The Duration of Load (DOL) effect is the combined influence of the mechanical loading history and climatic history on the strength of materials. DOL effect is one of the most important characteristics of wood and wood-based materials. The material degradation or damage induces strength reductions. Creep is one of the most important effects of DOL. Creep is a phenomenon that negatively affects functional compliance, behaviour and strength of timber structures in extended years of exploitation. The creep phenomenon is affected by surrounding temperature, relative humidity, timber moisture content and other factors. The study aimed to establish a correct factor system for accurate prediction of long-term deformations of timber structures that is corresponding to environmental conditions and timber properties in the region of Latvia. The experimental research was made in Jelgava, Latvia, and represents timber beam four-point long-term loading in bending with variable cross section height-span length ratio under uncontrolled climatic conditions. There were 12 timber beams with two different span lengths – 1.32 m and 1.50 m used. The timber beam cross section dimensions: height – 60 mm, width – 30 mm. The timber beams were not dried and the moisture content at the start of the experiment varied from 19% to 33%. The applied load values – 0.40 kN and 0.31 kN. Moisture content fluctuations and negative air temperature accelerated creep development and intensity. Prediction of final long-term deformations should rate not only the type of timber material and service class but the strength class, too.

Invention of light weight panel with a trade mark of Dendrolight is one of the most distinguished wood industry innovations of the last decade. At present three layers cellular wood panels have wide non structural application. The aim of the research is to evaluate the bending properties of three layer cellular wood panels for structural application. There were 8 specimens manufactured with thickness 136 or 152 mm, width 300 mm and length 2,500 mm of each of the six horizontal load bearing panel structural models. Scots pine (Pinus sylvestris L.) cellular wood and solid pine wood ribs were used as internal layer of the structural panels. Cellular wood core was placed in horizontal or vertical direction. Scots pine solid wood panels and birch plywood were used as top layer material. Applied glue was polivinilacetate Cascol 3353. The most common stress type in structural subflooring panels is bending; therefore, the influence of the cellular material orientation, ribs and top layer material on the sandwich type structural panel bending strength (MOR) and stiffness (MOE) were evaluated according to LVS EN 408:2011. Extra parameters like moisture content and apparent density were determined. Cellular wood in vertical direction can be used as raw material for structural panel production. Panels with solid timber external layers, with ribs and with vertical orientation of the cellular material showed the highest MOR (35.2 N mmE-2) and MOE (11,500 N mmE-2) values. The influence of the solid wood ribs on the bending properties is directly dependent on external layer material.

Timber structure is a very complex system with its own specific character that causes a lot of difficulties for designers to predict its precise behaviour under loading. Timber construction behaviour under load is affected by many factors that in most cases influence timber constructions in a negative manner. Part of these influencing factors are properties of material, the other are components of the environment where the timber construction is located. This paper presents the results of experimental research where seventeen softwood (Pinus sylvestris L.) timber beams of rectangular cross section were tested in four point bending under long-term load in uncontrolled microclimate conditions (unheated building, all year round weather in the region of Latvia). Values of mechanical properties (modulus of elasticity), physical properties (density, amount of latewood, number of annual rings in 1 cm of wood) were measured at the start of the test; while monitoring of moisture content of wood, relative humidity and air temperature were performed simultaneously for the whole period of test. It has been observed that the main factors that significantly influence timber beam behaviour during period under load in natural climatic conditions are modulus of elasticity (MoE), density of wood and number of annual rings per 1 cm of wood. Amount of latewood showed an insignificant impact on timber beam behaviour under load.

Birch plywood has proved itself to be one of the most rational ways of wood processing. Growing demand of high performance birch plywood products requires a complex numerical analysis based on Finite Element Method (FEM), instead of using simple analytical assumptions, which prevent optimization of plywood construction (lay-up). In the research samples of birch plywood of several thicknesses, both sanded and non-sanded, with fibre direction of external veneer both in the longitudinal and transverse directions were tested. An extensometer and optical strain gauge were used for strain measurement. The FEM analysis, using commercial software SolidWorks Simulation Premium (SW), versus experimental bending and tension testing according to LVS EN 789 was carried out in this paper. The analysis of results indicates that there is a high correlation between the results of the experiments and the FEM. Particularly for in tension loaded specimens one can be tested up to the maximum ply strength (100 MPa); meanwhile, in bending up to 71MPa – the average stress in load bearing ply at the proportionality limit. Due to software restrictions, shear stresses cannot be evaluated. Future studies are considered to investigate terms for designing plywood with dynamic properties of strength and stiffness to be taken into account.

The manufacturers of wood-based panels are interested to get easy and cheap method for determination of characteristic values of panels. The correlation between European standards EN 789 and EN 310 tests results can be used as an alternative procedure for determination of characteristic values of bending properties. The correlations between two results of bending properties determined by testing methods of European standards EN 789 and EN 310 are studied in this paper. The ratio of EN 789 test results divided with EN 310 test results (ratio of EN 789/EN 310), depending on panel thickness and glue type, was examined. Samples from 846 panels of birch (Betula sp.) plywood with thickness ranging from 6.5 to 30 mm and two glue types - phenol formaldehyde and melamine urea formaldehyde resin - were used for verification of the correlations. The results show that the panel thickness influences the ratio of EN 789/EN 310 and the highest ratio were found between 12 and 15 mm panels. When the panel thickness is increased or decreased, the ratio of EN 789/EN 310 decreases significantly. The regression equations for each thickness of plywood are presented. The difference between plywood glued with phenol formaldehyde and melamine urea formaldehyde resin glues was not found.