Constructed wetlands integrated with microbial fuel cells (MFC-CWs) have been recently developed and tested for removing antibiotics. However, the effects of carbon source availability, electron transfer flux and cathode conditions on antibiotics removal in MFC-CWs through co-metabolism remained unclear. In this study, four experiments were conducted in MFC-CW microcosms to investigate the influence of carbon source species and concentrations, external resistance and aeration duration on sulfamethoxazole (SMX) and tetracycline (TC) removal and bioelectricity generation performance. MFC-CWs supplied with glucose as carbon source outperformed other carbon sources, and moderate influent glucose concentration (200 mg L⁻¹) resulted in the best removal of both SMX and TC. Highest removal percentages of SMX (99.4%) and TC (97.8%) were obtained in MFC-CWs with the external resistance of 700 Ω compared to other external resistance treatments. SMX and TC removal percentages in MFC-CWs were improved by 4.98% and 4.34%, respectively, by increasing the aeration duration to 12 h compared to no aeration. For bioelectricity generation performance, glucose outperformed sodium acetate, sucrose and starch, with the highest voltages of 386 ± 20 mV, maximum power density (MPD) of 123.43 mW m⁻³, and coulombic efficiency (CE) of 0.273%. Increasing carbon source concentrations from 100 to 400 mg L⁻¹, significantly (p < 0.05) increased the voltage and MPD, but decreased the internal resistance and CE. The highest MPD was obtained when the external resistance (700 Ω) was close to the internal resistance (600.11 Ω). Aeration not only improved the voltage and MPD, but also reduced the internal resistance. This study demonstrates that carbon source species and concentrations, external resistances and aeration duration, all play vital roles in regulating SMX and TC removal in MFC-CWs.

The insufficient removal of pollutants and bioelectricity production have become a bottleneck for high-concentration saline wastewater treatment through microbial fuel cell (MFC) technology. Herein, a novel supercapacitor MFC (SC-MFC) was constructed with carbon nanofibers composite electrodes to investigate pollutant removal ability, power generation, and electrochemical properties using real landfill leachate. The possible extracellular electron transfer and nitrogen element conversion pathways in the bioanode were also analyzed. Results showed that the SC-MFC had higher pollutant removal rates (COD: 59.4 ± 1.2%; NH₄⁺-N: 78.2 ± 1.6%; and TN: 77.8 ± 1.2%), smaller internal impedance Rₜ (∼6 Ω), higher exchange current density i₀ (2.1 × 10⁻⁴ A cm⁻²), and a larger catalytic current j₀ (704 μA cm⁻²) with 60% leachate than those with 10% and 20% leachate, resulting in a power output of 298 ± 22 mW m⁻². Ammonium could be incorporated by chemoautotrophic bacteria to produce organic compounds that could be further utilized by heterotrophs to generate power when biodegradable organic matters are depleted. Three conversion pathways of nitrogen might be involved, including NH₄⁺ diffusion from anode to cathode chamber, nitrification, and the denitrification process. Additionally, cyclic voltammetry tests showed that both the direct electron transfer (DET) and the mediator electron transfer in bioanode were involved and dominated by DET. The microbial analysis revealed that the bioanode was dominated by salt-tolerant denitrifying bacteria (38.5%), which was deduced to be the key functional microorganism. The electrochemically active bacteria decreased significantly from 61.7% to 4% over three stages of leachate treatment. Overall, the SC-MFC has demonstrated the potential for wastewater treatment along with energy harvesting and provides a new avenue toward sustainable leachate management.

Bioelectrochemical systems (BESs) convert the energy present in wastewater to recover resources like bioelectricity, hydrogen, nutrients, heavy metals, minerals, and industrial chemicals. Various aspects of BES have been discussed here along with their applications and other advantages towards bioenergy recovery. More scientifically organized cross-discipline research efforts are required to scale-up these systems and to get benefit of recovering useful energy from waste materials. Full-scale implementation of bioelectrochemical wastewater treatment is complicated because certain microbiological, technological, and economic challenges need to be resolved that have not previously been encountered in any other wastewater treatment system. BES has higher prospects for in situ remediation of polluted water body or marshy soils and sediments. This technology is likely to evolve as a way of treating sewage, industrial, or agricultural wastewater, not only by lowering the amount of energy required, but at the same time producing electricity, hydrogen, or other chemicals of high value. Thus, after improving the performance of the BES, widening the scope for products recovery by developing better understanding of the process and with efforts to reduce its production cost, it can become a sustainable technology for treatment of wastewater with added advantage of recovery of resources and bioenergy.

