Application of alternating current in electrocoagulation and activation of persulfate (AEC-PS) for the effective removal of humic acid (HA) from aqueous solution was evaluated. In order to optimize the removal efficiency HA by the AEC-PS process, several influencing parameters such as pH, reaction time, PS dose, current density (CD), concentration of NaCl, initial concentration of HA, and coexisting cations and anions influence were investigated. From the batch experiments, the highest HA removal efficiency obtained was 99.4 ± 0.5% at pH of 5, reaction time of 25 min, CD of 4.5 mA/cm², PS dose of 200 mg/L, and NaCl concentration of 0.75 g/L for an initial HA concentration of 30 mg/L. When CD increased from 1.25 to 4.5 mA/cm², the HA removal efficiency was improved from 88.8 ± 4.4% to 96.1 ± 1.5%. In addition, the type of coexisting cations and anions exerted a significant role, leading to a reduction in the removal efficiency of HA. To investigate the dominant free activated radical, radical scavengers such as tert-butyl alcohol and ethanol were employed. It was observed that both OH and SO₄⁻ radicals substantially contributed to the removal of HA, and the contribution of SO₄⁻ radical was higher than that of OH radical, suggesting that AEC-PS process could serve as a novel and effective treatment technique for the removal of organic matters from aqueous sources.

Bioaccessibility extractions are increasingly applied to measure the fraction of pollutants in soil, sediment and biochar, which can be released under environmentally or physiologically relevant conditions. However, the bioaccessibility of hydrophobic organic chemicals (HOCs) can be markedly underestimated when the sink capacity of the extraction medium is insufficient. Here, a novel method called “Membrane Enhanced Bioaccessibility Extraction” (MEBE) applies a semipermeable membrane to physically separate an aqueous desorption medium that sets the desorption conditions from an organic medium that serves as acceptor phase and infinite sink. The specific MEBE method combines HOC (1) desorption into a 2-hydroxypropyl-β-cyclodextrin solution, (2) transfer through a low-density polyethylene (LDPE) membrane and (3) release into ethanol, serving as analytical acceptor phase. The surface to volume ratio within the LDPE membrane is maximized for rapid depletion of desorbed molecules, and the capacity ratio between the acceptor phase and the environmental sample is maximized to achieve infinite sink conditions. Several experiments were conducted for developing, optimizing and pre-testing the method, which was then applied to four soils polluted with polycyclic aromatic hydrocarbons. MEBE minimized sample preparation and yielded a solvent extract readily analyzable by HPLC. This study focused on the proof-of-principle testing of the MEBE concept, which now can be extended and applied to other samples and desorption media.

A self-assembly method was adopted to synthesize loading architecture of ZnO/g-C₃N₄ heterojunction composites by hybridization of g-C₃N₄ nanosheets and ZnO nanoparticles utilizing a refluxing method at a low temperature. More importantly, we provided a novel route to regulate the π-π restacking thickness of the g-C₃N₄ nanosheets among ZnO/g-C₃N₄ composites by the controlling the refluxing time in the ethanol solution, which can optimize the surface hybrid structure, optical response and photocatalytic activity. Among all of samples, ZnO/g-C₃N₄ composites with a refluxing 12 h showed the enhancement of photocatalytic activity. The enhanced visible light photocatalytic activity of ZCN-12 composites can be ascribed to the synergistic effects of the construction of hybrid structures, reduction of structural defects of g-C₃N₄ nanosheets and suitable π-π restacking g-C₃N₄ nanosheets loading thickness.

Removal of dissolved sulfide contaminants from aqueous model solution using bio-derived porous graphitic carbon (PGC) impregnated with δ-MnO₂ was investigated. The composite adsorbent was synthesized using the chemical wet deposition method wherein MnO₂ was deposited on carbon walls through an in-situ reaction between permanganate and ethanol. Formation of transition metal oxide of manganese in the form of birnessite nanoparticles on interconnected PGC cell structure was confirmed by transmission electron microscopy, scanning electron microscopy, elemental analysis, and X-Ray diffraction characterization studies. The composite nanomaterial was tested for sulfide removal from aqueous solution at various conditions, including the pH, adsorbent dosage, initial solution concentration, and contact time. Adsorption results demonstrated an excellent adsorption capacity of ca. 90% within 20 min of contact time at 298 K. Equilibrium data collected from batch adsorption experiments fitted well with the Langmuir isotherm model (KL = 190 L/mg; R² = 0.99). The maximum adsorption capacity of the composite was estimated as 526.3 mg S²⁻/g at highly alkaline conditions compared to ca. 340 mg/g for a δ-MnO₂ adsorbent. Adsorptive oxidation of sulfides on composite MnO₂-PGC adsorbent was found to be controlled by the chemisorption process in accordance with the pseudo-second-order reaction model. Characterization of spent adsorbents revealed that sulfide was removed through adsorptive oxidation resulting in the formation of agglomerated particles of metal sulfate complexes and elemental sulfur. Analysis of reaction mechanism revealed that both MnO₂ and PGC played a role in the adsorptive oxidation of sulfides to CaSO₄ and elemental sulfur.

