High concentration of fluoride (up to 20.9 mg/L) in groundwater with significant variation (p = 5.9E-128) among samples was reported from Birbhum district, an acknowledged fluoride endemic region in India. The groundwater samples (N = 368) were grouped based on their hydrochemical properties and aquifer geology for hydro-geochemical characterization. Friedman’s test showed p < 0.0001 confidence level which indicates that fluoride concentration among geological groups and water groups are independent. Bland-Altman plot was used to study the inter-relationships among the groups through bias value (∂) and limit of agreement (LoA). Among the geological groups, laterites and granite-gneiss groups exhibited statistically significantly difference in fluoride geochemistry; whereas the younger and older alluvium groups displayed similar characteristics. The fluoride concentration was found to be in the order Lateritic > Granite-gneiss > Older alluvium ≥ Younger alluvium. Dissolution of minerals (such as fluorite, biotite) in laterite sheeted basalt, and granite-gneiss is the main source of groundwater fluoride in the region. Fluoride concentration is also influenced by depth of water table. Hydrochemical study indicated that fluoride concentration was higher in Na–HCO₃ than in Ca–SO₄ and Ca–HCO₃ type of groundwater. The fluoride concentration were positively correlated with Na⁺ and pH and negatively correlated with the Ca²⁺ and Mg²⁺ signifying linkage with halite dissolution and calcite, dolomite precipitation. Geostatistical mapping of WQI through empirical bayesian kriging (EBK) with respect to regional optimal guideline value (0.73 mg/L) classified that groundwater in some parts of the district are unfit for drinking purpose. Health survey (N = 1767) based on Dean’s criteria for dental fluorosis indicated presence of slight to moderate dental hazard. Besides, providing baseline data for management of groundwater quality in the study area, the study demonstrated the applicability of Bland-Altman analysis and empirical bayesian kriging (EBK) in delineation and interpolation of fluoride contaminated region.

Cadmium (Cd), a major environmental contaminant, is closely associated with male reproductive health. Selenium (Se) has been recognized as an effective chemo-protectant against Cd toxicity, but the underlying mechanisms remain unclear. The objective of present study was to illustrate the toxic effect of Cd on testis, and then compare the antagonistic effect among different Se sources on growth performance, testicular damage, ion homeostasis, antioxidative potential, and the expression of selenotranscriptome and biosynthetic related factors in Cd-treated chicken. Male chickens were fed with (Ⅰ) Control group: basal diet; (Ⅱ) Cd group: basal diet with 140 mg/kg CdCl₂; (Ⅲ) YSe + Cd group: basal diet with 140 mg/kg CdCl₂ and 3 mg/kg Yeast-Se; (Ⅳ) NSe + Cd group: basal diet with 140 mg/kg CdCl₂ and 1 mg/kg Nano-Se; (Ⅴ) SSe + Cd group: basal diet with 140 mg/kg CdCl₂ and 3 mg/kg Na₂SeO₃. It was observed that different Se treatments dramatically alleviated Cd-induced testicular developmental disorder, ion homeostasis disorder, hormone secretion disorder and oxidative stress. Simultaneously, Se mitigated Cd-induced testicular toxicity by regulating selenoprotein biosynthetic related factors to promote selenoprotein transcription. Finally, this study indicated that dietary supplementation of Yeast-Se produced an acceptable Se form to protect testis from Cd exposure.

To characterise the mass concentration, size-distribution, and respiratory deposition of selected trace metals (Cr, Mn, Fe, Ni, Cu, Zn, Ba, and Pb) in size-segregated PM₂.₅, a long-term monitoring campaign was undertaken at an urban background site in Como (Northern Italy). 96-h aerosol samples were collected weekly, from May 2015 to March 2016, using a 13-stage low pressure impactor and analysed via laser ablation-inductively coupled plasma-mass spectrometry. Significantly higher levels of trace metals were generally found during the heating season (two to more than four times) compared to the non-heating period at all size ranges, especially for concentrations in PM₀.₁–₁. Distinct distribution profiles characterised the different elements, even though the corresponding heating and non-heating shapes always exhibited similar features, with negligible seasonal shifts in the average mass median aerodynamic diameters. Fe, Ba, and Cu had >70% of their mass in PM₁–₂.₅, whereas Pb, Zn, and Ni showed higher contributions in the accumulation mode (>60%). Finally, broad size-distributions were found for Cr and Mn. The multiple-path particle dosimetry model estimated the overall deposition fractions in human airways varying between 27% (Pb) and 48% (Ba). The greatest deposition variability was always registered in the head region of the respiratory system, with the highest contributions for those metals predominantly accumulated in the PM₂.₅ coarse modes. In contrast, the deposition in the deepest respiratory tract maintained nearly constant proportions over time, becoming notably important for Pb, Ni, and Zn (∼13%) with respect to their total deposition. The comparison with national limits established for Pb and Ni suggested the absence of significant risks for the local population, as expected, with average concentrations two orders of magnitude lower than the corresponding annual limit and objective value. Similar findings were reported for all the other metals, for which the estimated hazard quotients were always well <1.

