Serious pollution is caused by heavy metals (HMs) emission during sludge combustion treatment, but the addition of minerals has the ability to alleviate the migration of HMs to the gaseous state. In this study, HMs (As, Cr, Zn and Cu) behavior, speciation, and environmental risk during sludge combustion with CaO and montmorillonite (MMT) additive was investigated in the lab-scale tube furnace. The results showed that the sludge combustion was mainly determined by volatile matter. In general, CaO inhibited the volatilization of Cr, Zn, and Cu, but promoted As volatilization. MMT inhibited the volatilization of HMs, but the effect was not obvious at high temperatures. Besides, the improvement of retention effect was not found for Cr and Cu with the increase of CaO at 1000 °C, there might exist threshold value for CaO on HMs retention process. Meanwhile, CaO increased acid-soluble fraction of As significantly at high temperatures, decreased residual fraction of Cr by oxidation, converted Zn and Cu to residual fraction. MMT increased the acid-soluble fraction of As and residual fraction of Cr. In view of the HMs environmental risk in ash, the combustion temperature of sludge was necessary to control under 1000 °C and minerals additive amount was needed to manage above 1000 °C.

Converting biomass waste into biochar by slow pyrolysis with subsequent soil amendment is a prospective approach with multiple environmental benefits including soil contamination remediation, soil amelioration and carbon sequestration. This study selected cow manure as precursor to produce biochar under 300 °C, 400 °C, 500 °C and 600 °C, and a remarkable promotion of carbon (C) retention in biochar by incorporation of exogenous Ca was achieved at all investigated pyrolysis temperatures. The C retention was elevated from 49.2 to 68.3% of pristine biochars to 66.1–79.7% of Ca-composite biochars. It was interesting that extent of this improvement increased gradually with rising of pyrolysis temperature, i.e., doping Ca in biomass promoted pyrolytic C retention in biochar by 16.6%, 23.4%, 29.1% and 31.1% for 300 °C, 400 °C, 500 °C and 600 °C, respectively. Thermogravimetric-mass spectrometer (TG-MS) and X-ray photoelectron spectroscopy (XPS) showed that Ca catalyzed thermal-chemical reactions and simultaneously suppressed the release of small organic molecular substances (C₂–C₇) via physical blocking (CaO, CaCO₃, and CaClOH) and chemical bonding (CO and OC–O). The catalyzation mainly occurred at 200–400 °C, while the suppression was more prominent at higher temperatures. Raman spectra and 2D FTIR analysis on biochar microstructure showed that presence of Ca had negative influence on carbon aromatization and thus weakened biochar's stability, while increasing pyrolysis temperature enhanced the stability of carbon structure. Finally, with integrating “C retention” during pyrolysis and “C stability” in biochar, the maximum C sequestration (56.3%) was achieved at 600 °C with the participation of Ca. The study highlights the importance of both Ca and pyrolysis temperature in enhancing biochar's capacity of sequestrating C.

In this study, a proposed integrated high-gravity technology for air pollution control, CO2 capture, and alkaline waste utilization was comprehensively evaluated from engineering, environmental, and economic perspectives. After high-gravity technology and coal fly ash (CFA) leaching processes were integrated, flue gas air emissions removal (e.g., sulfate dioxide (SO2), nitrogen oxides (NOx), total suspended particulates (TSP)) and CO2 capture were studied. The CFA, which contains calcium oxide and thus, had high alkalinity, was used as an absorbent in removing air pollution residues. To elucidate the availability of technology for pilot-scale high-gravity processes, the engineering performance, environmental impact, and economic cost were simultaneously investigated. The results indicated that the maximal CO2, SO2, NOx, and TSP removal efficiencies of 96.3 ± 2.1%, 99.4 ± 0.3%, 95.9 ± 2.1%, and 83.4 ± 2.6% were respectively achieved. Moreover, a 112 kWh/t-CO2 energy consumption for a high-gravity process was evaluated, with capture capacities of 510 kg CO2 and 0.468 kg NOx per day. In addition, the fresh, water-treated, acid-treated, and carbonated CFA was utilized as supplementary cementitious materials in the blended cement mortar. The workability, durability, and compressive strength of 5% carbonated CFA blended into cement mortar showed superior performance, i.e., 53 MPa ±2.5 MPa at 56 days. Furthermore, a higher engineering performance with a lower environmental impact and lower economic cost could potentially be evaluated to determine the best available operating condition of the high-gravity process for air pollution reduction, CO2 capture, and waste utilization.

