Background, aim, and scope Chlorinated volatile organic compounds (CVOCs), widely used in industry as solvents and chemical intermediates in the production of synthetic resins, plastics, and pharmaceuticals, are highly toxic to the environment and public health. Various studies reported that Fenton's oxidation could degrade a variety of chlorinated VOCs in aqueous solutions. In acidic conditions, ferrous ion catalyzes the decomposition of H₂O₂ to form a powerful •OH radical. In this study, wastewater from wash of ion-exchange resin containing typical CVOC, 1,2-dichloroethane, was treated using Fenton's oxidation. To reduce environmental load and processing costs of wastewater, Fenton process as a simple and efficient treatment method was applied to degrade 1,2-dichloroethane of wash water. Materials and methods The water samples were collected from three different washing stages of ion-exchange resin. The degradation of 1,2-dichloroethane and total organic carbon (TOC) of wash water of ion-exchange resin by Fenton process was studied with response surface method (RSM). Design of the experiments was conducted by central composite face, and factors included in three models were Fe²⁺ and H₂O₂ doses and treatment time. Relevant quadratic and interaction terms of factors were investigated. Results According to ANOVA, the model predicts well 1,2-dichloroethane reduction of all water samples and TOC reduction of samples 2 and 3. The Fe²⁺ and H₂O₂ doses used in the present study were most suitable when 1,2-dichloroethane concentration of the wash water is about 120 mg L⁻¹. In that case, Fenton's oxidation reduced 1,2-dichloroethane and TOC up to 100% and 87%, respectively, according to the RSM model. With 90-min reaction time and H₂O₂ dose of 1,200 mg L⁻¹, the required Fe²⁺ doses for 1,2-dichloroethane and TOC were 300 and 900 mg L⁻¹, respectively. The optimal H₂O₂/Fe²⁺ stoichiometric molar ratio was between 4-6. Then, concentration of Fe²⁺ was low enough and the amount of residual sludge can thus be reduced. It seems that most of TOC and part of 1,2-dichloroethane were removed by coagulation. Discussion Up to a certain extent, increase of Fe²⁺ and H₂O₂ doses improved the removal of 1,2-dichloroethane and TOC. High Fe²⁺ doses increased the formation of ferric-based sludge, and excessive H₂O₂ doses in sample 2 decreased the degradation of 1,2-dichloroethane. Excess amount of hydrogen peroxide may scavenge hydroxyl radicals, thus leading to loss of oxidative power. Also, the residual hydrogen peroxide of different samples increased with increasing H₂O₂ dose and H₂O₂/Fe²⁺ molar ratio and decreasing treatment time probably also due to scavenging reactions. Due to the saturated nature of 1,2-dichloroethane, the oxidation mechanism involves hydrogen abstraction before addition of hydroxyl radical, thus leading to lower rate constants than for direct hydroxyl radical attack, which for one increases the treatment time. Conclusions Complete removal of 1,2-dichloroethane was attained with initial concentration <120 mg L⁻¹. Also, TOC degraded effectively. Wash water with higher concentration of 1,2-dichloroethane requires longer treatment times and higher concentrations of Fe²⁺ and H₂O₂ for sufficient 1,2-dichloroethane removal. Recommendations and perspectives Due to the results achieved in this study, Fenton's oxidation could be recommended to be used for organic destruction of wash water of ion-exchange resin. Residual sludge, the main disadvantage in Fenton process, can be reduced by optimizing the ferrous dose or by using heterogeneous treatment where most of the reusable iron remains in the solid phase.

