In the market of the Latvia different wood surface coating materials suitable for use in outdoor conditions are offered, but available information on the efficiency of these against direct water exposure is insufficient. For structural timber building elements, such as glued laminated timber (GLT), the surface coating should be applied taking into account technological, visual or colour changes (ISO 7724:1984) and – last, but not least – economic aspects are considered. Wood surfaces coated with coating materials, such as varnishes, paints, etc. can stabilize some properties such as movement of moisture content, dimensional changes and attack by microorganisms and fungi. The changes in the moisture content of timber may influence such important parameters as mechanical properties and the total life time of the structural timber elements. A study has been conducted with the aim of assessing the efficiency of coating materials used for wood protection against water absorption. In this study, six different commercial coating products used for the treatment of spruce (Picea Abies L. Karst.) and pine (Pinus Sylvestris L.) samples were tested. The efficiency of different coating substances was assessed using two modified test methods according to the standards EN 382-2 (1994) and EN 927-5 (2006), determining the surface water absorption after immersion in water for 24 h and the dynamics of water absorption of the glued laminated timber for 696 h kept in water. As a result of the study, it has been ascertained that organic solvent-based commercial coating products are more efficient against short-term and long-term wood water absorption compared to oil-based coating materials.

In the market of the Latvia different wood surface coating materials suitable for use in outdoor conditions are offered, but available information on the efficiency of these against direct water exposure is insufficient. For structural timber building elements, such as glued laminated timber (GLT), the surface coating should be applied taking into account technological, visual or colour changes (ISO 7724:1984) and – last, but not least – economic aspects are considered. Wood surfaces coated with coating materials, such as varnishes, paints, etc. can stabilize some properties such as movement of moisture content, dimensional changes and attack by microorganisms and fungi. The changes in the moisture content of timber may influence such important parameters as mechanical properties and the total life time of the structural timber elements. A study has been conducted with the aim of assessing the efficiency of coating materials used for wood protection against water absorption. In this study, six different commercial coating products used for the treatment of spruce (Picea Abies L. Karst.) and pine (Pinus Sylvestris L.) samples were tested. The efficiency of different coating substances was assessed using two modified test methods according to the standards EN 382-2 (1994) and EN 927-5 (2006), determining the surface water absorption after immersion in water for 24 h and the dynamics of water absorption of the glued laminated timber for 696 h kept in water. As a result of the study, it has been ascertained that organic solvent-based commercial coating products are more efficient against short-term and long-term wood water absorption compared to oil-based coating materials.

An induction motor reliability survey at an egg processing plant shows that almost 50% of the total motor failures are fan induction motors. Visual investigations of the faulty fan motors show that the main cause of the induction motor failure is air gap eccentricity. In this study, experimental tests are performed on a 1.1kW three-phase induction motor to detect air gap eccentricity and overheating of the induction motor. Heating tests show that end shield housing temperature reaches 100°C with blocked air flow from the fan, which can reduce the lifespan of the bearing. Dimension measurements of the end shield housing show that the dimensions of both tested motors back-end shields are larger than ISO tolerance grade limit. It leads to a loose fit between the housing and bearing, causing air gap eccentricity. Also, both motor back end shield housing has an out-of-round condition leading to an unbalanced magnetic pull. To detect the air gap eccentricity caused by too loose of a fit between housing bore and bearing, current Park’s vector approach is used. To measure three phase current, Hall Effect current transducers, a digital oscilloscope is used and Matlab software to process the measurement data. Results show that Park’s vector approach can be used to detect the air gap eccentricity caused by too loose a fit between bearing and housing. Therefore, the Park’s vector approach can be used to diagnose air gap eccentricity and analyse the type of the air gap eccentricity.

An Induction motor reliability survey at an egg processing plant shows that almost 50% of the total motor failures are fan induction motors. Visual investigations of the faulty fan motors show that the main cause of the induction motor failure is air gap eccentricity. In this study, experimental tests are performed on a 1.1kW three-phase induction motor to detect air gap eccentricity and overheating of the induction motor. Heating tests show that end shield housing temperature reaches 100°C with blocked air flow from the fan, which can reduce the lifespan of the bearing. Dimension measurements of the end shield housing show that the dimensions of both tested motors back-end shields are larger than ISO tolerance grade limit. It leads to a loose fit between the housing and bearing, causing air gap eccentricity. Also, both motor back end shield housing has an out-of-round condition leading to an unbalanced magnetic pull. To detect the air gap eccentricity caused by too loose of a fit between housing bore and bearing, current Park’s vector approach is used. To measure three phase current, Hall Effect current transducers, a digital oscilloscope is used and Matlab software to process the measurement data. Results show that Park’s vector approach can be used to detect the air gap eccentricity caused by too loose a fit between bearing and housing. Therefore, the Park’s vector approach can be used to diagnose air gap eccentricity and analyse the type of the air gap eccentricity.