Refinar búsqueda
Resultados 1-10 de 138
Biological toxicity risk assessment of two potential neutral carbon diesel fuel substitutes
2022
Arias, Silvana | Estrada, Verónica | Ortiz, Isabel C. | Molina, Francisco J. | Agudelo, John R.
We investigated the biological response of soluble organic fraction (SOF) and water-soluble fraction (WSF) extracted from particulate matter (PM) emitted by an automotive diesel engine operating in a representative urban driving condition. The engine was fueled with ultra-low sulfur diesel (ULSD), and its binary blends by volume with 13% of butanol (Bu13), and with hydrotreated vegetable oil (HVO) at 13% (HVO13) and 20% (HVO20). Cytotoxicity, genotoxicity, oxidative DNA damage and ecotoxicity tests were carried out, and 16 polycyclic aromatic hydrocarbons (PAH) expressed as tbenzo(a)pyrene total toxicity equivalent (BaP-TEQ) were also analyzed. The Hepatocarcinoma epithelial cell line (HepG2) was exposed to SOF for 24 h and analyzed using comet assay, with the inclusion of formamidopyrimidine DNA glycosylase (FPG) and endonuclease III (Endo III) to recognize oxidized DNA bases. The WSF was evaluated through acute ecotoxicity tests with the aquatic microcrustacean Daphnia pulex (D. Pulex). Results showed that there was no cytotoxic activity for all tested SOF concentrations. Genotoxic responses by all the SOF samples were at same level, except for the HVO13 which was weaker in the absence of the enzymes. The addition of the FPG and Endo III enzymes resulted in a significant increase in the comet tail, indicating that the DNA damage from SOF for all tested fuel blends involves oxidative damage including a higher level of oxidized purines for ULSD and Bu13 in comparison with HVO blends, but the oxidized pyrimidines for HVO blends were slightly higher compared to Bu13. The WSF did not show acute ecotoxicity for any of the fuels. Unlike other samples, Bu13-derived particles significantly increase the BaP-TEQ. The contribution to the genotoxic activity and oxidative DNA from SOF was not correlated to BaP-TEQ, which means that the biological activity of PM might be affected also by other toxic compounds present in particulate phase.
Mostrar más [+] Menos [-]Soot particle morphology and nanostructure with oxygenated fuels: A comparative study into cold-start and hot-start operation
2021
Verma, Puneet | Jafari, Mohammad | Zare, Ali | Pickering, Edmund | Guo, Yi | Osuagwu, Chiemeriwo Godday | Stevanovic, Svetlana | Brown, Richard | Ristovski, Zoran
This study investigates the morphology and nanostructure of soot particles during cold-start and hot-start engine operation of a diesel engine using oxygenated fuels. The soot samples were analysed using transmission electron microscopy. The oxygen content in the fuel was varied between 0 and 12%. The results showed that the primary particles during cold-start have significantly smaller size when compared to hot-start engine operation. The addition of oxygenated fuels also resulted in smaller sized primary particles. Smaller radius of gyration and higher fractal dimension of soot aggregates during cold-start would mean smaller aggregate size with a more compact structure. Shorter fringes with a higher inter-fringe spacing for cold-start would mean lower graphitisation of soot particles that could be related to higher oxidation reactivity of soot particles.
Mostrar más [+] Menos [-]Mechanism of accelerating soot oxidation by NO2 from diesel engine exhaust
2020
Li, Zehong | Zhang, Wei | Chen, Zhaohui | Jiang, Qianyu
NO₂ oxidation of soot exhausted from engines is more efficient than O₂ under low-temperature conditions, and is crucial for diesel particulate filter to control soot pollution. To explore the principle behind accelerating soot oxidation by NO₂, this paper uses density functional theory to reveal soot oxidation process by NO₂. This study contributes to understanding rules of soot oxidation by NO₂ and perfecting soot oxidation models to develop soot emission control technologies. Results show that NO₂ oxidation of pyrene radical involves three steps. Firstly, NO₂ attacks the C∗ atom to form –C (NO₂) with reaction energy of 306.3 kJ/mol, which decomposes to produce a –C (O) compound. Secondly, another NO₂ molecule climbs over an energy barrier of 8.8 kJ/mol, and changes into a –C (ONO₂) intermediate on –C (O). Finally, the N or O atom of NO₂ attacks –C (O) for a second time to help open aromatic ring for releasing CO or CO₂. Further decomposition of –C (NO₂) and –C (ONO₂) requires activation energies of 81.6 kJ/mol, 75.7 kJ/mol, and 53.5 kJ/mol, respectively, on preferential pathways. Calculations prove that attacks of O atom from NO₂ on C∗ help open the aromatic ring more efficiently than N atom.