The cobalt ferrite-reduced oxidized graphene (CoFe2O4/rGO) catalyst was synthesized by hydrothermal method and characterized by Powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Scanning electron microscope (SEM), Brunauere Emmette Teller (BET) and Hysteresis loop. For developing a new method of removing elemental mercury (Hg0) from flue gas, the effects of catalyst dosage, PMS concentration, solution pH and reaction temperature on the removal efficiency were investigated experimentally by using peroxymonosulfate (PMS) catalyzed by CoFe2O4/rGO at a self-made bubbling reactor. The average removal efficiency of Hg0 in a 30-min period reached 95.56%, when CoFe2O4/rGO dosage was 0.288 g/L, PMS concentration was 3.5 mmol/L, solution pH was 5.5 and reaction temperature was 55 °C. Meanwhile, based on the free radical quenching experiments, in which, ethyl alcohol and tert butyl alcohol were used as quenchers to prove indirectly the presence of •OH and SO4•−, the characterizations of catalysts and reaction products, and the existing results from other scholars. The reaction mechanism was proposed.

Isotopic fractionation of pollutants in terrestrial or aqueous environments is a well-recognized means by which to track different processes during remediation. As a complement to the common practice of measuring the change in isotope ratio for the whole molecule using isotope ratio monitoring by mass spectrometry (irm-MS), position-specific isotope analysis (PSIA) can provide further information that can be exploited to investigate source and remediation of soil and water pollutants. Position-specific fractionation originates from either degradative or partitioning processes. We show that isotope ratio monitoring by 13C NMR (irm-13C NMR) spectrometry can be effectively applied to methyl tert-butylether, toluene, ethanol and trichloroethene to obtain this position-specific data for partitioning. It is found that each compound exhibits characteristic position-specific isotope fractionation patterns, and that these are modulated by the type of evaporative process occurring. Such data should help refine models of how remediation is taking place, hence back-tracking to identify pollutant sources.

GeoChip, a comprehensive gene microarray, was used to examine changes in microbial functional gene structure throughout the 4-year life cycle of a pilot-scale ethanol blend plume, including 2-year continuous released followed by plume disappearance after source removal. Canonical correlation analysis (CCA) and Mantel tests showed that dissolved O2 (which was depleted within 5 days of initiating the release and rebounded 194 days after source removal) was the most influential environmental factor on community structure. Initially, the abundance of anaerobic BTEX degradation genes increased significantly while that of aerobic BTEX degradation genes decreased. Gene abundance for N fixation, nitrification, P utilization, sulfate reduction and S oxidation also increased, potentially changing associated biogeochemical cycle dynamics. After plume disappearance, most genes returned to pre-release abundance levels, but the final functional structure significantly differed from pre-release conditions. Overall, observed successions of functional structure reflected adaptive responses that were conducive to biodegradation of ethanol-blend releases.

The fate of fuel releases largely depends on the poorly-understood response in microbial community structure and function. Here, we evaluate the impacts to the microbial community resulting from a pilot-scale continuous release (10 months) of a 10% v:v ethanol solution mixed with benzene and toluene (50 mg/L each). Microbial population shifts were characterized by pyrosequencing-based 16S rRNA analysis and by quantitative PCR targeting Bacteria, Archaea, and functional genes for methanogenesis (mcrA), acetogenesis (fhs) and aerobic degradation of aromatic hydrocarbons (PHE), which could occur in hypoxic micro-environments. The release stimulated microbial growth, increased species richness and diversity, and selected for genotypes involved in fermentative degradation (the relative abundance of mcrA and fhs increased 18- and 6-fold, respectively). The growth of putative hydrocarbon degraders and commensal anaerobes, and increases in microbial diversity and in degradation rates suggest an adaptive response that increases the potential for natural attenuation of ethanol blend releases.

The aim of this study was to develop a new experimental setup to determine parallel the emissions of greenhouse gases (GHG) and volatile organic compounds (VOCs) from silage during the opening as well as the subsequent aerobic storage phase of the complete bale without wrapping film. For this purpose, a special silage respiration chamber was used in which a silage bale could be examined. The gas analysis (CO₂, methanol, ethanol, ethyl acetate) of inlet, ambient and outlet air of the silage respiration chamber was carried out by photoacoustic spectroscopy. The gas samples taken inside the bale were analysed by gas chromatography for CO₂, O₂, CH₄, and N₂O. Three silage bales (grass and lucerne) as the smallest silage unit commonly used in practice were examined. The emission behaviour of the bales was recorded during experimental periods up to 55 days. The results allow a differentiation of the outgassing processes. On the one hand, gases produced during the anaerobic ensiling process (CO₂, CH₄, N₂O) are released once in a large amount during the first experimental hours after opening the silage. On the other hand, a continuous outgassing process takes place, which is particularly true for the VOCs ethanol, methanol, and ethyl acetate, whereby VOC emissions increase with rising ambient air temperatures. In this study, the emissions during the first 600 experimental hours from the grass silage bale and lucerne silage bale were 2313 g and 2612 g CO₂, 17.6 g and 145.2 g methanol, 132.3 g and 675.9 g ethanol, 55.1 g and 66.2 g ethyl acetate, respectively. Nevertheless, the focus of this study was on the technical recording of gas concentrations inside the silage bale itself and the emissions in the ambient air of the bale. For a better interpretation of the data, additional factors should be considered in further investigations.