, toxicological and ecotoxicological data with information provided by manufacturers and with legal and consumer aspects, offers new insights into the field of fragrance substances used in consumer products. The amounts and application fields of fragrance substances increases while fate and effects in the environment are hardly known. The current legal situation is not suited to elucidate the effects of fragrances on human health and the environment sufficiently, especially as it was shown that fragrances may play a considerable role in the ecosystem on the behaviour of organisms. According to the precautionary principle, the lack of knowledge should best be tackled by reducing exposure, especially for compounds such as fragrance substances where no ethical reasons object a substitution by less hazardous chemicals.

BACKGROUND, AIMS AND SCOPE: The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. METHODS: The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. RESULTS: On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. DISCUSSION: Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. CONCLUSIONS: The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. RECOMMENDATIONS AND PERSPECTIVES: High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks.

GOAL, SCOPE AND BACKGROUND: This paper is a part of the research work on ‘Integrated treatment of industrial wastes towards prevention of regional water resources contamination — INTREAT’ the project. It addresses the environmental pollution problems associated with solid and liquid waste/effluents produced by sulfide ore mining and metallurgical activities in the Copper Mining and Smelting Complex Bor (RTB-BOR), Serbia. However, since the minimum solubility for the different metals usually found in the polluted water occurs at different pH values and the hydroxide precipitates are amphoteric in nature, selective removal of mixed metals could be achieved as the multiple stage precipitation. For this reason, acid mine water had to be treated in multiple stages in a continuous precipitation system-cascade line reactor. MATERIALS AND METHODS: All experiments were performed using synthetic metal-bearing effluent with chemical a composition similar to the effluent from open pit, Copper Mining and Smelting Complex Bor (RTB-BOR). That effluent is characterized by low pH (1.78) due to the content of sulfuric acid and heavy metals, such as Cu, Fe, Ni, Mn, Zn with concentrations of 76.680, 26.130, 0.113, 11.490, 1.020 mg/dm³, respectively. The cascade line reactor is equipped with the following components: for feeding of effluents, for injection of the precipitation agent, for pH measurements and control, and for removal of the process gases. The precipitation agent was 1M NaOH. In each of the three reactors, a changing of pH and temperature was observed. In order to verify efficiency of heavy metals removal, chemical analyses of samples taken at different pH was done using AES-ICP. RESULTS: Consumption of NaOH in reactors was 370 cm³, 40 cm³ and 80 cm³, respectively. Total time of the experiment was 4 h including feeding of the first reactor. The time necessary to achieve the defined pH value was 25 min for the first reactor and 13 min for both second and third reactors. Taking into account the complete process in the cascade line reactor, the difference between maximum and minimum temperature was as low as 6°C. The quantity of solid residue in reactors respectively was 0.62 g, 2.05 g and 3.91 g. In the case of copper, minimum achieved concentration was 0.62 mg/dm³ at pH = 10.4. At pH = 4.50 content of iron has rapidly decreased to < 0.1 mg/dm³ and maintained constant at all higher pH values. That means that precipitation has already ended at pH=4.5 and maximum efficiency of iron removal was 99.53%. The concentration of manganese was minimum at pH value of 11.0. Minimum obtained concentration of Zn was 2.18 mg/dm³ at a pH value of 11. If pH value is higher than 11, Zn can be re-dissolved. The maximum efficiency of Ni removal reached 76.30% at a pH value of 10.4. DISCUSSION: Obtained results show that efficiency of copper, iron and manganese removal is very satisfactory (higher than 90%). The obtained efficiency of Zn and Ni removal is lower (72.30% and 76.31%, respectively). The treated effluent met discharge water standard according to The Council Directive 76/464/EEC on pollution caused by certain dangerous substances into the aquatic environment of the Community. Maximum changing of temperature during the whole process was 6°C. CONCLUSION: This technology, which was based on inducing chemical precipitation of heavy metals is viable for selective removal of heavy metals from metal-bearing effluents in three reactor systems in a cascade line. RECOMMENDATIONS AND PERSPECTIVES: The worldwide increasing concern for the environment and guidelines regarding effluent discharge make their treatment necessary for safe discharge in water receivers. In the case where the effluents contain valuable metals, there is also an additional economic interest to recover these metals and to recycle them as secondary raw materials in different production routes.

