Refinar búsqueda
Resultados 1-10 de 19
A modified exergy evaluation of using carbon-black/water/EG nanofluids as coolant of photovoltaic modules
2022
To provide the progressive global demand for energy, the use of renewable energies is being rapidly developed. Since solar radiation is available in most parts of the earth, the photovoltaic (PV) power plant is one of the worthwhile solutions. As a deficiency, temperature rise in photovoltaic cells leads to a drop in their electrical output power. In this experimental study, the circulation of carbon black nanofluid was investigated as a coolant of PV modules. Both water and ethylene glycol (EG) were used as the base fluids. It is found that all modified cases generate more output power than the conventional one. For instance, water + carbon nanofluid yields 54% more output power compared with the conventional one. To make a real assessment of using nanofluid as a coolant, the electrical consumption by pump and fan must be counted. Therefore, in this study, the net output power is calculated. In the cases of EG and EG + carbon, the net output powers get lower than the conventional module. So, they are not justifiable. In this paper, a modified formula is proposed to calculate the exergy efficiency, in order to achieve more accurate results. Accordingly, from an exergy viewpoint, 16.3% and 4.5% in electrical and thermal exergy efficiencies are achieved, when water + carbon nanofluid was used. Moreover, the values of entropy generation and lost exergy were reported for all considered cases.
Mostrar más [+] Menos [-]Effect of active multi-walled carbon nanotubes (MWCNT) on the energy storage density of DI water for cool thermal storage system
2022
Sathishkumar, Anbalagan | Cheralathan, Marimuthu
The present research work aims to investigate the energy saving aspects in cool thermal energy storage system (CTES) by improving the thermophysical properties of deionized (DI) water. The influence of phase change enthalpy, specific heat, thermal conductivity, and cooling rate of the DI water for the dispersion of chemically functionalized multi-walled carbon nanotubes (f-MWCNT) is studied experimentally. The covalent functionalization method is used to modify the surface of the multi-walled carbon nanotubes (MWCNT) with the use of concentrated nitric acid. The nanofluid phase change materials (PCMs) in different mass concentrations (0.25%, 0.50%, and 0.75%) were prepared by dispersions of the f-MWCNT in DI water. The minimum reduction in enthalpy (4.01%) was recorded for the nano-PCM with 0.75% f-MWCNT as compared to the base PCM with 0.5% of sodium dodecyl benzene-sulfonate (10%). The thermal conductivity enhancement of 53.15% and 28.2% was recorded in both states for the nano-PCM (with 0.75%) at the temperature of − 10 °C and 5 °C respectively. Also, the enhancement of 30% and 23% in cooling rate is recorded for the dispersion of maximum concentration of f-MWCNT at the HTF temperatures of − 8 °C and − 6 °C, respectively. It is proven from the above findings that the dispersion of f-MWCNT reduces the subcooling and facilitates the running of the CTES system at a higher operating temperature.
Mostrar más [+] Menos [-]Exploring the thermo-physical characteristic of novel multi-wall carbon nanotube—Therminol-55-based nanofluids for solar-thermal applications
2022
GaneshKumar, Poongavanam | Sakthivadivel, Duraiswamy | Prabakaran, Rajendran | Vigneswaran, Shanmugarajan | SakthiPriya, Manivannan | Thakur, Amrit Kumar | Sathyamurthy, Ravishankar | Kim, Sung Chul
This work aims to develop a novel nanofluid using Therminol-55 (T-55) as heat transfer fluid and multi-wall carbon nanotubes (MWCNTs) as dispersants with various volume concentrations of 0.05, 0.1, 0.3, and 0.5% and assess its thermo-physical properties for solar-thermal applications. The pH values of nanofluid MWCNT/T-55 with various particle loading were too far-flung from the pH (I) value, which confirmed the good dispersion stability of nanofluid. The measured density shows tremendous deviation from predicted density with increasing MWCNT loading owing to the non-considering of microstructural parameters in Pak & Cho correlation predication. The highest augmentation in nanofluid thermal conductivity was 16.83% for 0.5 vol. % MWCNT at 60 °C. The maximum improvement in dynamic viscosity of nanofluid with 0.5 vol. % of MWCNT is found to be 44%, and this rise is reduced at higher temperatures. The thermal effectiveness of the nanofluids demonstrates that nanofluid with all volume fractions of MWCNTs was favorable at higher temperatures in the laminar region. Mouromtseff number ratio decreases with a rise in temperature and MWCNT volume concentration. It is concluded that the excellent thermo-physical properties and prolonged thermal stability of the MWCNT will be highly beneficial in improving the overall performance of various kinds of heat transfer fluids (HTFs) for process heating and solar-thermal applications.
