Objective: To compare the mechanical characteristics of polymerized caprolactam and monofilament nylon loops with those of the cranial cruciate ligament (CCL) in cattle. Sample: 6 femorotibial joints harvested from 3 cows and suture constructs made from No. 8 polymerized caprolactam, 80-lb test monofilament nylon fishing line, and 450-lb test monofilament nylon fishing line. Procedures: Joints were cleared of soft tissue structures except the CCL, connected to a load frame, and loaded to failure while measuring force and elongation. Synthetic constructs tested in a similar manner included single-stranded and 3-stranded No. 8 polymerized caprolactam, 3- and 6-stranded 80-lb test monofilament nylon fishing line, and 3- and 6-stranded 450-lb test monofilament nylon fishing line. Results: The CCL ruptured at a mean ± SD force of 4,541 ± 1,417 N with an elongation of 2.0 ± 0.3 cm. The tensile strength of 3-stranded 450-lb test monofilament nylon fishing line was similar to that of the CCL, rupturing at loads of 5,310 ± 369 N (braided strands) and 6,260 ± 239 N (parallel strands). Elongation was greater for braided constructs. Conclusions and Clinical Relevance: The 3-stranded cords of 450-lb test monofilament nylon fishing line most closely approximated the strength of the CCL. Marked increases in elongation occur when large-sized materials are constructed in braided configurations, and this elongation would likely not provide stability in CCL-deficient stifle joints. Additional studies are needed to determine whether any of these materials are suitable CCL replacements in cattle.

Objective: To determine whether parenteral l-alanyl-l-glutamine (Ala-Gln) administration modulated phagocytic responses of polymorphonuclear neutrophilic leukocytes (PMNs) from dogs undergoing high-dose methylprednisolone sodium succinate (MPSS) treatment. Animals: 15 healthy Beagles. Procedures: Dogs were randomly assigned to 3 treatment groups (n = 5/group): 38-hour IV infusion of saline (0.9% NaCl) solution (control group), saline solution with 8.5% amino acids (2.3 g/kg/d), or saline solution with 8.5% amino acids (1.8 g/kg/d) and 20% l-alanyl-l-glutamine (Ala-Gln; 0.5 g/kg/d). High-dose MPSS treatment was initiated at the same time that IV infusions began, such that a total dose of 85 mg of MPSS/kg was administered through multiple IV injections over a 26-hour period. The infusions were maintained until 12 hours after the last MPSS injection. Blood samples collected before MPSS injections began and 2, 12, and 24 hours after injections ceased were used to evaluate PMN function. Results: MPSS injections resulted in an increase in the total number of circulating leukocytes and increases in neutrophil and monocyte counts but did not affect lymphocyte, eosinophil, or basophil counts. Lymphocyte counts in the Ala-Gln group were higher than in the control group 12 hours after MPSS injections finished. Relative to preinfusion values, phagocytic capacity, oxidative burst activity, and filamentous actin polymerization of PMNs were suppressed in all dogs except those that received Ala-Gln. Conclusions and Clinical Relevance: Parenteral Ala-Gln administration in dogs resulted in an increase in PMN phagocytic responses that were suppressed by high-dose MPSS treatment.

With acrylic external-fixation frames for fracture repair the acrylic columns can be contoured to allow greater versatility in the placement of transfixation pins, thus minimizing damage to the surrounding soft tissue and making mandibular and transarticular fixation easier. However, contouring affects the stiffness and ultimate strength of the construct under axial compression. In this study, polymethylmethacrylate columns 21 mm in diameter angled at 0°, 30°, 45°, 60°, or 90° with clamps were constructed. For each angulation group, pins 3.2-mm long were placed in 6 columns, 2 pins at each end, 1.5 cm from each other, and 6 columns had no pins. Each column was allowed to polymerize for a minimum of 10 min, then was placed in a biomechanical-testing machine, the load cell at the bottom end of the column and the actuator on top, with a preload of 10 to 12 N to prevent slippage. The columns underwent axial loading at a rate of 8 mm/s until catastrophic failure occurred. Data on force and deformation were collected every 0.025 s. Both stiffness and ultimate strength of the column decreased significantly (P < 0.01), up to 77% and 70%, respectively, with each increase of angulation. The columns with pins were significantly less stiff (P < 0.05) than those without pins at angulations of 45° and 60°. However, the columns with pins did not show significant differences in ultimate strength from the columns without pins at any of the angulations. The point of failure was always at the angle of the column, demonstrating that in axial compression the weakest point is not the pin-acrylic interface when pins are eccentrically located within the column.