Mostrar más [+] Menos [-]Particulate characteristics of low-temperature combustion (PCCI and RCCI) strategies in single cylinder research engine for developing sustainable and cleaner transportation solution
2021
Agarwal, Avinash Kumar | Singh, Akhilendra Pratap | Kumar, Vikram
In this experimental study, particulate matter (PM) characterizations of different low-temperature combustion (LTC) strategies have been compared with conventional compression ignition (CI) combustion for finding out a sustainable and cleaner transport solution. LTC strategies included premixed charge compression ignition (PCCI) and reactivity-controlled compression ignition (RCCI) combustion. Particulate sampling and characterization were carried out in a single-cylinder diesel engine. All engine tests were performed at 1, 2, 3, 4 bar brake mean effective pressure (BMEP) at 1500 rpm. CI and PCCI combustion experiments were performed using mineral diesel as the test fuel. However, mineral diesel and methanol were used as high reactivity fuel (HRF) and low reactivity fuel (LRF), respectively in the RCCI combustion strategy. For all combustion strategies, fuel injection pressure (FIP) was kept constant at 500 bar. However, the number of injections and start of injection (SoI) timings were varied to optimize the engine performance. Results showed that the RCCI combustion strategy emitted a relatively lower concentration of particles than the other two strategies (PCCI and CI). A relatively higher number concentration of accumulation mode particles (AMP) compared to nucleation mode particles (NMP) in the exhaust of the RCCI combustion strategy was an important finding of this study. Number-size and mass-size distributions of particles emitted from different strategies also exhibited the dominant concentration of particles in the CI combustion strategy. PM bound trace metal analysis was yet another critical aspect of this study, which showed that both RCCI and PCCI strategies emitted a relatively lower concentration of trace metals than the conventional CI combustion strategy. Parametric analysis of different PM characteristics and NOx-PM trade-off analysis also demonstrated the importance of LTC strategies over the conventional CI combustion strategy. Overall, this study demonstrated that all LTC strategies could be used for PM and NOx reduction; however, the RCCI combustion strategy was more dominant in NOx and PM reduction, in addition to having an excellent capability of using alternative fuel in the quest for developing sustainable transport solution.
Mostrar más [+] Menos [-]Source apportionment of fine particulate matter organic carbon in Shenzhen, China by chemical mass balance and radiocarbon methods
2018
Al-Naiema, Ibrahim M. | Yoon, Subin | Wang, Yu-Qin | Zhang, Yuan-Xun | Sheesley, Rebecca J. | Stone, Elizabeth A.
Chemical mass balance (CMB) modeling and radiocarbon measurements were combined to evaluate the sources of carbonaceous fine particulate matter (PM2.5) in Shenzhen, China during and after the 2011 summer Universiade games when air pollution control measurements were implemented to achieve air quality targets. Ambient PM2.5 filter samples were collected daily at two sampling sites (Peking University Shenzhen campus and Longgang) over 24 consecutive days, covering the controlled and uncontrolled periods. During the controlled period, the average PM2.5 concentration was less than half of what it was after the controls were lifted. Organic carbon (OC), organic molecular markers (e.g., levoglucosan, hopanes, polycyclic aromatic hydrocarbons), and secondary organic carbon (SOC) tracers were all significantly lower during the controlled period. After pollution controls ended, at Peking University, OC source contributions included gasoline and diesel engines (24%), coal combustion (6%), biomass burning (12.2%), vegetative detritus (2%), biogenic SOC (from isoprene, α-pinene, and β-caryophyllene; 7.1%), aromatic SOC (23%), and other sources not included in the model (25%). At Longgang after the controls ended, similar source contributions were observed: gasoline and diesel engines (23%), coal combustion (7%), biomass burning (17.7%), vegetative detritus (1%), biogenic SOC (from isoprene, α-pinene, and β-caryophyllene; 5.3%), aromatic SOC (13%), and other sources (33%). The contributions of the following sources were smaller during the pollution controls: biogenic SOC (by a factor of 10–16), aromatic SOC (4–12), coal combustion (1.5–6.8), and biomass burning (2.3–4.9). CMB model results and radiocarbon measurements both indicated that fossil carbon dominated over modern carbon, regardless of pollution controls. However, the CMB model needs further improvement to apportion contemporary carbon (i.e. biomass burning, biogenic SOC) in this region. This work defines the major contributors to carbonaceous PM2.5 in Shenzhen and demonstrates that control measures for primary emissions could significantly reduce secondary organic aerosol (SOA) formation.