Mostrar más [+] Menos [-]Performance enhancement of the photovoltaic system with different cooling methods
2022
Tiwari, Sumit | Swaminathan, Muthukarupan | S, Santhosh Eashwar | Harender, | Singh, Desh Bandhu
Solar energy has been a vital renewable energy source for humanity for decades. Researchers have proposed many strategies to harness the same but solar photovoltaic (PV) is the only technology which has reached commercial scale and highly successful in meeting renewable energy goals of many countries. The major drawback of PV systems is that increase in the temperature of solar cell of the PV module beyond the threshold limit brings down its electrical efficiency (EE). Hence, this review paper discusses the different cooling techniques responsible for reducing the cell temperature, which in turn increases not only its EE, but also collection of the thermal energy that is otherwise considered to dampen the performance of the PV system. A brief study on PV with air cooling, photovoltaic thermal (PVT) with water cooling, PVT/PCM with and without fins, PVT integrated with nanofluids has been done in this review paper. PVT hybrid systems are the need of hour to get the optimum efficiency. Amongst the PVT systems, the performance analysis of PV integrated with the nanofluid is discussed and it is found to give the maximum cell temperature reduction. Since reduction in the cell temperature directly relates to better efficiency, PVT system using nanofluid as a cooling medium gives the best overall efficiency (OE) followed by PVT system incorporating water and air respectively. This review paper also gives spotlight to the real-time usages of PCM and nanofluids for the effective cooling ability especially in the case of PV module.
Mostrar más [+] Menos [-]Solar parabolic dish collector for concentrated solar thermal systems: a review and recommendations
2022
Kumar, Kolli Harish | Daabo, Ahmed M. | Karmakar, Malay K. | Hirani, Harish
Energy demand in the present scenario is rising to meet the increasing demands of energy usage. On the other hand, the use for renewable energy sources now becomes essential to mitigate the climate change as well as to reduce gradual depletion of fossil fuels. Among these renewable energy sources, solar energy particularly solar thermal systems have phenomenal scope in present and future research. In solar thermal systems, concentrators are used to extract the energy from solar irradiation and convert it into useful form. Among different types of solar concentrators, the parabolic dish solar concentrator is preferred as it has high efficiency, high power density, low maintenance, and potential for long durability. In this paper, a detailed review has been carried out on the design parameters like focal length, concentration ratio, and rim angle of the parabolic dish solar concentrator system for achieving higher overall efficiency. The effects of different geometrical shapes of receivers on the overall heat transfer rates are discussed in this paper. Conical shaped receiver is having high overall optical and thermal efficiency comparing with other shapes of receivers. This study also shows that how the thermal performance of the receiver gets enhanced by 10–13% using nanofluids in place of general heat transfer fluids. The paper highlights different models using ray-tracing method for estimation and evaluation of the solar irradiation distribution on the receiver surface. The empirical relations for the design of parabolic dish solar concentrator system are derived for estimating overall concentrator efficiency and heat available at the receiver are given in this review. From the literature, the thermal performance of the receiver affecting the overall performance of the system is observed. Thermal losses due to geometrical properties and ordination of the receiver are explained in the observation section.
Mostrar más [+] Menos [-]A comparative study of hemispherical solar stills with various modifications to obtain modified and inexpensive still models
2021
Attia, Mohammed El Hadi | Kabeel, Abd Elnaby | Abdelgaied, Mohamed | Abdelaziz, Gamal B.
