Controlled-release fertilizers (CRFs) are an effective approach in providing essential nutrients for plant growth while minimizing the loss of nutrients in water and air, reducing contamination risks. However, commercial CRFs often release nutrients either too quickly or slowly due to the properties of their coating materials (polymer or sulfur). In this work, a novel CRF technology was developed using chitosan (CS) and graphene oxide (GO) nanocomposites as coating materials. CS and GO solutions were applied at varying ratios in preparing different nanocomposites. CS and GO formed homogeneous nanocomposite films through their interactions with each other. Fertilizer beads were successfully encapsulated by the CS-GO films using the simple dipping method. Resulting CRFs showed controlled-release behaviors, with nutrient release lasting for about a week. Although additional investigations are required for further evaluation and optimization, this method presents a promising concept for an alternative fertilizer-coating technology.

Goethite is a stable and widespread mineral in soil, which affects the transportation and immobilization of heavy metals in soil. Here, the three-dimensional flower-like goethite (TDFLG) was synthesized by refluxing precipitation method. The modified three-dimensional flower-like goethite (MTDFLG) was prepared by NaH₂PO₄ with dipping method. The obtained samples were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) analysis, N₂ adsorption–desorption (BET), and X-ray diffraction (XRD). SEM images showed that the modification of phosphate had no major changes on the morphology of the original sample and the morphology of MTDFLG after adsorbed U(VI) had clearly change. For the goethite and modified goethite, the BET-specific surface area was 229.96 and 203.17 m²/g, respectively. Moreover, the effects of adsorption time, sorbent dose, solution pH, and initial uranium concentration on the uranium adsorption behaviors were investigated using the two materials as adsorbent for the treatment of uranium-containing wastewater. The results showed that MTDFLG had better adsorption capacity than TDFLG on uranium. The increase in uranium removal on MTDFLG was due to the formation of ternary surface complexes (≡FePO₄UO₂). TDFLG and MTDFLG followed the pseudo-second-order kinetic model and the Langmuir adsorption isotherm model, which indicated that uranium adsorption on TDFLG or MTDFLG is mainly based on chemisorption, and the maximum adsorption capacity of two adsorbents is 48.24 and 112.36 mg/g, respectively.

In this study, MgAl-LDHs and MgFe-LDHs were synthesized via co-precipitation method and in situ coated on pre-washed zeolites through dipping process in beaker. The obtained modified zeolites and original zeolites were utilized as substrates of constructed rapid infiltration systems (CRIS) to remove hexavalent chromium (Cr(VI)) in wastewater. Micro-morphology features and chemical composition of zeolites before and after modification were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray fluorescence spectrometer (XRF). The SEM, XRD, and XRF results demonstrated the feasibility of LDHs coated on the surface of the original zeolites. Purification experiments in simulated CRIS showed that the Cr(VI) removal rates of zeolites/MgAl-LDHs increased by 110.03% on average every concentration (0.5–16 mg L⁻¹) compared with the original zeolites under 24-h HRT. The adsorption capacity of zeolites/MgAl-LDHs reached 66.98 mg kg⁻¹ at 32 mg L⁻¹ initial Cr(VI) concentration, which is nearly twice that of the original zeolites (33.24 mg kg⁻¹) and 1.5 times higher than that of zeolites/MgFe-LDHs (42.01 mg kg⁻¹). Isothermal adsorption tests showed that the Freundlich isotherm equations gave better fitting to the adsorption process. And zeolites/MgAl-LDHs showed a best fit with pseudo-second-order model which meant that the adsorption of Cr(VI) by zeolites/MgAl-LDHs was dominated by chemisorption. Thermodynamic parameters showed that the process of adsorption for the three substrates was spontaneous and endothermic intrinsically. Zeolites/MgAl-LDHs also displayed nearly 60% desorption rate with low concentration eluent (0.01 mol L⁻¹ NaCl). Therefore, zeolites/MgAl-LDHs were chosen out as an optimal substrate for removing Cr(VI) from wastewater in CRIS. Graphical Abstract

