Birch plywood has proved itself to be one of the most rational ways of wood processing. Growing demand of high performance birch plywood products requires a complex numerical analysis based on Finite Element Method (FEM), instead of using simple analytical assumptions, which prevent optimization of plywood construction (lay-up). In the research samples of birch plywood of several thicknesses, both sanded and non-sanded, with fibre direction of external veneer both in the longitudinal and transverse directions were tested. An extensometer and optical strain gauge were used for strain measurement. The FEM analysis, using commercial software SolidWorks Simulation Premium (SW), versus experimental bending and tension testing according to LVS EN 789 was carried out in this paper. The analysis of results indicates that there is a high correlation between the results of the experiments and the FEM. Particularly for in tension loaded specimens one can be tested up to the maximum ply strength (100 MPa); meanwhile, in bending up to 71MPa – the average stress in load bearing ply at the proportionality limit. Due to software restrictions, shear stresses cannot be evaluated. Future studies are considered to investigate terms for designing plywood with dynamic properties of strength and stiffness to be taken into account.

Green infrastructure (GI) is a strategically planned network of high quality natural and semi-natural areas and provides a range of ecosystem services and protects biodiversity in urban settings. It is very important to increase understanding of the role of GI from a scientific and a socio-economic perspective. The main goal was to understand and assess the ways that tourists use from experiencing urban green infrastructure in the cities they visit. An interview questionnaire survey took place among tourists of the following countries and cities: Latvia (Riga and Jelgava) and Portugal (Lisbon and Faro). The questionnaire includes perception, psychological aspects and preferences, behaviour and activities and general questions as well as biographical information about tourists. The study represents that no significant differences have been found between respondent groups in Latvia and Portugal. The results of the survey show that in future there is a need to improve the linkage between GI and social-cultural activities in cities. Therefore, studies for tourists’ perceptions, preferences and uses of GI will provide the alternative management approaches for urban planning and tourism development in future.

The aim of research was to determine peculiarities of relations between mature layer of the stand with distribution of spruce (Picea abies. Kr.) regeneration according phenology forms and growth specifics. The study examined the success of the resumption of spruce in the Leningrad region under the canopy of the parent stand. In stands with different share of spruce and in various forest-typological conditions, the features of the relationship between the maternal canopy of the stand, the distribution of the natural resumption of spruce by phenological forms and its course of growth were investigated. The account of the undergrowth was carried out by two methods: continuous reading and selective-statistical method. Regardless of the state of viability of spruce undergrowth, the increase in success of regeneration goes from a late vegetation season growth start form to an early one. Under the canopy of the maternal tree stand, young spruce of the early form has the best growth and development indices. In general, under the canopy of spruce stands, the annual height increment in spruce undergrowth, regardless of the phenological structure, the size categories and the state of viability, is greater than under the canopy of pine, pine-spruce and birch-spruce stands. The best characteristics of spruce undergrowth, regardless of phenological forms in vaccinio-myrtillo-pinetum type of forest are described. When analysing the characteristics of spruce undergrowth under the canopy of the stand, taking into account the phenological and altitudinal structure, and the state of viability, it was revealed that at the average age prevailing in the spruce undergrowth of the transitional form, the best parameters of growth have small and medium forms and growth in the early form. Analysing the characteristics of spruce undergrowth under the canopy of the stand, taking into account the phenological and height structure, as well as vitality status, it was revealed that at average age, dominating for the spruce undergrowth of transitional form, the best parameters of small and medium groups of undergrowth has early vegetation season growth start form. The best parameters of the growth have a large group of undergrowth of late vegetation season growth start form.

The influence of coniferous stand composition on the density of pine (Pinus sylvestris) and spruce (Picea abies) wood is considered in this work. Processing of a large quantitative material of wood cores with the use of the ANOVA and rank analysis made it possible to reveal the influence on the macrostructure of wood of the quantitative representation of pine and spruce in the stand. In the pine part of the stand, the correlation of the wood density with the zones of early and late xylem is weak or medium. There is no wood density correlation with the width of the annual ring for stands with different shares of pine. In pine-prevailing stands with a share of pine 80% – 100%, there is a weak but reliably straight relationship between wood density and the size of late wood zone and an inverse relationship with early zone of xylem. For forest stands with a smaller part of pine participation, the relationship between these indicators is medium and reliable. For spruce, we observe a close relationship between the density of xylem and the parameters of its macrostructure in all its variants of participation in mixed coniferous plantations. In most of the studied mixed stands, the density of wood in spruce is not significantly differentiated and more homogeneous.

The article provides the research data on the variation of organic matter in the Jaugila Stream, which flows through drained fields fertilized with organic fertilizers. The aim of the research was to determine the effect of manure application in drainage basin to the changes of organic matter concentration in the Jaugila Stream. Water samples for chemical analysis were taken once a month from the drainage water and the river. The samples from the river were taken upstream and downstream manure fertilized fields and the drainage water – from the outlets of the drainage system, which drains the fertilized area. Water analysis was performed by the Analytical Laboratory of Chemical Analysis of the ASU Water Research Institute. BOD7 was determined by titrimetric method. The research has shown that a greater impact on the increase of BOD7 concentrations in the Jaugila Stream was due to the stream water, saturated with the organic matter, flowing from the upstream areas, rather than the drainage water flowing into this stream from manure fertilized area. The assessment of BOD7 concentrations according to the water quality requirements for surface waters determined that in most cases the water of the Jaugila Stream, both in above and below fertilized areas, was in a very good or good ecological status. The impact of manure fertilized areas on the organic matter concentration in the stream was determined to be minimal, as the statistical analysis of the data has shown that the difference between BOD7 concentrations above and below fertilized areas is negligible.

