According to fire accident statistics, fires in buildings are increasing. The flame-retardant performance of insulation materials is considered an important factor for preventing the spread of fire and ensuring evacuation. This study evaluated the flame-retardant performance and combustion characteristics of four types of organic thermal insulation used as core materials in sandwich panels. The flame-retardant performance evaluation based on total heat release and heat release rate revealed that phenolic foam (PF) satisfied the criteria for non-combustible grade insulation. An analysis of the hazardous gases released while combustion of the four insulation materials indicated that a significant amount of CO was released—an average of 19,000 ppm or higher—in the rigid urethan foam (PIR) and spray-type polyurethane foam (SPU). The fractional effective dose (FED) value was derived from the gas analysis results according to ISO 13344. PIR and SPU had an average FED value of 2.0 or higher and were identified as very dangerous in the case of fire accidents. Moreover, the evacuation time in the case of a fire in a warehouse-type building was comprehensively analyzed considering the material, size, and height for the four types of insulation. PIR was the most vulnerable to fire, and for PF, the danger limit was not reached until the end of the simulation.

Radon is a natural radioactive gas present in the environment, which is considered as the second most important lung cancer cause worldwide. Currently, radon gas is under focus and was classified as contaminant of emerging concern, which is responsible for serious biological/health effects in human. In presented work we propose the numerical model and analysis method for radon diffusion rate measurements and radon transport parameters determination. The experimental setup for radon diffusion was built in a classical, two chamber configuration, in which the radon source and outlet reservoirs are separated by the sample being tested. The main difference with previously known systems is utilization of only one radon detector, what was achieved by a careful characterization of the Rn-222 source and development of a numerical model, which allows for exact determination of radon transport parameters by fitting simulated radon concentration profile in the outlet reservoir to experimental data. For verification of the developed system, several insulation materials commonly used in building industry and civil engineering, as well as, common building materials (gypsum, hardened cement paste, concrete) were tested for radon diffusion rate through these barriers. The results of radon transmittance, permeability and diffusion coefficients for investigated materials are in compliance with values known previously from the literature. The analysis method is fast and efficient, and requires measurement period varying from a dozen or so hours up to 2–3 days depending on material properties. The described method is entirely based on a numerical analysis of the proposed differential equation model using freely available SCILAB software and experimental data obtained during sample measurements.

Insulation materials are essential components in construction, and their main objective is to increase the efficiency of thermal energy by minimizing internal and external thermal exchange. Accordingly, research and development studies are being actively conducted to increase the thermal resistance of insulation materials, and high-performance insulation materials that use organic chemicals have been developed after industrialization. However, thermal insulation comprising chemicals poses a potential risk of pollutant emissions and can cause health problems. In this study, five types of insulation materials and the contaminants generated from the building materials used in insulation construction were quantitatively analyzed. In addition, an empirical study on the discharge of pollutants was conducted using a test bed, and the effects of the pollutants discharged from the insulation material on the indoor environment were examined by analyzing the pollutant concentration for 90 days. In addition, we analyzed the effect of an insulation material on an indoor environment through the standard specifications. Moreover, the necessity of legal management of the emission of contaminants from insulation materials was proposed based on the empirical research results.

As energy use in the building sector is increasing worldwide, building materials with characteristics that save energy are becoming increasingly important; in addition, there is an emerging need for high-performance insulation materials with low thermal conductivity. However, thermal insulation should consider thermal conductivity, which is the main performance parameter, in addition to the water adsorption rate, acidity, and deformation and expansion due to drying conditions. This study evaluated the main performance of 21 insulation materials used at construction sites to objectively and clearly evaluate their overall performance, including their thermal conductivity. Thermal conductivity was measured by the heat flow meter method according to ASTM C518 and ISO 8301 standards; it was also evaluated according to the drying conditions. The water absorption rate was evaluated by ISO 2896 to ensure the sustainability and long-term thermal conductivity performance of the material. Acidity was evaluated with ASTM E861 to reduce the environmental load of the buildings and soil. The results of this study reviewed an appropriate method to measure the main performance according to the type of insulation.

Epilithic mosses are characterized by insulation from substratum N and hence meet their N demand only by deposited N. This study investigated tissue C, total Chl and δ13C of epilithic mosses along 2 transects across Guiyang urban (SW China), aiming at testing their responses to N deposition. Tissue C and total Chl decreased from the urban to rural, but δ13Cmoss became less negative. With measurements of atmospheric CO2 and δ13CO2, elevated N deposition was inferred as a primary factor for changes in moss C and isotopic signatures. Correlations between total Chl, tissue C and N signals indicated a nutritional effect on C fixation of epilithic mosses, but the response of δ13Cmoss to N deposition could not be clearly differentiated from effects of other factors. Collective evidences suggest that C signals of epilithic mosses are useful proxies for N deposition but further works on physiological mechanisms are still needed.