Background, aim, and scope The occurrence and fate of pharmaceuticals in the aquatic environment is recognized as one of the emerging issues in environmental chemistry and as a matter of public concern. Existing data tend to focus on the concentrations of pharmaceuticals in the aqueous phase, with limited studies on their concentrations in particulate phase such as sediments. Furthermore, current water quality monitoring does not differentiate between soluble and colloidal phases in water samples, hindering our understanding of the bioavailability and bioaccumulation of pharmaceuticals in aquatic organisms. In this study, an investigation was conducted into the concentrations and phase association (soluble, colloidal, suspended particulate matter or SPM) of selected pharmaceuticals (propranolol, sulfamethoxazole, meberverine, thioridazine, carbamazepine, tamoxifen, indomethacine, diclofenac, and meclofenamic acid) in river water, effluents from sewage treatment works (STW), and groundwater in the UK. Materials and methods The occurrence and phase association of selected pharmaceuticals propranolol, sulfamethoxazole, meberverine, thioridazine, carbamazepine, tamoxifen, indomethacine, diclofenac, and meclofenamic acid in contrasting aquatic environments (river, sewage effluent, and groundwater) were studied. Colloids were isolated by cross-flow ultrafiltration (CFUF). Water samples were extracted by solid-phase extraction (SPE), while SPM was extracted by microwave. All sample extracts were analyzed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) in the multiple reaction monitoring. Results and discussion Five compounds propranolol, sulfamethoxazole, carbamazepine, indomethacine, and diclofenac were detected in all samples, with carbamazepine showing the highest concentrations in all phases. The highest concentrations of these compounds were detected in STW effluents, confirming STW as a key source of these compounds in the aquatic environments. The calculation of partition coefficients of pharmaceuticals between SPM and filtrate (observed partition coefficients, [graphic removed] , [graphic removed] ), between SPM and soluble phase (intrinsic partition coefficients, [graphic removed] , [graphic removed] ), and between colloids and soluble phase (K coc) showed that intrinsic partition coefficients [graphic removed] are between 25% and 96%, and between 18% and 82% higher than relevant observed partition coefficients values, and are much less variable. Secondly, K coc values are 3-4 orders of magnitude greater than [graphic removed] values, indicating that aquatic colloids are substantially more powerful sorbents for accumulating pharmaceuticals than sediments. Furthermore, mass balance calculations of pharmaceutical concentrations demonstrate that between 23% and 70% of propranolol, 17-62% of sulfamethoxazole, 7-58% of carbamazepine, 19-84% of indomethacine, and 9-74% of diclofenac are present in the colloidal phase. Conclusions The results provide direct evidence that sorption to colloids provides an important sink for the pharmaceuticals in the aquatic environment. Such strong pharmaceutical/colloid interactions may provide a long-term storage of pharmaceuticals, hence, increasing their persistence while reducing their bioavailability in the environment. Recommendations and perspectives Pharmaceutical compounds have been detected not only in the aqueous phase but also in suspended particles; it is important, therefore, to have a holistic approach in future environmental fate investigation of pharmaceuticals. For example, more research is needed to assess the storage and long-term record of pharmaceutical residues in aquatic sediments by which benthic organisms will be most affected. Aquatic colloids have been shown to account for the accumulation of major fractions of total pharmaceutical concentrations in the aquatic environment, demonstrating unequivocally the importance of aquatic colloids as a sink for such residues in the aquatic systems. As aquatic colloids are abundant, ubiquitous, and highly powerful sorbents, they are expected to influence the bioavailability and bioaccumulation of such chemicals by aquatic organisms. It is therefore critical for colloids to be incorporated into water quality models for prediction and risk assessment purposes.

Background, aim, and scope The chemical substance 2,4,7,9-tetramethyl-5-decyne-4,7-diol (TMDD) is a non-ionic surfactant used as an industrial defoaming agent and in various other applications. Its commercial name is Surynol 104® and the related ethoxylates are also available as Surfynol® 420, 440, 465 and 485 which are characterized by different grades of ethoxylation of TMDD at both hydroxyl functional groups. TMDD and its ethoxylates offer several advantages in waterborne industrial applications in coatings, inks, adhesives as well as in paper industries. TMDD and its ethoxylates can be expected to reach the aquatic environment due its widespread use and its physico-chemical properties. TMDD has previously been detected in several rivers of Germany with concentrations up to 2.5 µg/L. In the United States, TMDD was also detected in drinking water. However, detailed studies about its presence and distribution in the aquatic