Microbial fuel cell (MFC) is a sustainable technology to treat cattle manure slurry (CMS) for converting chemical energy to bioelectricity. In this work, two types of allochthonous inoculum including activated sludge (AS) and domestic sewage (DS) were added into the MFC systems to enhance anode biofilm formation and electricity generation. Results indicated that MFCs (AS + CMS) obtained the maximum electricity output with voltage approaching 577 ± 7 mV (~ 196 h), followed by MFCs (DS + CMS) (520 ± 21 mV, ~ 236 h) and then MFCs with autochthonous inoculum (429 ± 62 mV, ~ 263.5 h). Though the raw cattle manure slurry (RCMS) could facilitate electricity production in MFCs, the addition of allochthonous inoculum (AS/DS) significantly reduced the startup time and enhanced the output voltage. Moreover, the maximum power (1.259 ± 0.015 W/m²) and the highest COD removal (84.72 ± 0.48%) were obtained in MFCs (AS + CMS). With regard to microbial community, Illumina HiSeq of the 16S rRNA gene was employed in this work and the exoelectrogens (Geobacter and Shewanella) were identified as the dominant members on all anode biofilms in MFCs. For anode microbial diversity, the MFCs (AS + CMS) outperformed MFCs (DS + CMS) and MFCs (RCMS), allowing the occurrence of the fermentative (e.g., Bacteroides) and nitrogen fixation bacteria (e.g., Azoarcus and Sterolibacterium) which enabled the efficient degradation of the slurry. This study provided a feasible strategy to analyze the anode biofilm formation by adding allochthonous inoculum and some implications for quick startup of MFC reactors for CMS treatment.

The present work focused on the utilization of three local wastes, i.e., rambutan (Nephelium lappaceum), langsat (Lansium parasiticum), and mango (Mangifera indica) wastes, as organic substrates in a benthic microbial fuel cell (BMFC) to reduce the cadmium and lead concentrations from synthetic water. Out of the three wastes, the mango waste promoted a maximum current density (87.71 mA/m²) along with 78% and 80% removal efficiencies for Cd²⁺ and Pb²⁺, respectively. The bacterial identification proved that Klebsiella pneumoniae, Enterobacter, and Citrobacter were responsible for metal removal and energy generation. In the present work, the BMFC mechanism, current challenges, and future recommendations are also enclosed.

Strategic valorization of readily available sugarcane bagasse (SB) is very important for waste management and sustainable biorefinery. Conventional SB pretreatment methods are ineffective to meet the requirement for industrial adaptation. Several past studies have highlighted different pretreatment procedures which are lacking environmentally benign characteristics and effective SB bioconversion. This article provides an in-depth review of a variety of environmentally acceptable thermochemical and biological pretreatment techniques for SB. Advancements in the conversion processes such as pyrolysis, liquefaction, gasification, cogeneration, lignin conversion, and cellulose conversion via fermentation processes are critically reviewed for the formation of an extensive array of industrially relevant products such as biofuels, bioelectricity, bioplastics, bio adsorbents, and organic acids. This article would provide comprehensive insights into several crucial aspects of thermochemical and biological conversion processes, including systematic perceptions and scientific developments for value-added products from SB valorization. Moreover, it would lead to determining efficient pretreatment and/or conversion processes for sustainable development of industrial-scale sugarcane-based biorefinery.