It is well known, that in case of oil spill, seabirds are among the groups of animals most vulnerable. Even small amounts of oil can have lethal effects by destroying the waterproofing of their plumage, leading to loss of insulation and buoyancy. In the Arctic these impacts are intensified. To protect seabirds, a rapid removal of oil is crucial and in situ burning could be an efficient method. In the present work exposure effects of oil and burn residue in different doses was studied on seabird feathers from legally hunted Common eider (Somateria mollissima) by examining changes in total weight of the feather and damages on the microstructure (Amalgamation Index) of the feathers before and after exposure. The results of the experiments indicate that burn residues from in situ burning of an oil spill have similar or larger fouling and damaging effects on seabird feathers, as compared to fresh oil.

Because of global environmental problems, low-carbon agriculture has gained increasing importance both in developed and developing countries. Hence, there is a need to find ways to develop more efficient agricultural systems. The purpose of this article is to identify the drivers of low-carbon agriculture on farms in the Wielkopolska region (in Poland). We aimed to take an original approach to investigate low-carbon agriculture with a unique set of different economic and environmental variables and contribute to the literature, which is not very extensive in terms of microeconomic research, including research on farmers in the Wielkopolska region. Therefore, we employed a multiple-factor measurement model for structural equation modeling (SEM) of data collected individually from 120 farms in 2020. As a result, we formulated the following conclusions: the increasing productivity of factors (land, labor, and capital) have a positive effect on low-carbon farming, just as increasing fertilizer and energy efficiency. Moreover, thermal insulation is also important for low-carbon agriculture, with efficiency of fertilizer use being the most important factor. We believe that the issues of farm use of fertilizers and thermal insulation of buildings should be more broadly included in energy policy, both at the national and the European Union (EU) levels. Some of these factors however are already present in the common agricultural policy (CAP) for 2021–2027.

A solar pond is a simple system that collects and stores heat for thermal and electrical applications. Heat storage and heat extraction are the key factors in the solar pond. Salt is added to the pond with fresh water to form a salinity gradient solar pond (SGSP). The solar pond comprises of three zones, namely, the upper convective zone (UCZ), the non-convective zone (NCZ) and the lower convective zone (LCZ). The LCZ is also called the storage zone. Generally, the LCZ stores the heat energy of the incoming solar radiation, and this heat may be used for various applications. In this paper, a review is done on the study of solar ponds with various designs and modifications, heating methods, use of floating devices, use of baffle plates, use of heat exchangers, use of flat plate collectors, use of different types of insulation, etc.

The water quality of Lake Mariut has been deteriorated for about 5 decades due to continuous discharge of agricultural, municipal, and industrial wastes from Alexandria City and the adjacent land. During the past two decades, some steps were taken for rehabilitation of the lake through primary treatment of the discharged wastes and insulation of the polluted wastewater of QD from the water body in the main basin of the lake. Several parameters of water quality at the surface and near bottom were measured at twelve locations during winter (January) and summer (August) of 2013 and 2014. The present study revealed that the lake water appeared to be well aerated but still containing high concentrations of N and P and suffering hyper-eutrophic conditions. The water quality index (WQI) reflected medium condition in the lake and bad condition in the diverted drains. The P-budget calculation displayed that TP input into the LMMB from UDᵤₛ and resuspension process from sediments exceeded the output by out flowing at UDdₛ and settling.

The dust removal performance of two types of modified electrode electrostatic precipitator systems was evaluated and compared with that of a conventional aluminum plate electrode using laboratory-scale experiments. In the novel electrode systems, the electrode surface was coated with activated carbon using a mixed slurry containing carbon black, polyvinyl acetate, and methanol. The modification of the electrode surface improved dust precipitation by increasing the specific capacitance of the electrode. The modification also lowered the electrode’s resistance and increased its specific surface area. The optimum electrode spacing and electric voltage supply were determined using batch-type tests. In addition, dielectric insulators were applied as a partition between the oppositely charged electrodes equipped with the modified electrode plates. Multi-layered office paper cut to the same size as the electrodes was used as an insulating material. The addition of the insulator resulted in excellent improvement in the dust removal performance by minimizing the back-corona discharge phenomenon as well as doubling the dust collecting surface. Continuous dust removal tests with the three electrode systems revealed that whereas the conventional aluminum electrode exhibited 54 % dust removal, the activated carbon (AC)-coated system showed 85 % and AC-coated + insulator system showed 90 % and higher dust removal efficiency.