environment have not been carried out so far. The aim of the present study was the analysis of the spatial and temporal concentration variations of TMDD in the river Rhine at the Rheingütestation Worms (443.3 km). Moreover, the transported load in the Rhine was investigated during two entire days and 7 weeks between November 2007 and January 2008. Materials and methods The sampling was carried out at three different sampling points across the river. Sampling point MWL1 is located in the left part of the river, MWL2 in the middle part, and MWL4 in the right part. One more sampling site (MWL3) was run by the monitoring station until the end of 2006, but was put out of service due to financial constrains. The water at the left side of the river Rhine (MWL1) is influenced by sewage from a big chemical plant in Ludwigshafen and by the sewage water from this city. The water at the right side of the river Rhine (MWL4) is largely composed of the water inflow from river Neckar, discharging into Rhine 14.9 km upstream from the sampling point and of communal and industrial wastewater from the city Mannheim. The water from the middle of the river (MWL2) is largely composed of water from the upper Rhine. Water samples were collected in 1-L bottles by an automatic sampler. The water samples were concentrated by use of solid-phase extraction (SPE) using Bond Elut PPL cartridges and quantified by use of gas chromatography-mass spectrometry (GC-MS). The quantification was carried out with the internal standard method. Based on these results, concentration variations were determined for the day profiles and week profiles. The total number of analyzed samples was 219. Results The results of this study provide information on the temporal concentration variability of TMDD in river Rhine in a cross section at one particular sampling point (443.3 km). TMDD was detected in all analyzed water samples at high concentrations. The mean concentrations during the 2 days were 314 ng/L in MWL1, 246 ng/L in MWL2, and 286 ng/L in MWL4. The variation of concentrations was low in the day profiles. In the week profiles, a trend of increasing TMDD concentrations was detected particularly in January 2008, when TMDD concentrations reached values up to 1,330 ng/L in MWL1. The mean TMDD concentrations during the week profiles were 540 ng/L in MWL1, 484 ng/L in MWL2, and 576 ng/L in MWL4. The loads of TMDD were also determined and revealed to be comparable in all three sections of the river. The chemical plant located at the left side of the Rhine is not contributing additional TMDD to the river. The load of TMDD has been determined to be 62.8 kg/d on average during the entire period. By extrapolation of data obtained from seven week profiles the annual load was calculated to 23 t/a. Discussion The permanent high TMDD concentrations during the investigation period indicate an almost constant discharge of TMDD into the river. This observation argues for effluents of municipal wastewater treatment plants as the most likely source of TMDD in the river. Another possible source might be the degradation of ethoxylates of TMDD (Surfynol® series 400), in the WWTPs under formation of TMDD followed by discharge into the river. TMDD has to be considered as a high-production-volume (HPV) chemical based on the high concentrations found in this study. In the United States, TMDD is already in the list of HPV chemicals from the Environmental Protection Agency (EPA). However, the amount of TMDD production in Europe is unknown so far and also the biodegradation rates of TMDD in WWTPs have not been investigated. Conclusions TMDD was found in high concentrations during the entire sampling period in the Rhine river at the three sampling points. During the sampling period, TMDD concentrations remained constant in each part of the river. These results show that TMDD is uniformly distributed in the water collected at three sampling points located across the river. ‘Waves' of exceptionally high concentrations of TMDD could not be detected during the sampling period. These results indicate that the effluents of WWTPs have to be considered as the most important sources of TMDD in river Rhine. Recommendations and perspectives Based also on the occurrence of TMDD in different surface waters of Germany with concentrations up to 2,500 ng/L and its presence in drinking water in the USA, more detailed investigations regarding its sources and distribution in the aquatic environment are required. Moreover, the knowledge with respect to its ecotoxicity and its biodegradation pathway is scarce and has to be gained in more detail. Further research is necessary to investigate the rate of elimination of TMDD in municipal and industrial wastewater treatment plants in order to clarify the degradation rate of TMDD and to determine to which extent effluents of WWTPs contribute to the input of TMDD into surface waters. Supplementary studies are needed to clarify whether the ethoxylates of TMDD (known as Surfynol 400® series) are hydrolyzed in the aquatic environment resulting in formation of TMDD similar to the well known cleavage of nonylphenol ethoxylates into nonylphenols. The stability of TMDD under anaerobic conditions in groundwater is also unknown and should be studied.