Mostrar más [+] Menos [-]Toxicity and mutagenicity of exhaust from compressed natural gas: Could this be a clean solution for megacities with mixed-traffic conditions?
2018
Agarwal, Avinash K. | Ateeq, Bushra | Gupta, Tarun | Singh, Akhilendra P. | Pandey, Swaroop K. | Sharma, Nikhil | Agarwal, Rashmi A. | Gupta, Neeraj K. | Sharma, Hemant | Jain, Ayush | Shukla, Pravesh C.
Despite intensive research carried out on particulates, correlation between engine-out particulate emissions and adverse health effects is not well understood yet. Particulate emissions hold enormous significance for mega-cities like Delhi that have immense traffic diversity. Entire public transportation system involving taxis, three-wheelers, and buses has been switched from conventional liquid fuels to compressed natural gas (CNG) in the Mega-city of Delhi. In this study, the particulate characterization was carried out on variety of engines including three diesel engines complying with Euro-II, Euro-III and Euro-IV emission norms, one Euro-II gasoline engine and one Euro-IV CNG engine. Physical, chemical and biological characterizations of particulates were performed to assess the particulate toxicity. The mutagenic potential of particulate samples was investigated at different concentrations using two different Salmonella strains, TA98 and TA100 in presence and absence of liver S9 metabolic enzyme fraction. Particulates emitted from diesel and gasoline engines showed higher mutagenicity, while those from CNG engine showed negligible mutagenicity compared to other test fuels and engine configurations. Polycyclic aromatic hydrocarbons (PAHs) adsorbed onto CNG engine particulates were also relatively fewer compared to those from equivalent diesel and gasoline engines. Taken together, our findings indicate that CNG is comparatively safer fuel compared to diesel and gasoline and can offer a cleaner transport energy solution for mega-cities with mixed-traffic conditions, especially in developing countries.
Mostrar más [+] Menos [-]The effects of biodiesels on semivolatile and nonvolatile particulate matter emissions from a light-duty diesel engine
2017
Cheng, Yuan | Li, Shao-Meng | Liggio, John | Hayden, Katherine | Han, Yuemei | Stroud, Craig | Chan, Tak | Poitras, Marie-Josée
Semivolatile organic compounds (SVOCs) represent a dominant category of secondary organic aerosol precursors that are increasingly included in air quality models. In the present study, an experimental system was developed and applied to a light-duty diesel engine to determine the emission factors of particulate SVOCs (pSVOCs) and nonvolatile particulate matter (PM) components at dilution ratios representative of ambient conditions. The engine was tested under three steady-state operation modes, using ultra-low-sulfur diesel (ULSD), three types of pure biodiesels and their blends with ULSD. For ULSD, the contribution of pSVOCs to total particulate organic matter (POM) mass in the engine exhaust ranged between 21 and 85%. Evaporation of pSVOCs from the diesel particles during dilution led to decreases in the hydrogen to carbon ratio of POM and the PM number emission factor of the particles. Substituting biodiesels for ULSD could increase pSVOCs emissions but brought on large reductions in black carbon (BC) emissions. Among the biodiesels tested, tallow/used cooking oil (UCO) biodiesel showed advantages over soybean and canola biodiesels in terms of both pSVOCs and nonvolatile PM emissions. It is noteworthy that PM properties, such as particle size and BC mass fraction, differed substantially between emissions from conventional diesel and biodiesels.