A microbial fuel cell coupled with constructed wetland (CW-MFC) was built to remove heavy metals (Zn and Ni) from sludge. The performance for the effects of substrates (granular activated carbon (GAC), ceramsite) and plants (Iris pseudacorus, water hyacinth) towards the heavy metal treatment as well as electricity generation was systematically investigated to determine the optimal constructions of CW-MFCs. The CW-MFC systems possessed higher Zn and Ni removal efficiencies as compared to CW. The maximal removal rates of Zn (76.88%) and Ni (66.02%) were obtained in system CW-MFC based on GAC and water hyacinth (GAC- and WH-CW-MFC). Correspondingly, the system produced the maximum voltage of 534.30 mV and power density of 70.86 mW·m⁻³, respectively. Plant roots and electrodes contributed supremely to the removal of heavy metals, especially for GAC- and WH-CW-MFC systems. The coincident enrichment rates of Zn and Ni reached 21.10% and 26.04% for plant roots and 14.48% and 16.50% for electrodes, respectively. A majority of the heavy metals on the sludge surface were confirmed as Zn and Ni. Furthermore, the high-valence Zn and Ni were effectively reduced to low-valence or elemental metals. This study provides a theoretical guidance for the optimal construction of CW-MFC and the resource utilization of sludge containing heavy metals.

Microbial fuel cell is an efficient technology to reduce pollutants of the heavy metal ions. Herein, a dual-chamber microbial fuel cell (MFC) coupled with abio-cathode and electrochemically active bacteria is fabricated to treat Cr (VI) containing wastewater and harvest bioelectricity simultaneously. To investigate the wide application of MFC for various industries, four different concentrations of Cr (VI) (6 mg/L, 15 mg/L, 40 mg/L, 100 mg/L) are used to explore the removal efficiency of Cr (VI) and the corresponding power performance. We find that the power performance gradually increases with the increment of the initial Cr (VI) concentration. Significantly, a maximum power density of 35.3 mW/m² can be achieved with the initial concentration of 100mg/L Cr (VI), while MFC only generate negligible power density (2.6 mW/m²) without the presence of Cr (VI). Meanwhile, MFC combined with the initial Cr (VI) concentration of 15 mg/L shows the highest Cr (VI) removal of 66.5%. Moreover, partial precipitates are found on the cathode surface and X-ray photoelectron spectroscopy (XPS) analysis has demonstrated that the Cr (VI) is successfully reduced into Cr (III). This study offers an alternative technology to remove Cr (VI) and synchronous electricity generation.

Worldwide, the requirement of electrical energy has increased with an increase in population. Thus, there is a need to develop an alternative source of sustainable energy, such as microbial fuel cell (MFC). MFC is a better option of energy generation and can provide a renewable resource which utilizes wastewater into power by the help of microorganisms. MFC is one of the advanced methods for treating wastewater and simultaneously producing current and voltage. Dual-chambered MFC was prepared using two plastic boxes (500 ml) by using wastewater as an anolyte. Different types of mediators are used in MFC including methylene blue, potassium ferricyanide, and EDTA to facilitate and higher the efficiency of electron transfer from the MFC to the electrode. Maximum OCV and current output of sample 1 (Budha Talab pond water) were 0.86 V and 75.1 mA and of sample 2 (Jaypee cement plant) were 1.42 V and 122 mA. The maximum current output of sample 3 (sugar industry, sewage waste, NIT canteen) was 1.3 V. Various physiochemical parameters such as dissolved oxygen (DO), biochemical oxygen demand (BOD), and chemical oxygen demand (COD) were analyzed which affect the power output. The obtained result concluded that wastewater should be feed at a certain time interval to avoid the loss of substrate for organisms in the anodic chamber which lead to the death of the microorganism. Among all, sugar industry wastewater has a high potential for power generation as their physiochemical results are suitable for better power output.

The surface morphology of biocathode was one of the limiting factors for microbial fuel cell (MFC) design. Up-flow membrane-less single-chambered MFC (UFML MFC) was used to investigate the effect of surface morphology of carbon material as aqueous biocathode. Pt-loaded carbon paper, carbon felt, and carbon plate were examined and compared on the power output, surface morphology for biofilm formation, Coulombic efficiency (CE), and chemical oxygen demand (COD) reduction. The COD reduction was up to 90 % in UFML MFC with Pt-loaded carbon paper, carbon felt, and carbon plate as aqueous biocathodes. The results obtained showed that the performance in voltage output was not related to internal resistance but mainly due to the ability of cathode material in oxygen reduction process. The performance of voltage output with different materials as aqueous biocathode was mainly based on to the surface morphology as it was related to the ability of biofilm formation. Roughness of aqueous biocathode’s surface morphology could prompt the biofilm growth, while biofilm overgrowth on aqueous biocathode could decrease voltage output. Therefore, smoother surface morphology of aqueous biocathode is more suitable for long-term operation.