Background, aim, and scope High mountain soils constitute a long-term cumulative record of atmospherically deposited trace elements from both natural and anthropogenic sources. The main aims of this study were to determine the level of major and trace metals (Al, Ti, Mn, Fe, and Zr) of lithologic origin and airborne contaminating trace elements (Ni, Cu, Zn, As, Cd, and Pb) in soils in the Central Pyrenees as an indication of background contamination over SW Europe, to establish whether there is a spatial pattern of accumulation of trace elements in soils as a function of altitude, and to examine whether altitude-related physicochemical properties of soils affect the accumulation of major metals and trace elements. Methods Major metals and trace elements were measured in “top” (i.e., first 10 cm) and “bottom” (i.e., below 10 cm) soil samples along an altitudinal transect (1,520-2,880 m a.s.l.) in the Central Pyrenees. Total concentrations were determined by X-ray fluorescense spectrometry. Total major metal concentrations were analysed by conventional X-ray fluorescence spectrometry (XRF) with a Siemens SRS 303 instrument. Total trace element concentrations were determined with an energy-dispersive multielement miniprobe XRF analyser. Acid-extractable concentrations were measured by inductively coupled plasma after previous extraction with nitric acid and hydrogen peroxide in closed beakers. Acid-extractable major metal concentrations were measured by inductively coupled plasma (ICP)-Optic Emission Spectrometry with a Perkin Elmer 3200 RL Instrument. Acid-extractable trace element concentrations were determined by ICP-Mass Spectrometry with a Perkin Elmer ELAN 6000. Results Trace element concentration ranges were (in mg kg⁻¹, inventories in g m⁻² between parenthesis) <2-58 (0.5-6.6) for Ni, 6-30 (0.2-3.4) for Cu, 38-236 (1.6-32.4) for Zn, 6-209 (0.2-12.8) for As, 0.02-0.64 (<0.04) for Cd, and 28-94 (0.6-13.0) for Pb. These concentrations were, in general, comparable to those recorded in soils from other European mountainous areas and were in many cases above the threshold recommended for ecosystem protection by regional and European environmental authorities. The highest concentrations were found at lower altitudes, indicating an effect of local contamination up to ∼2,300 m a.s.l. Only above this altitude can trace elements in soils be considered representative of a background, long-range atmospheric contamination. Conclusions None of the storage capacity properties of soils examined were determinant of the differences in elemental concentrations along the altitudinal transect. At the upper altitude range, Ni, Cu, and Pb showed a approximately two- to fivefold increase over the average concentration of the local dominant lithology, reflecting the regional and global background of atmospheric contamination in the area.

Background, aim, and scope Solid surfaces in contact with water have been found to be biofouled due to the attachment of various organisms. For better understanding of the biofilm formation, the important initial stage of bacterial attachment was investigated with Pseudomonas aeruginosa PAO1 as a model microorganism. Effects of the biosurfactant rhamnolipids and the shear conditions were particularly examined. Materials and methods A highly reproducible procedure was employed. The procedure involved monitoring and counting the number of attached cells on glass walls of the flow chambers, through which a PAO1 suspension was circulated and, subsequently, a saline solution was passed for washing. The experiments were made under different circulation rates (exerting different shear on the bacteria) and rhamnolipid concentrations. Results and discussions Reproducibility of the procedure was confirmed. The velocity profiles near the flow chamber wall were determined. Rhamnolipids, even at a very low concentration of 13 mg/l, were found to deter the bacterial attachment substantially. Prewashing the cells with a 100 mg/l rhamnolipid solution, however, did not affect the attachment significantly. As for the effect of shear, the PAO1 attachment showed an increasing-then-decreasing trend in the range investigated, i.e., 1.0 to 26 mN/m² shear stresses at the chamber wall. The diffusion-limited transport of cells to the chamber wall might have contributed to, but could not fully explain, the increasing attachment observed in the very low shear range (up to 3.5-5.0 mN/m²). Conclusions As compared to static systems, the flow chamber systems significantly improved the reproducibility of initial attachment results. Flow chamber systems were more suitable for experimental investigations of bacterial attachment to surfaces. Rhamnolipids were found to be potent antifoulants for PAO1 attachment on glass. The initial cell attachment increased with increasing shear at the very low shear range (up to 3.5-5.0 mN/m²), but the attachment could be minimized with further increase of the shear.