Waste streams associated with a variety of agricultural runoff sources are major contributors of nutrients, pesticides and enteric microorganisms to surface and ground waters. Water soluble anionic polyacrylamide (PAM) was found to be a highly effective erosion-preventing and infiltration-enhancing polymer, when applied at rates of 1-10 g m (super -3) in furrow irrigation water. Water flowing from PAM treated irrigation furrows show large reductions in sediment, nutrients and pesticides. Recently PAM and PAM+CaO and PAM+Al(SO (sub 4) ) (sub 3) mixtures have been shown to filter bacteria, fungi and nutrients from animal wastewater. Low concentrations of PAM [175-350 g PAM ha (super -1) as PAM or as PAM+CaO and PAM+Al(SO (sub 4) ) mixture] applied to the soil surface, resulted in dramatic decreases (10 fold) of total, coliform and fecal streptococci bacteria in cattle, fish and swine wastewater leachate and surface runoff. PAM treatment also filtered significant amounts of NH (sub 4) , PO (sub 4) and total P in cattle and swine wastewater. This points to the potential of developing PAM as a water quality protection measure in combination with large-scale animal feeding operations. Potential benefits of PAM treatment of animal facility waste streams include: (1) low cost, (2) easy and quick application, (3) suitability for use with other pollution reduction techniques. Research on the efficacy of PAM for removal of protozoan parasites and viruses and more thorough assessment of PAM degradation in different soils is still needed to completely evaluate PAM treatment as an effective waste water treatment. We will present analysis and feasibility of using PAM, PAM+Al(SO (sub 4) ) (sub 3) , and PAM+CaO application for specific applications. Our results demonstrate their potential efficacy in reducing sediment, nutrients and microorganisms from animal production facility effluents. Abstract

Soil chemistry of toxic metalloids and metals differs, making their simultaneous removal difficult. Soil contaminated with As, Pb, Zn and Cd was washed with oxalic acid, Na-dithionite and EDTA solution. Toxic elements were removed from the washing solution by alkalinisation with CaO to a pH 12.5: As was co-precipitated with Fe from Fe-EDTA chelate formed after the soil washing. The toxic metals precipitated after substitution of their EDTA chelates with Ca. The novel method was scaled up on the ReSoil® platform. On average, 60, 76, 29, and 53% of As, Pb, Zn, and Cd were removed, no wastewater was generated and EDTA was recycled. Addition of zero-valent iron reduced the toxic elements’ leachability. Remediation was most effective for As: phytoaccessibility (CaCl₂ extraction), mobility (NH₄NO₃), and accessibility from human gastric and gastrointestinal phases were reduced 22, 104, 6, and 51 times, respectively. Remediation increased pH but had no effect on soil functioning assessed by fluorescein diacetate hydrolysis, dehydrogenase, β-glucosidase, urease, acid and alkaline phosphatase activities. Brassica napus produced 1.9 times more biomass on remediated soil, accumulated no As and 5.0, 2.6, and 9.0 times less Pb, Zn and Cd, respectively. We demonstrated the novel remediation technology as cost-efficient (material cost = 41.86 € t⁻¹) and sustainable.

The adverse health effects associated with the inhalation and ingestion of naturally occurring radon gas produced during the uranium decay chain mean that there is a need to identify high-risk areas. This study detected radon-prone areas using a geographic information system (GIS)-based probabilistic and machine learning methods, including the frequency ratio (FR) model and a convolutional neural network (CNN). Ten influencing factors, namely elevation, slope, the topographic wetness index (TWI), valley depth, fault density, lithology, and the average soil copper (Cu), calcium oxide (Cao), ferric oxide (Fe₂O₃), and lead (Pb) concentrations, were analyzed. In total, 27 rock samples with high activity concentration index values were divided randomly into training and validation datasets (70:30 ratio) to train the models. Areas were categorized as very high, high, moderate, low, and very low radon areas. According to the models, approximately 40% of the study area was classified as very high or high risk. Finally, the radon potential maps were validated using the area under the receiver operating characteristic curve (AUC) analysis. This showed that the CNN algorithm was superior to the FR method; for the former, AUC values of 0.844 and 0.840 were obtained using the training and validation datasets, respectively. However, both algorithms had high predictive power. Slope, lithology, and TWI were the best predictors of radon-affected areas. These results provide new information regarding the spatial distribution of radon, and could inform the development of new residential areas. Radon screening is important to reduce public exposure to high levels of naturally occurring radiation.

Cadmium (Cd) contamination in soil and crops caused by mining activities has become a prevalent concern in the world. Given that different crops have varying Cd bioaccumulation factors, crops with low Cd bioaccumulation abilities can be selected for the safe usage of Cd -contaminated lands. This study aimed to investigate Cd contamination in soil and crops and the influencing factors of soil Cd activity in a tin mining area (TMA) and control area (CA) and to put forward suggestions for the safe usage of farmlands by developing prediction models of Cd content in different crop grains. We collected 72 and 40 pairs of rice and maize grain samples, respectively, along with their rhizosphere soil samples and 6176 topsoil samples. The results showed that compared with the CA, the Cd pollution was more severe in the cultivated soil and crop grains around TMA. Furthermore, rice has a strong ability to transport Cd from soil to grains, whereas maize has a poor Cd uptake ability. The total organic carbon, CaO, pH, and Mn in soil play key roles in the transfer of Cd from soil to crop grains. Using these parameters and Cd concentration in soil, two sets of accurate Cd prediction models were developed for maize and rice. Based on the Cd concentration in the topsoil and predicted Cd concentration in crop grains, the safe utilization scheme of farmland was proposed. The proportions of priority protection, safe exploitation, planting adjustment, and strict control were 72.59%, 22.77%, 3.16%, and 1.48% in the TMA, respectively. The values reached 80.51% (priority protection), 19.12% (safe exploitation), 0.37% (planting adjustment), and 0% (strict control) in the CA. Thus, given the difference between Cd accumulation in rice and maize, adjustment of planting crops in contaminated farmlands can be applied to maximize the use of farmland resources.