Persistent organic pollutants (POPs) are believed to alter metabolic homeostasis during fetal development, leading to childhood obesity. However, limited studies have explored how fetal chemical exposures relate to birth and infant weight outcomes in low-income Hispanic families at the highest risk of obesity. Therefore, we sought to determine associations between neonatal POPs exposure measured in newborn dried blood spots (DBS) and prenatal diet quality, birth weight, and overweight status at 18 months old. We conducted a case-control study nested within the Starting Early Program randomized controlled trial comparing POPs concentrations in infants with healthy weight (n = 46) and overweight status (n = 52) at age 18 months. Three categories of POPs, organochlorine pesticides (OCPs), polybrominated diphenyl ethers (PBDEs) and perfluoroalkyl substances (PFASs) were measured in archived newborn DBS. We assessed correlations between prenatal diet quality and neonatal POPs concentrations. Multivariable regression analyses examined associations between POPs (dichotomized at the mean) and birth weight z-score and weight status at 18 months, controlling for confounders. Seven of eight chemicals had detectable levels in greater than 94% of the sample. Higher protein, sodium and refined grain intake during pregnancy were correlated with lower POPs in newborn DBS. We found that high concentrations of perfluorooctanesulfonate (unstandardized coefficient [B]: −0.62, 95% confidence interval [CI]: −0.96 to −0.29) and perfluorohexanesulfate (B: −0.65, 95% CI: −0.99 to −0.31) were related to lower birth weight z-scores compared to those with low concentrations. We did not find associations between PBDEs, OCPs, and the other PFASs with birth weight z-scores, or between any POPs and weight status at 18 months. In conclusion, two PFASs were associated with lower birth weight, an important indicator of child health and growth, although direct associations with infant overweight status were not found. Whether neonatal POPs exposures contribute to economic and ethnic disparities in early obesity remains unclear.

Uncertainty assessment of parameters associated with non-point source pollution mechanism modeling are crucial for improving the effectiveness of pollution controlling. In this study, an approach based on Bayesian inference and integrated Markov chain Monte Carlo and multilevel factorial analysis has been developed, and it can not only apply straightforward Bayesian inference to assess parameter uncertainties, but also quantitatively investigate the main and interactive effects of multiple parameters on the model response variables by measuring the specific variations of model outputs. Its applicability and advantages are presented through the application of the Soil and Water Assessment Tool to Shitoukoumen Reservoir Catchment in northeast China. This study investigated the uncertainties of a set of sensitive parameters and their multilevel effects on model response variables, including average annual runoff (AAR), average annual sediment (AAS) and average annual total nitrogen (AAN). Results revealed that (i) soil conservation service runoff curve number for moisture condition II (CN2) had a positive effect on all response variables; (ii) available water capacity of the soil layer (SOL_AWC) had a negative effect on all response variables; (iii) the universal soil loss equation support practice (USLE_P) had a positive effect on AAS and AAN, and little effect on AAR; while the nitrate percolation coefficient (NPERCO) had a positive effect on AAN, and little effect on AAS and AAR; and (iv) the interactions amongst parameters had obvious interdependent effects on the model response variables, for example, the interaction between CN2 and SOL_AWC had a major impact on AAR. The above findings can improve the simulating and predicting capabilities of non-point source pollution mechanism model. Overall, this study highlights that the proposed approach represents a promising solution for uncertainty assessment of model parameters in non-point source pollution mechanism modeling.

Fungicides, usually refer to the chemical agents that can effectively control or kill the pathogenic microorganisms. Here, we revealed the effects of three different fungicides, imazalil (IMZ), chlorothalonil (CTL) and carbendazim (CBZ), which are typical broad-spectrum fungicides that are detected at high levels in the natural environment, on heterogeneous human epithelial colorectal cells (Caco-2 cells). All three fungicides had the potential to induce different degrees of toxicity, cause apoptosis, reactive oxygen species (ROS) and even change the cell cycle in the cells. The half maximal inhibitory concentration (IC50) of CTL is the lowest among these three fungicides, suggesting that it may have the highest exposure risk, followed by IMZ, and CBZ. The results of the real-time PCR, Western blotting, and mitochondrial membrane potential (MMP) assays and the activities of key enzymes suggested that CTL induced apoptosis in Caco-2 cells via a mitochondrial-dependent pathway, as indicated by the upregulation of the expression of the apoptotic p53 and bax genes, the increase of the apoptosis marker cytochrome-c, the decrease of mRNA level of bcl-2 gene, and the decrease in the MMP. Exposure to two other fungicides also upregulated the transcriptional level of bax and the expression of cytochrome-c, but the mRNA level of bcl-2 was increased (IMZ) or unchanged (CBZ), suggesting that other pathways may be involved in the induction of cellular apoptosis by these two fungicides. In addition, all three of the fungicides could induce oxidative stress in Caco-2 cells. Our data showed that the three different kinds of fungicides all caused toxic effects in Caco-2 cells through various pathways.