Background, aim and scope The applicability of the Whole Effluent Assessment concept for the proof of compliance with the “best available techniques” has been analysed with paper mill wastewater from Germany by considering its persistency (P), potentially bio-accumulative substances (B) and toxicity (T). Materials and methods Twenty wastewater samples from 13 paper mills using different types of cellulose fibres as raw materials have been tested in DIN or ISO standardised bioassays: the algae, daphnia, luminescent bacteria, duckweed (Lemna), fish-egg and umu tests with lowest ineffective dilution (LID) as test result. The potentially bio-accumulative substances (PBS) were determined by solid-phase microextraction and referred to the reference compound 2,3-dimethylnaphthalene. Usually, a primary chemical-physical treatment of the wastewater was followed by a single or multi-stage biological treatment. One indirectly discharged wastewater sample was pre-treated biologically in the Zahn-Wellens test before determining its ecotoxicity. Results No toxicity or genotoxicity at all was detected in the acute daphnia and fish egg as well as the umu assay. In the luminescent bacteria test, moderate toxicity (up to LIDlb = 6) was observed. Wastewater of four paper mills demonstrated elevated or high algae toxicity (up to LIDA = 128), which was in line with the results of the Lemna test, which mostly was less sensitive than the algae test (up to LIDDW = 8). One indirectly discharged wastewater sample was biodegraded in the Zahn-Wellens test by 96% and was not toxic after this treatment. Low levels of PBS have been detected (median 3.27 mmol L⁻¹). The colouration of the wastewater samples in the visible band did not correlate with algae toxicity and thus is not considered as its primary origin. Further analysis with a partial wastewater stream from thermomechanically produced groundwood pulp (TMP) revealed no algae or luminescent bacteria toxicity after pre-treatment of the sample in the Zahn-Wellens test (chemical oxygen demand elimination 85% in 7 days). Thus, the algae toxicity of the respective paper mill cannot be explained with the TMP partial stream; presumably other raw materials such as biocides might be the source of algae toxicity. Discussion Comparative data from wastewater surveillance of authorities confirmed the range of ecotoxicity observed in the study. Wastewater from paper mills generally has no or a moderate ecotoxicity (median LID 1 and 2) while the maximum LID values, especially for the algae and daphnia tests, are considerably elevated (LIDA up to 128, LIDD up to 48). Conclusions Wastewater from paper mills generally is low to moderately ecotoxic to aquatic organisms in acute toxicity tests. Some samples show effects in the chronic algae growth inhibition test which cannot be explained exclusively with colouration of the samples. The origin of elevated algae ecotoxicity could not be determined. In the algae test, often flat dose-response relationships and growth promotion at higher dilution factors have been observed, indicating that several effects are overlapping. Recommendations and perspectives At least one bioassay should be included in routine wastewater control of paper mills because the paper manufacturing industry is among the most water consuming. Although the algae test was the most sensitive test, it might not be the most appropriate test because of the complex relationship of colouration and inhibition and the smooth dose-effect relationship or even promotion of algae growth often observed. The Lemna test would be a suitable method which also detects inhibitors of photosynthesis and is not disturbed by wastewater colouration.

Objective In this paper, results regarding the leaching of trace elements out of mineral building materials under irrigation are presented. Results The leaching in the irrigation test is compared with the leaching under constant water exposure to determine the relevance of the irrigation scenario for the assessment of the environmental compatibility of mineral building materials.

Background, aim and scope The production of alumina involves its extraction from bauxite ore using sodium hydroxide under high temperature and pressure. This process yields a large amount of residue wastes, which are difficult to revegetate due to their inherent hostile properties—high alkalinity and sodicity, poor water retention and low nutrient availability. Although phosphorus (P) is a key element limiting successful ecosystem restoration, little information is available on the availability and dynamics of P in rehabilitated bauxite-processing residue sand (BRS). The major aim of this experiment was to quantify P availability and behaviour as affected by pH, source of BRS and di-ammonium phosphate (DAP) application rate. Materials and methods This incubation experiment was undertaken using three sources of BRS, three DAP application rates (low, without addition of DAP; medium, 15.07 mg P and 13.63 mg N of DAP per jar, 100 g BRS; and high, 30.15 mg P and 27.26 mg N per jar, 100 g BRS), and four BRS pH treatments (4, 7, 9 and 11 (original)). The moisture content was adjusted to 55% water holding capacity and each BRS sample was incubated at 25°C for a period of 119 days. After this period, Colwell P and 0.1 M H₂SO₄ extractable P in BRS were determined. In addition, P sequential fractionation was carried out and the concentration of P in each pool was measured. Results and discussion A significant proportion (37% recovered in Colwell P and 48% in 0.1 M H₂SO₄ extraction) of P added as DAP in BRS are available for plant use. The pH did not significantly affect 0.1 M H₂SO₄ extractable P, while concentrations of Colwell P in the higher initial pH treatments (pH 7, 9 and 11) were greater than in the pH 4 treatments. The labile fractions (sum of NH₄Cl (AP), bicarbonate and first sodium hydroxide extractable P (N(I)P)) consisted of 58-64% and 70-72% of total P in the medium and high DAP rate treatments, respectively. This indicates that most P added as DAP remained labile or moderately labile in BRS, either in solution, or in adsorbed forms on the surface of more crystalline P compounds, sesquioxides and carbonate, or associated with amorphous and some crystalline Al and Fe hydrous oxides. In addition, differences in the hydrochloric acid extractable P and the residual-P fractions among the treatments with and without DAP addition were relative small comparing with other P pools (e.g., NaOH extractable P pools), further indicating the limited capacity of BRS for fixing P added in Ca-P and other most recalcitrant forms. Conclusions P availability in the original BRS without addition of DAP was very low, mostly in recalcitrant form. It has been clearly demonstrated that significant proportions of P added as DAP could remain labile or moderately labile for plant use during the rehabilitation of bauxite-processing residue disposal areas. There was limited capacity of BRS for fixing P in more recalcitrant forms (e.g., Ca-P and residual-P). Concentrations of most P pools in BRS increased with the DAP application rate. The impact of the pH treatment on P availability varied with the type of P pools and the DAP rate. Recommendation and perspectives It is recommended that the development of appropriate techniques for more accurate estimation of P availability in BRS and the quantification of the potential leaching loss of P in BRS are needed for the accurate understanding of P availability and dynamics in BRS. In addition, application of organic matters (e.g., biosolids and biochar, etc.) to BRS may be considered for improving P availability and buffering capacity.