BACKGROUND, AIM AND SCOPE: Electrocoagulation (EC) may be a potential answer to environmental problems dealing with water reuse and rational waste management. The aim of this research was to assess the feasibility of EC-process for industrial contaminated effluents from copper production, taking into consideration technical and economical factors. EC-technology claims to offer efficient removal rates for most types of wastewater impurities at low power consumption and without adding any precipitating agents. MATERIALS AND METHODS: Real wastewater from Saraka stream with high concentrations of heavy metals was provided by RTB-BOR, a Serbian copper mining and smelting complex. Runs were performed on a 10 1 EC-reactor using aluminum plates as sacrificial electrodes and powered by a 40 A supply unit. Results concerning key factors like pH, conductivity and power consumption were measured in real time. Analysis of dissolved metal concentrations before and after treatment were carried out via ICP-OES and confirmed by an independent test via AAS. RESULTS: Several aspects were taken into account, including current density, conductivity, interfacial resistivity and reactor settings throughout the runs, in order to analyze all possible factors playing a role in neutralization and metal removal in real industrial wastewater. DISCUSSION: Electrode configurations and their effects on energy demand were discussed and exemplified based on fundamentals of colloidal and physical chemistry. CONCLUSIONS: Based on experimental data and since no precipitating agents were applied, the EC-process proved to be not only feasible and environmentally-friendly, but also a cost-effective technology. RECOMMENDATIONS AND PERSPECTIVES: The EC-technology provides strategic guidelines for further research and development of sustainable water management processes. However, additional test series concerning continuous operation must be still performed in order to get this concept ready for future large-scale applications.

BACKGROUND, AIM AND SCOPE: Current scientific studies and evaluations clearly show that an increase of urban dust loads, alone or combined with other pollutants und certain meteorological conditions lead to different significant health effects. Premature death, increased hospital admissions and increased respiratory symptoms and diseases as well as decreased lung function can be observed in combination with high pollutant levels. Sensitive groups like elderly people or children and persons with cardiopulmonary diseases such as asthma are more strongly affected. Because of the direct contact between fine particles and lung tissue more information concerning the surface structure (mapping of toxic elements) is required. Materials and Methods:The NanoSims50 ion microprobe images the element composition at the surface of sub-micrometer air dust particles and documents hot spots of toxic elements as a possible threat for human health.Results:The atmospheric fine dust consists of a complex mixture of organic and inorganic compounds. Heavy metals are fixed on airborn particles in the form of hot spots in a nanometer scale. From a sanitary point of view, the hot spots consisting of toxic elements are particularly relevant as they react directly with the lung tissues. Discussion:To what extent particles can penetrate the various areas of the lungs and be deposited there depends on the one hand on their physical characteristics and on the other on breathing patterns and the anatomy of the lung, which is subject to change as the result of growth, ageing or illness. Once inhaled, some particles can reach the pulmonary alveoli and thus directly expose the lung tissues to toxic elements.Conclusions:Especially the mapping of toxic arsenic or heavy metals like copper on the dust particles shows local hot spots of pollution in the dimension of only 50 nanometers.Recommendations and Perspectives:Imaging of elements in atmospheric particles with NanoSIMS will help to identify the material sources.

