Fast-growing hybrid aspen clones are recommended for establishment of plantation on abandoned agriculture land in Northern Europe. In this study we assessed the productivity, quality and assortment structure of hybrid aspen clones at final felling. Data were collected during the hybrid aspen clonal experiment conducted in the central part of Latvia. Large variation in the productivity level between different clones was affected by growth and survival. From the compared 5 most and least productive clones, based on the yield m**3 haE-1, the faster growing clones have about 17% better survival rate at age 10. Also, the mean annual increment (MAI) differed notably and significantly (p is less than 0.05, α = 0.05) between hybrid aspen clones at the age of 18 years ranging from 7 to 34 m**3 haE-1 yearE-1. Theoretical assortment structure of hybrid aspen at the age of 18 years was the following: 43 ± 4.86% of small dimension saw logs (SDS logs), 21 ± 4.86% high quality saw logs (HQS logs), 18 ± 4.33% pulpwood, 4 ± 0.77% firewood and 13 ± 0.08% of logging residues (tops). The outcome of HQS logs on average is more than 30% from the 5 best clones and further increase can be predicted with age. Stem volume (H2 = 0.32), height (H2 = 0.47) and quality parameters (stem straightness - H2 = 0.73, branch angle - H2 = 0.60) had a high heritability and large differences between clones, indicating notable possibilities to improve the productivity of plantations via selection of the best-growing genetic material.

Impact of a variety of forestry machine types on soil compaction is evaluated in this study according to the measurement of soil penetration resistance at 0 to 80 cm depth. It is concluded in the study that soils with poor bearing capacity (PBC), comparably small penetration resistance and organic layer thicker than 5 cm are less vulnerable to soil compaction. The use of small-size forwarder Vimek 610 allows to reduce soil compaction to an insignificant level in comparison to the control sites, and most or ruts disappear within a few days in PBC conditions. Whereas John Deere 810E, which belongs to the middle-size class of forwarders, significantly compacts soil through the whole measured depth in similar conditions. Rottne F10B and John Deere 810E forwarders represent the same weight category, and soil compaction due to the use of these machines on soils with moderate bearing capacity (MBC) is similar too; however, on soils with weak (WBC) and good (GBC) conditions results are different, mostly due to a different amount of extracted roundwood in both trials. Tracked forwarder was used only in GBC conditions and the results demonstrated significant compaction only down to 22 cm depth. The trials confirm that the depth of the intensity of impact depends on the weight of the machine and amount of material extracted; however, additional measurement data are necessary to characterize the impact quantitatively in different conditions.

One can reasonably argue that issues related to the increased use of renewable energy resources in the energy production processes in Latvia, are at the forefront and will remain there in the future. This relates to the aspect that Latvia is not rich in non-renewable energy resources (around 70% of total primary energy consumption in Latvia is ensured by import, which can lead to undesired effects in many areas), but at the same time, there are available renewable energy resources in Latvia, with an untapped potential to be recognized. In particular this applies to fuel wood, which is already (year 2012) the most important domestic fuel in Latvia. In this context it is important to emphasize that, according to the particular study results, if unexpected socio-economic developments do not take place, raw wood material resources required for different types of fuel wood production in Latvia should be available in the same amount as it is now if not more. As for increasing the amount of fuel wood use in Latvia, an enormous ‘potential’ can be seen in general use boiler houses, where there are currently no technological limitations to utilize this ‘potential’. General use cogeneration plants can be recognized as an even greater ‘potential’ for greater use of fuel wood in Latvia, but given the circumstances of energy supply in Latvia, the ‘potential’ is currently available on a very limited basis. At the same time it is important to note that both of these ‘potentials’ could be significantly reduced in the next few years.

The study aims to find productivity of biofuel production in pre-commercial thinning, depending on the structure of assortments and to identify factors that influence the cost of mechanized tending of young stands. Five work methods were compared in the study, starting from standard thinning (production of sawn timber, pulpwood and firewood) with no use of accumulating device and finalizing with the biofuel method – no other assortments except biofuel are produced and the most intense use of accumulating device is considered. Accumulating device is not used for production of standard round-wood assortments. The experiments were implemented in February – March, 2013. The material produced in the study was used by ‘Graanul Pellets’ company to evaluate possibilities to use timber extracted in pre-commercial thinning of coniferous stands in production of premium class pellets. The average productivity in different stands is statistically different. The study shows that productivity of harvesting is 3.7 … 5.1 m**3 hE-1, which can be increased by more intensive use of accumulation. No difference found between work methods in forwarding trials, but productivity grows with increase of share of firewood. Average loading time 26 min, unloading 3.6 min, average load 6.0 m**3 . Prime-cost calculation shows that harvesting costs depending on the working method is in the range of 22.4 … 26.5 EUR mE-3. Comparison of potential expenses and incomes demonstrates that economically the most efficient is production of traditional assortments (sawn wood, small size sawn wood, pulp wood and firewood) with an active use of accumulating function.

European beech (Fagus sylvatica L.) timber value is high in southern Europe due to a great demand from Asia. Since the timber market is global, over a long time we can expect gradual increase in demand also in other countries, including Latvia, where climatic conditions becomes increasingly more suitable for this species due to ongoing climatic changes. In order to develop recommendation for the use of beech in our country, the aim of the study was to assess the potential financial gain from Fagus sylvatica stands in Latvia. Assortment structure, defined by topdiameter and length, as well as their prices was set based on the literature survey. Results showed higher income from older (115 years) than form younger (58 years) stands: 9108 EUR haE-1, and 7939 EUR haE-1, respectively. However, the opposite was true for the net present value (r = 3%): 1423 EUR haE-1 and 304 EUR haE-1, respectively.