Mostrar más [+] Menos [-]Effect of diesel blended with di-n-butyl ether/1-octanol on combustion and emission in a heavy-duty diesel engine
2022
Wang, Jinglan | Sun, Lifang | Luan, Pengpeng | Wu, Yangyi | Cheng, Zhanjun | Zhang, Zhao | Kong, Xiangen | Liu, Haifeng | Chen, Guanyi
Two kinds of C₈ isomers, di-n-butyl ether (DNBE) and 1-octanol, as potential oxygen-containing alternative fuels, show important value in the trade-off between efficiency and emission. In the present work, the effects of DNBE/1-octanol with different proportions (0, 10%, and 20%) blended into diesel on the combustion characteristics, fuel economy, and emission characteristics in a six-cylinder heavy-duty diesel engine were studied at low, medium, and high loads. 1-Octanol with a 20% blending ratio showed different combustion characteristics in the cylinder compared with the other fuels. The economic analysis showed that the brake specific fuel consumption of DNBE–diesel blend fuels was higher than that of 1-octanol–diesel blend fuels, while brake thermal efficiency was the opposite tendency. The emissions of nitrogen oxides (NOx), hydrocarbons (HC), and carbon monoxide (CO) were affected by the types of blend fuels, blending ratios, and loads. In comparison with 1-octanol–diesel blend fuels, the addition of DNBE in diesel promoted the emission of nitrogen oxides, but inhibited the emissions of soot, HC, and CO. DNBE– and 1-octanol–diesel blend fuels increased the weighted brake specific fuel consumption but decreased the weighted brake thermal efficiency compared with diesel in the World Harmonized Stationary Cycle test cycle of Euro VI regulation. The weighted NOx, HC, soot, and CO emissions of blend fuels depended on the types of blend fuels and blend ratios. The weighted NOx, HC, and soot emissions were reduced by blending 1-octanol into diesel, while the weighted CO emission was increased. The weighted CO and soot emissions of diesel blended with DNBE were reduced than that of diesel.
Mostrar más [+] Menos [-]Analysis of cold-start NO2 and NOx emissions, and the NO2/NOx ratio in a diesel engine powered with different diesel-biodiesel blends
2021
Zare, Ali | Stevanovic, Svetlana | Jafari, Mohammad | Verma, Puneet | Babaie, Meisam | Yang, Liping | Rahman, M.M. | Ristovski, Zoran D. | Brown, Richard J. | Bodisco, Timothy A.
In the transportation sector, the share of biofuels such as biodiesel is increasing and it is known that such fuels significantly affect NOx emissions. In addition to NOx emission from diesel engines, which is a significant challenge to vehicle manufacturers in the most recent emissions regulation (Euro 6.2), this study investigates NO₂ which is a toxic emission that is currently unregulated but is a focus to be regulated in the next regulation (Euro 7). This manuscript studies how the increasing share of biofuels affects the NO₂, NOx, and NO₂/NOx ratio during cold-start (in which the after-treatment systems are not well-effective and mostly happens in urban areas). Using a turbocharged cummins diesel engine (with common-rail system) fueled with diesel and biofuel derived from coconut (10 and 20% blending ratio), this study divides the engine warm-up period into 7 stages and investigates official cold- and hot-operation periods in addition to some intermediate stages that are not defined as cold in the regulation and also cannot be considered as hot-operation. Engine coolant, lubricating oil and exhaust temperatures, injection timing, cylinder pressure, and rate of heat release data were used to explain the observed trends. Results showed that cold-operation NOx, NO₂, and NO₂/NOx ratio were 31–60%, 1.14–2.42 times, and 3–8% higher than the hot-operation, respectively. In most stages, NO₂ and the NO₂/NOx ratio with diesel had the lowest value and they increased with an increase of biofuel in the blend. An injection strategy change significantly shifted the in-cylinder pressure and heat release diagrams, aligned with the sudden NOx drop during the engine warm-up. The adverse effect of cold-operation on NOx emissions increased with increasing biofuel share.
Mostrar más [+] Menos [-]Accurate prediction of NOx emissions from diesel engines considering in-cylinder ion current
2020
Mohammadi, Milad | Neshat, Elaheh
The main purpose of current study is accurate prediction of NOx emissions from diesel engines considering in-cylinder ion current. To reach this goal, a validated thermodynamic multi-zone model was used. A modified chemical kinetics mechanism of diesel fuel oxidation was used too. A chemical kinetics mechanism of NOX formation including 103 reactions was added to the main mechanism. A set of ions and ionic reactions was added to the developed chemical kinetics mechanism and finally a modified chemical kinetics mechanism with 445 reactions and 100 species was formed. The developed mechanism was coupled to the multi-zone model and a diesel engine was simulated. The importance of Zeldovich mechanism, prompt mechanism, N₂O mechanism and NNH mechanism were investigated. The progress rates of reactions were calculated and important reactions were identified. The results show that the oxygenated ions, NO⁺, O⁺ and O₂⁺, has more effects on NO production than other ions. The prompt mechanism plays an important role in predicting the ion current inside the chamber. Because this mechanism has reactions that can lead to CH production. The CH radicals produced by this mechanism can be employed by basic ionic reactions and lead to ion production. The results show that using NOx related ionic reactions results in accurate prediction of engine exhaust NOx.
Mostrar más [+] Menos [-]