Background, Aim and Scope The article is focused on dioxin, furan, PCB and organochlorine pesticide monitoring in the surface waters of the Central European, protected natural reserve Krivoklatsko, under the UNESCO programme Man and Biosphere. Persistent compounds are presently transported via different means throughout the entire world. This contamination varies significantly between sites. This raises the question of what constitutes the naturally occurring background levels of POPs in natural, unpolluted areas, but which are close to industrialised regions. Information of real background POP contamination can be of high value for risk assessment management of those sites evidently polluted and for the defining of de-contamination limits. Preserved areas should not be seen as isolated regions in which the impacts of human activities and natural factors are either unexpected or overlooked. Every ambient region, even those protected by a law or other means, are still closely connected to neighbouring human developed and impacted areas, and are therefore subject to this anthropogenic contamination. These areas adjacent to natural reserves are sources of diverse substances, via entry of air, water, soil and/or biota. After an extended period of industrial activities, organochlorine pollutants, even those emitted in trace concentrations have reached detectable levels. For future research and for the assessment of environmental changes, present levels of contamination would be of high importance. This work publishes data of the contamination with organochlorine pollutants of this natural region, where biodiversity and ecological functions are of the highest order. Materials and Methods: Semipermeable membrane devices (SPMDs) were utilised as the sampling system. SPMDs were deployed in two small creeks and one water reservoir selected in the central part of the Krivoklatsko Natural Reserve, where it could be expected that any possible contamination by POPs would be lowest. The exposed SPMDs were analysed both for chemical contents of POPs and for toxicity properties. The chemical analyses of dibenzo-dioxins, dibenzo-furans, PCBs and OCPs were analysed by GC/MS/MS on GCQ or PolarisQ (Thermoquest). Toxicity bioassays were performed on the alga Desmodesmus subspicatus, bacteria Vibrio fischeri and crustacean Daphnia magna. All toxicity data were expressed as the effective volume Vtox. Vtox is a toxicity parameter, the determination of which is independent of SPMD deployment time and pre-treatment dilution (unlike, for example, the EC50 of the SPMD extract). Results: The following chemical parameters were monitored: 1) tetra, penta, hexa and hepta dibenzo-p-dioxins and furans; 2) all those detectable from tri- through deca-polychloriated biphenyls (PCBs) and 3) a group of organochlorine pesticides: hexachlorobenzene and isomers of hexachlorocyclohexane, DDE, DDD and DDT. The concentrations of dioxins and furans on the assessed sites varied from under detection levels up to 7 pg.l-1; PCBs were detected in a sum concentration up to 2.8 ng.l-1; and organochlorine pesticides up to 346 pg.l-1. The responses of bioassays used were very low, with the values obtained for Vtox being under 0.03 l/d. Discussion: Toxicity testing showed no toxicity responses, demonstrating that the system used is in coherence with the ecological status of the assessed sites. Values of Vtox were under the critical value - showing no toxicity. The PCA of chemical analysis data and toxicity responses resulted in no correlations between these two groups of parameters. This demonstrated that the present level of contamination has had no direct adverse effects on the biota. Conclusions: The concentration values of six EPA-listed, toxic dioxins and sums of tetra-hepta dioxins; nine EPA toxic dibenzofurans and the sums of tetra-hepta bibenzofurans are presented together with all tri-deka PCBs and organochlorine pesticides (alfa-, beta-, gama-, delta-HCH, HCB, opDDE, ppDDE, opDDD, ppDDD, opDDT, ppDDT). These values represent possible current regional natural background values of these substances monitored within the Central European region, with no recorded adverse effects on the freshwater ecosystem (up until the present time). Recommendations and Perspectives: Assessment of dioxins, furans and other organochlorine compounds within natural reserves can be important for the monitoring of human-induced impacts on preserved areas. No systematic monitoring of these substances in areas not directly affected by industry has generally been realised. There is a paucity of data of the presence of any of these substances within natural regions. Further monitoring of contamination of both soil and biota by dioxins and furans in preserve regions is needed and can be used for future monitoring of man-made activities and/or accidents. Semipermeable membrane devices proved to be a very good sampling system for the monitoring of trace concentrations of ambient organochlorine compounds. Toxicity evaluation using the Vtox concept demonstrated that those localities assessed expressed no toxicity.