The present study aims to obtain the best modification of the hemispherical solar distillers that achieves the highest productivity with the lower inexpensive. To achieve this goal, this paper dealt with conducting a comparative study, operating performance analysis and an economic study of two different modifications, and comparing them with the reference distiller in order to obtain the best adjustments that achieve the highest productivity at the lowest cost. In the first modification, CuO nanoparticles with three different concentrations (0.1, 0.2, and 0.3%) were added to the basin water, to increase the intensity of absorbed solar energy, improve the thermal properties of basin fluid, and then increase the rate of vapor generation inside the distillation basin. In the second modification, water film glass cooling technology with three different flow rates (1.5, 2, and 2.5 L/h) was utilized to increase the water vapor condensation rate. In this experimental study, three hemispherical distillers were fabricated and tested under the same climate conditions at a 1-cm basin fluid depth, namely, conventional hemispherical solar still (CHSS), hemispherical solar still with glass cover cooling (HSS-C), and hemispherical solar still with CuO-water-based nanofluid (HSS-N). The experimental results presented that the average daily accumulative yield of CHSS is 3.85 L/m²/day, while the daily accumulative yield of HSS-N increases to 5.75, 6.40, and 6.80 L/m²/day with improvement 49.3, 66.2, and 76.6% at volume fraction 0.1, 0.2, and 0.3%, respectively. Also, the daily accumulative yield of HSS-C increases to 4.9, 5.35, and 5.7 L/m²/day with improvements of 27.3, 39, and 48% at water film flow rates of 1.5, 2, and 2.5 L/h, respectively. The cost of distilled water produced from CHSS is 0.0106 $/L, while the utilization of HSS-C (2.5 L/h) and HSS-N (0.3%) reduces the cost of distilled water to 0.0072 and 0.0066 $/L, respectively. Based on accumulative yield and economic analyzes, it is recommended that the modified HSS-N (0.3% volume fraction) be utilized to achieve the highest accumulative yield and the lowest price of the produced distilled water.
Mostrar más [+] Menos [-]Heat transfer study of a new hybrid photovoltaic/thermal direct absorption parabolic solar collector by two-phase Buongiorno model
2021
Tolouei, Iman | Tolouei, Ehsan | Motlagh, Saber Yekani | Mobadersani, Farrokh
Solar energy is one of the cleanest sources of renewable energy that is easily accessible in vast geographical areas. As the efficiency of the common solar collectors is very low and is limited by the absorption properties of working fluid, enhancing the thermal performance of these collectors is one of the major challenges of developing parabolic solar thermal power plants. In recent decades, researches revealed that utilizing nanofluid as a novel working fluid has a dramatic effect on the thermophysical and optical properties of the fluid. In this study, the flow and temperature fields of water/magnetite and water/aluminum nanofluids are evaluated by solving the steady form of governing equations including conservation laws of mass, volume fraction transport equation, momentum equation, energy equation, and radiation transfer equation. Moreover, the two-phase Buongiorno model is utilized and Brownian motion, thermophoresis effects, and magnetophoresis movement are taken into account in the nanofluid simulation. The numerical results demonstrate that increasing nanofluid volume fraction and flow rate can increase the thermal performance of the collector tube. It is found that the thermal efficiencies reach maximum values of 151.03% and 158.58% for water/aluminum and water/magnetite nanofluids, respectively. Furthermore, increasing the volume fraction from 0 to 0.3% leads to rise of 24.41% and 21.36% in the maximum temperature of the collector. The effects of different parameters such as nanoparticle volume fraction, flow rate, and nanoparticle kind on the collector thermal and electrical efficiencies, thermal distribution, and entropy production have been studied.
Mostrar más [+] Menos [-]Effect of nanoparticle on rheological properties of surfactant-based nanofluid for effective carbon utilization: capturing and storage prospects
2021
Kumar, Ravi Shankar | Goswami, Rishiraj | Chaturvedi, Krishna Raghav | Sharma, Tushar
Previous studies have shown insufficient dispersion and thermal stability of nanofluids for high-temperature carbon capture and storage applications. Compared to the other NPs, TiO₂ nanofluids exhibit superior stability due to their high zeta potential. In previous studies, TiO₂ nanofluids have shown superior performance in heat transfer and cooling applications along with importing the stability of other nanofluids like SiO₂ in form of nanocomposites. Therefore, in this study, a nanofluid formulation consisting of titania nanofluid in a base solution of ethylene glycol (EG) with different co-stabilizers such as surfactants was synthesized for better dispersion stability, enhanced electrical, and rheological properties especially for the use in high-temperature industrial applications which include carbon capture and storage along with enhanced oil recovery. The formulated nanofluid was investigated for stability using dynamic light scattering (DLS) study and electrical conductivity. Additionally, the formulated nanofluid was also examined for thermal stability at high temperatures using an electrical conductivity study followed by rheological measurements at 30 and 90 °C. At a high temperature, the shear-thinning behavior of EG was found highly affected by shear rate; however, this deformation was controlled using TiO₂ nanoparticles (NPs). Furthermore, the role of surfactant was also investigated on dispersion stability, electrical conductivity followed by viscosity results, and it was found that the nanofluid is superior in presence of anionic surfactant sodium dodecyl sulfate (SDS) as compared to nonionic surfactant Triton X-100 (TX-100). The inclusion of ionic surfactant provides a charged layer of micelles surrounding the core of a NP and it produced additional surface potential. Consequently, it increases the repulsive force between two adjacent NPs and renders a greater stability to nanofluid while nonionic surfactant allowed monomers to adsorb on the surface of NP via hydrophobic interaction and enhances the short-range interparticle repulsion, to stabilize nanofluid. This makes titania nanofluid suitable for widespread high-temperature applications where conventional nanofluids face limitations. Finally, the application of the synthesized titania nanofluids was explored for the capture and transport of CO₂ where the inclusion of the anionic surfactant was found to increase the CO₂ capturing ability of titania nanofluids by 140–220% (over the conventional nanofluid) while also showing superior retention at both investigated temperatures. Thus, the study promotes the role of novel surfactant-treated titania nanofluids for carbon removal and storage and recommends their applications involving carbonated fluid injection (CFI) to carbon utilization in oilfield applications.