Industrial by-products provide materials for remediation measures. In this study, a silicon-iron amendment was prepared from residue originating from acid-extracted copper (Cu) tailings based on thermal activation at temperatures ranging from 550 °C to 1150 °C for 30 min with the use of additives (CaO, Na₂CO₃, NaOH). The remediation performance of the amendment was evaluated through soil incubation and greenhouse pot experiments with vetiver (Vetiveria zizanioides). The results showed that the highest levels of soluble Si (6.11% of the total Si) and Fe (2.3% of the total Fe) in the amendment were achieved with thermal activation at 1150 °C for 30 min using an optimal ratio between residue and additives (residue: CaO: Na₂CO₃: NaOH = 1: 0.4: 0.4: 0.2). Heavy metal release indicated that the amendment could be safely used for soil remediation. The incubation experiments showed that the DTPA-extractable Cd, Cr and Pb in contaminated soils decreased with increasing amendment rate, which was not observed for As. The amendment-induced decrease in the Cd, Cr and Pb availability in contaminated soils could be explained by pH-change induced immobilization, Fe-induced chemisorption, Si-induced co-precipitation, and Ca-induced ion exchange. Correlation analysis suggested that there were significant negative correlations between DTPA-extractable Cd, Cr and Pb and the pH, Fe, Si, and Ca in soil pore water and soil. The most suitable amendment rate was determined to be 1% by balancing the efficacy and wise utilization of the amendment. The pot experiment demonstrated that the amendment promoted the vetiver growth and stimulated the accumulation of Cd and Cr in the roots. The amendment was proved to be promising for the phytostabilization of Cd, Cr and Pb in contaminated soils. Further investigations are required to determine whether the amendment is a tool for the long-term remediation of multi-metal-contaminated soils at the field scale.

In this study, the detoxification mechanisms of water-soluble fluorine in the bottom ash and the distribution of fluorine during the spent potlining (SPL) incineration were characterized in response to four calcium compounds using an experimental tube furnace. CaSiO₃, CaO, Ca(OH)₂, and CaCO₃-assisted SPL incineration converted NaF to low toxicity compounds in the bottom ash yielding a conversion range of 54.24–99.45% relative to the individual SPL incineration. The two main mechanisms of the fluorine transformation were the formations of CaF₂ and Ca₄Si₂O₇F₂. The fluorine transformation efficiency was greater with CaSiO₃ than CaO, Ca(OH)₂, and CaCO₃. Our simulations demonstrated that SiO₂ enhanced the conversion of NaF. The fluorine leaching content of the bottom ash was estimated at 13.71 mg⋅L⁻¹ after the SPL co-incineration with CaSiO₃ (Ca:F = 1.2:1). The acid-alkali solutions had no significant effect on the fluorine leaching content of the bottom ash when 3 ≤ pH ≤ 12. Fluorine during the SPL co-incineration with CaSiO₃ (Ca:F = 1.2:1) at 850 °C for 60 min was partitioned into 83.37, 13.90, and 2.72% in the bottom ash, fly ash, and flue gas, respectively. The transformation and detoxification mechanisms of water-soluble fluorine provide new insights into controls on fluorine emission from the SPL incineration.

Toxic metals have been linked to a range of adverse health effects in freshwater organisms. However, for higher vertebrates, there is little understanding of the large-scale drivers of exposure. We quantified toxic metal/semi-metal concentrations in a sentinel freshwater top predator, the Eurasian otter (Lutra lutra), across England and Wales, and determined how this varied with key natural and anthropogenic factors. We related liver concentrations in 278 otters that died between 2006 and 2017 to habitat biogeochemistry, proximity to point source contamination and to biological characteristics (length, sex, condition). Evidence for any positive association with putative anthropogenic sources (mining, human population, known discharges) was weak or lacking in nearly all cases, with the exception of a positive association between lead and human population density. Despite concerns that burgeoning use of nanosilver in consumer products might increase silver concentrations in waste waters, there was no increase over time. Spatial variation in soil/sediment pH, precipitation, and soil calcium oxide are indicated as significant predictors of metal concentrations in otters (higher cadmium and silver in areas with lower pH and higher rainfall, and higher chromium and lead in areas of lower calcium oxide). Liver chromium and nickel concentrations declined significantly over time (Cr 0.030 ± 1.2 to 0.015 ± 1.3 μg/g dry weight, Ni 0.0038 ± 1.2 to 0.00068 ± 1.5 μg/g, between 2006–2009 and 2014–2017), but other metals showed no temporal change. Biotic associations were important, with age related accumulation indicated for mercury and cadmium (as well as interactions with body condition). Our results suggest that larger-scale geochemical and hydrological processes are important in determining metal exposure in otters, and we provide an indication of risk factors that may be of relevance for freshwater vertebrates in other countries with well-developed water pollution management.