PURPOSE: Chlor-alkali plants are one of the most important point sources of mercury to aquatic environment. The problem of Hg contamination has been studied in a region, Rm Valcea (Romania), impacted by the wastewater discharge of a chlor-alkali plant. The purpose of the present study is to evaluate the current status of mercury pollution in the Babeni reservoir (Olt River) and the exposure of local population via fish consumption to mercury originating from the chlor-alkali plant. METHODS: Sediments were collected from Valcea, Govora and Babeni reservoirs. Grain size distribution, organic content and total mercury (THg) concentrations were analysed in sediments. Fish were purchased from local anglers, and the scalp hair was collected from volunteers. THg in sediment, fish and hair samples was determined using an atomic absorption spectrophotometer for Hg determination. Monomethylmercury (MMHg) was analysed in the muscle and liver tissues by species-specific isotope dilution and capillary gas chromatography hyphenated to inductively coupled plasma mass spectrometer. RESULTS: High mercury concentrations were found in the sediments and in fish from Babeni reservoir, with a median of 2.1 mg/kg (IQR = 3.2) in sediments and a mean value of 1.8 ± 0.8 mg/kg_ww in fish muscle. MMHg concentrations in fish were well above the WHO guidelines for fish consumption. Local population consuming fish from the Babeni reservoir had THg concentrations in hair significantly higher than those consuming fish from upstream reservoirs and/or from the shops and reached a median value of 2.5 mg/kg (IQR = 3.6). CONCLUSIONS: The remnant pollution in the fish of this reservoir, and probably many other lakes and reservoirs receiving Hg polluted wastewater, represents a considerable health risk for the local fish consumers.

Purpose Experiments were conducted to examine the effects of mercury (Hg) on soil nitrification activities and the microbial communities of ammonia-oxidizing bacteria (AOB) and ammonia-oxidizing archaea (AOA). Methods The soil samples spiked with different Hg concentrations were incubated for a period of 1, 2, 4, and 8 weeks in triplicate and the potential nitrification rate (PNR) of the samples was determined. The abundance of AOB and AOA was measured after an 8-week incubation by real-time polymerase chain reaction (PCR) assay of the amoA genes, while the community compositions by cloning and sequencing approaches. Results The soil PNR differed with different incubation periods. It tended to decrease with increasing soil Hg concentrations at week 1, basing on which the half-maximal effective concentration (EC50) was 1.59 mg kg⁻¹. There was no significant difference in the abundance of AOB or AOA among the treatments. The AOB community was dominated by Nitrosospira-like sequences and more than 70% of the obtained clones were affiliated with the cluster 3a.2. The percentage of cluster 3a.1 in AOB community appeared to a consistent trend of decreasing with ascending soil Hg concentrations. While all the AOA sequences in the clone libraries were grouped into cluster S (soil and sediment origin). Conclusions This study revealed that Hg could inhibit soil potential nitrification and the extent varied with incubation periods. Soil Hg pollution changed the composition of soil AOB to some extent. These findings will be helpful to recognize the effects of Hg on the activity and community composition of soil ammonia oxidizers.