Establishment of sedimentation ponds is a method to reduce the negative impact of forest management (fellings, drainage) on the quality of nearby rivers, lakes and streams. The aim of the study was to determine the efficiency of sedimentation ponds in forest drainage systems during high precipitation periods. Nine sedimentation ponds with different drainage areas were analysed. The sedimentation ponds are located in the northern part of Latvia on different types of soils and managed by the Joint Stock Company ‘Latvia’s State Forests’. In order to determine efficiency of these ponds the following parameters in water samples were measured: nitrate (NO3 -), ammonium (NH4 +), phosphate ion (PO4 3-), total nitrogen and total suspended solid concentration. The amount of precipitation was taken into account. Results show that there is a correlation between the amount of precipitation and concentrations of total suspended solids and total nitrogen. Ammonium ion concentration was the only parameter that significantly exceeded water quality standards in Latvia. Only one of the objects had high concentration of pollutants, which could be explained with the peaty soil of its drainage area. In further studies data should be collected more frequently, three or four days during one precipitation period.

Road landscapes can be considered important resources for place development. They create impression about the infrastructure of places and transport, which is an important aspect of attracting investment and tourism development. Yet this field of landscape planning and design is hardly studied and needs more attention in Latvia. Institutions at different planning levels and from several fields of expertise are involved in road landscape development. In order to achieve successful cooperation among all the parties involved, it is necessary to reflect the information about road landscape development in the way that it can be easily perceived and understood. Studies in landscape perception prove that people perceive visual information about landscape design and planning better than textual information and regular maps. The purpose of the paper is to introduce with a method of three dimensional (3D) road landscape modelling, developed by authors as a tool for road landscape design aesthetic evaluation, which can be used to demonstrate design variants to wider public and stakeholders. We demonstrate what kind of data are necessary for road landscape modelling, how they are obtained and processed, why certain modelling programs are chosen. The methodology, problems, which occurred during the modelling, and the chosen solutions are described. Results show that chosen methodology is appropriate for large scale projects. The experience gained from the project helps to evaluate the suitability of certain computer programs for road landscape planning and design.

In order to improve competitiveness in today’s business environment, farmers also have to think about the rapid technological development in their enterprises. The most important factor that can positively influence the progress of the agricultural sector is the application of modern, efficient and labour-saving technologies at the various stages of crop growing and processing. Introduction of robotics in the farming processes emerges as one of the options. Current state of technologies allows only a few tasks processed by robots to be technologically and economically viable; the most relevant example is lawn mowing robots. One of the issues that prevent widespread use of robots in agriculture is that there are still no regulations or standards in the robotic sector for the industry to allow each robot manufacturer to follow them, such as mountable equipment communication protocols, dimensions of chassis and body, control systems including sensors and actuators etc. Each robot developer chooses his own approach and interpretation in robot protocols and modules. This article presents a conceptual design of mobile robot “Formica 01” for various agricultural applications. A prototype of the proposed design has been developed and in the article various cases of its usage on strawberry fields have been described.

The aim of the study was to assess the ability of pathogens metabolic repair from injury within 10 days of refrigerated storage of milk after high pressure treatment. Two pathogenic strains – Listeria monocytogenes ATCC 7644 (LM) and Escherichia coli ATCC 25922 (EC) were inoculated in ultrahigh-temperature treated (UHT) milk at concentration of about 107 CFU mLE-1 and treated at 400, 500, 550, and 600 MPa for 15 min with inlet temperatures 20 °C, and then stored at 4 ± 2 °C to evaluate survival and growth of pathogens. By increasing the applied pressure, an increased rate of the pathogens’ inactivation was achieved. After 10 days of storage, milk treated at 400 MPa showed growth over 3.5 log CFU mLE-1 of L. monocytogenes and 1.7 log CFU mLE-1 of E. coli. In 550 MPa and 600 MPa treated milk samples after 8 and 10 days of storage colony formation occurred (3 CFU mLE-1 (550 LM) and 2 CFU mLE-1 (550 EC, 600 LM and 600 EC)). Although high pressure treatment is effective method for reducing of pathogenic bacteria, the metabolic repair from injury of bacterial cells in milk during storage should be considered.

Lactobionic acid is a high value added compound industrially produced through energy intensive chemical synthesis, which uses costly metal catalysts, like gold and platinum. In the next years, biotechnological production of lactobionic acid can be supposed to take the full transition to the manufacturing stage. Productivity of lactobionic acid by microbial production can be affected by various factors – choice of microorganism and its concentration, supply of oxygen, temperature, substrate, cultivation method, pH and aeration rate. The aim was to review research findings for lactobionic acid production as well innovative and efficient technology solutions for self-costs reducing. Whey was recommended as a cheap and suitable substrate for the lactobionic acid production. Whey processing has been advised with Pseudonomas teatrolens in 28 °C and in pH 6 to 7 for yielding the highest productivity. The increasing commercial importance urges the progression of schemes for lactobionic acid biotechnological manufacturing.