Mostrar más [+] Menos [-]Comparative study of double-slope solar still, hemispherical solar still, and tubular solar still using Al2O3/water film cooling: a numerical study and CO2 mitigation analysis [Erratum: September 2022, v.29(43), p.65370]
2022
Shoeibi, Shahin | Ali Agha Mirjalily, Seyed | Kargarsharifabad, Hadi | Panchal, Hitesh | Dhivagar, Ramasamy
Solar still, as one of the important devices for generating water using renewable energy, has been widely used in arid as well as coastal areas where access to fresh water is limited. This paper uses CFD simulation to compare double-slope solar still, hemispherical solar still, and tubular solar still using nanofluid film cooling. Al₂O₃-water nanofluids with a concentration of 0.1% are used due to facilitate sunlight penetration into the absorber plate inside the solar desalination. It is assumed the flow is steady, laminar, and air is an ideal and incompressible gas. The simple algorithm is considered to calculate the relationship between pressure and velocity and to separate the transfer and pressure interpolation terms from the appropriate upstream designs. Also, the economic, exergoeconomic, and CO₂ mitigation parameters of various solar stills were investigated. The study revealed that the water productivity of double-slope solar desalination using nanofluids film cooling is improved by about 4.8% compared with tubular solar desalination with nanofluid film cooling. Also, the lowest CPL of 0.0362 $/L was obtained in the double-slope solar desalination using nanofluid film cooling. The net CO₂ mitigation of 14.08 tons, 13.72 tons, and 13.44 tons was obtained for double-slope solar desalination, hemispherical solar desalination, and tubular solar desalination, respectively.
Mostrar más [+] Menos [-]Experimental investigation on lowering the environmental hazards and improving the performance patterns of solar flat plate collectors by employing the internal longitudinal fins and nano additives
2020
Munuswamy, Dinesh Babu | Devarajan, Yuvarajan | Babu, M Naresh | Ramalingam, Sathiyamoorthi
The main objective of this study is to lower the greenhouse gases by developing and optimizing a solar flat plate collector. The rifled tube is integrated into the collector to increase the thermal heat transfer thereby improving its performance. Two flat plate collectors, one with in-housed longitudinal fins and another without fins of 0.5 m² collector area, have been intended and fabricated with provisions for K-type thermocouples to examine the temperature variations inside the collector for different working fluids. This current study reveals using CuO and Al₂O₃ nanoparticles in varying weight fractions in incremental order to study the effect of weight fractions on the efficiency of the collector. The simulation was done using computational fluid dynamics both for the finned and without finned tube collectors separately and the outcome of the results for the collector outlet temperatures is compared with the experimental one and results show a valuable outcome for the intended collectors. Initially, the test was conducted with pure distilled water as working fluid and further nanoparticles were opted and doped inside the collector side for varying weight fractions of 0.2% and 0.4% and their results are compared. The experimental results showed an improved heat transfer was pragmatic in the collector side for using nanoparticles. Mixing the nanofluids exhibited superior efficiency on the collector side. The results showed after successful trials of experimentation, doping of CuO nanoparticles by varying weight fractions of 0.2% and 0.4%, augmentation of the collector (unfinned) efficiency is 2.1% and 4.05%, and similarly for finned tube collector, it is 3.02% and 5.5% for same weight fractions. In order to improve the thermal efficiency of collector, CuO is replaced by Al₂O₃ nanoparticles; for dissimilar weight fractions, the efficiency is enhanced nearly by 3.7% and 6.54% for unfinned tube collector, and for the finned tube, the collector is 4.8% and 7.8% respectively, compared with the base working fluid (water). Experimentation of the collectors with finned tube type achieved a superior efficiency compared with that of unfinned tube collectors which is proved to be higher when used for nanofluids to that of the base working fluid water.
Mostrar más [+] Menos [-]