Dibutyl phthalate (DBP) is widely used as plasticizer and has been detected in the environment, posing a threat to animal health. However, the effects of DBP on agricultural microbiomes are not known. In this study, DBP levels in black soil were evaluated, and the impact of DBP contamination on the uptake and metabolism of sugars in microbes was assessed by glucose absorption tests, metaproteomics, metabolomics, enzyme activity assays and computational simulation analysis. The results indicated that DBP contamination accelerated glucose consumption and upregulated the expression of porins and periplasmic monosaccharide ATP-binding cassette (ABC) transporter solute-binding proteins (SBPs). DBP and its metabolic intermediates (carboxymuconate and butanol) may form a stable complex with sugar transporters and enhance the rigidity and stability of these proteins. Sugar metabolism resulting in the generation of ATP and reducing agent (NADPH), as well as the expression of some key enzymes (dehydrogenases) were also upregulated by DBP treatment. Moreover, a diverse bacterial community appears to utilize sugar, suggesting that there are widespread effects of DBP contamination on soil microbial ecosystems. The results of this study provide a theoretical basis for investigating the toxicological effects of DBP on microbes in black soil.

Microplastics (MPs) pollution in the marine environment has attracted considerable global attention. However, the colonization of microorganisms on mariculture-derived MPs and their effects on mariculture remain poorly understood. In this study, the MPs (fishing nets, foams and floats) and a natural substrate, within size ranges (1–4 mm), were then incubated for 21 days in Sungo Bay (China), and the composition and diversity of bacterial communities attached on all substrates were investigated. Results showed that bacterial communities on MPs mainly originated from their surrounding seawater and sediment, with an average contribution on total MPs adherent population of 47.91% and 37.33%, respectively. Principle coordinate analysis showed that community similarity between MPs and surrounding seawater decreased with exposure time. In addition, lower average bacterial community diversity and higher relative abundances of bacteria from the genera Vibrio, Pseudoalteromonas and Alteromonas on MPs than those in their surrounding seawater and sediments indicated that MPs might enrich potential pathogens and bacteria related with carbohydrate metabolism. They are responsible for the significant differences in KEGG Orthology pathways (infectious disease and carbohydrate metabolism) between MPs and seawater. The KO pathway (Infectious Diseases) associated with MPs was also significantly higher than those with feathers in the nearshore area. MPs might be vectors for enrichment of potentially pathogenic Vibrio, and enhance the ecological risk of MPs to mariculture industry.

Cadmium (Cd) exposure poses a serious environmental problem due to the metal’s bioaccumulation and difficult to eliminate from body. Understanding the mechanisms of Cd detoxification and resistance can provide insights into methods to protect against the damaging effects of the heavy metal. In the present study, we found that heat shock (HS) pretreatment increased Cd resistance of the nematode Caenorhabditis elegans by reducing the bagging phenotype and protecting the integrity of the intestinal barrier. HS pretreatment increased the expression of heat shock protein-16.2 (HSP-16.2) prior to Cd exposure, and HS-induced Cd resistance was absent in worms with hsp-16.2 loss-of-function mutation. Worm strain with daf-2(e1370) mutation presented enhanced HS-induced Cd resistance, which was eliminated in worm strains of daf-16(mu86) and hsf-1(sy441). HS pretreatment increased DAF-16 nuclear localization and HSF-1 granule formation prior to Cd exposure. DAF-16 and HSF-1 was essential in reducing bagging formation and protecting the integrity of intestinal barrier after HS pretreatment. In conclusion, the present study demonstrated that HS-induced Cd resistance in C. elegans is regulated by the DAF-16/FOXO and HSF-1 pathways through regulation of HSP-16.2 expression.

Achieving large pore size, high catalytic performance with stable structure is critical for metal–organic frameworks (MOFs) to have more hopeful prospects in catalytic applications. Herein, we had reported a method to synthesize highly reactive yet stable defective iron-based Metal organic frameworks by using different monocarboxylic acids with varying lengths as a modulator. The physical−chemical characterization illustrating that modulators could improve the crystallinity, enlarge pore size and enhance catalytic performance and octanoic acid (OA) was screened to be the suitable choice. The catalytic performance of catalysts was detected through persulfate (PS) activation for degrading Tetrabromobisphenol A (TBBPA). The study demonstrated that the highest degradation efficiency for 0.018 mmol L−1 TBBPA was that 97.79% in the conditions of the 1.0 g L−1 Fe(BDC)(DMF,F)-OA-30 dosage and TBBPA:PS = 200:1. In addition, there was observed that no obvious change of the crystal structure, little the leachable iron concentration in the solutions and no significant loss of catalytic activities of Fe(BDC)(DMF,F)-OA-30 after 5th cycles. The iron valence state of Fe(BDC)(DMF,F)-OA-30 before and after degradation and electrochemical properties reveal that the partial substitution of organic ligands by octanoic acid, when removing OA and forming defects by heat and vacuum treatment to generate coordinatively unsaturated metal sites and accelerate the original transmission of electronic, leading to enhance the activity of persulfate activation for efficient removal TBBPA.