The materials and byproducts of the processes used in the metal finishing industry are released as particle contaminants into the air in the workplace. The present study aimed to determine the concentrations and size distributions of these particles and of elements chromium, nickel, copper, manganese, cobalt, and lead (Cr, Ni, Cu, Mn, Co, and Pb, respectively) in a metal finishing industry and evaluate their potential health risks. Particles that are airborne from the dipping baths in the plant were sampled using a Sioutas cascade impactor at five different size fractions (PM>₂.₅, PM₁.₀–₂.₅, PM₀.₅–₁.₀, PM₀.₂₅–₀.₅, PM<₀.₂₅) and gravimetric analyses were conducted on the sampled filters. The GF-AAS 600 graphite atomic absorption spectrophotometer (PerkinElmer Corporation, Waltham, MA, USA) was used to analyze the elements and the method of USEPA was used to assess the health risk. The ratio of fine particles (PM₂.₅) to total suspended particles (TSPs) was 0.6. We observed that 50% of TSPs were composed of PM₁.₀ and that 68–88% of the metals were found in the fine particle fractions. Pb, Cr, and Mn were significantly positively correlated in the PM₁.₀ fraction, and the highest linear relationship was found between Pb and Cr (r = 0.85, p < 0.01). The total hazard quotient (HQ) for PM₂.₅ was 1.43, which is higher than the acceptable limit of 1.0. The excess lifetime cancer risk (ELCR) for hexavalent chromium (Cr[VI]) in PM₂.₅ was 6.09 × 10⁻⁵ for female workers and 6.54 × 10⁻⁵ for male workers, which are higher than the acceptable limit of 1.0 × 10⁻⁶, while total ELCRs for female and male workers were 6.21 × 10⁻⁵ and 6.21 × 10⁻⁵, respectively. The lifetime cancer risk associated with Cr(VI) in Cr electroplating plants should be taken into consideration as a significant health risk for the workers.

Throughout history, synanthropic Musca domestica had remained a worldwide problem whenever poor sanitation and bad hygienic conditions exists. Houseflies growing resistance to chemical insecticides are a rising environmental problem that necessitates search for alternatives. Mentha cervina, Ocimum basilicum, and Coriandrum sativum were tested for bioactivity on M. domestica adults and larvae. They are culinary Mediterranean plants. In adulticidal bioassay, using both CDC bottles and fumigation techniques, basil was the most effective extract with LC₅₀ 1.074 and 34.996 g/L, respectively. Concerning larvicidal bioassay by fumigation technique, coriander had the highest toxicity index with LC₅₀ 29.521 g/L. In both dipping and feeding technique, basil had the highest toxicity with LC₅₀ 32.643 and 0.749 g/L, respectively. Basil showed the highest toxicity results in four out of the five models tested followed by coriander then mint; this result highlights the potentiality of basil as a green insecticide in management of flies and opens new insight in the industrialization of basil-based fly control products.

We studied the response of gypsy moth (Lymantria dispar (Linnaeus) (Lepidoptera: Lymantriidae)) to the content of manganese in food in the laboratory breeding of caterpillars. The food of the caterpillars {Betula pendula Roth (Fagales: Betulaceae) leaves} was contaminated by dipping in the solution of MnCl₂·4H₂O with manganese concentrations of 0, 0.5, 5 and 10 mg ml⁻¹, by which differentiated manganese contents (307; 632; 4,087 and 8,124 mg kg⁻¹) were reached. Parameters recorded during the rearing were as follows: effect of manganese on food consumption, mortality and length of the development of caterpillars, pupation and hatching of imagoes. At the same time, manganese concentrations were determined in the offered and unconsumed food, excrements, and exuviae of the caterpillars, pupal cases and imagoes by using the AAS method. As compared with the control, high manganese contents in the food of gypsy moth caterpillars affected the process of development particularly by increased mortality of the first instar caterpillars (8 % mortality for caterpillars with no Mn contamination (T0) and 62 % mortality for subjects with the highest contamination by manganese (T3)), by prolonged development of the first–third instar (18.7 days (T0) and 27.8 days (T3)) and by increased food consumption of the first–third instar {0.185 g of leaf dry matter (T0) and 0.483 g of leaf dry matter (T3)}. The main defence strategy of the caterpillars to prevent contamination by the increased manganese content in food is the translocation of manganese into frass and exuviae castoff in the process of ecdysis. In the process of development, the content of manganese was reduced by excretion in imagoes to 0.5 % of the intake level even at its maximum inputs in food.