The concentrations of nitrate (NO₃⁻), major ions, and dissolved inorganic carbon (DIC) and the stable carbon isotopes of DIC (δ¹³CDIC) in shallow groundwater below a 45 × 60 m residential property was investigated over a period of 38 months. Our aim was to identify the processes which control the spatial and temporal distribution of NO₃⁻ in the shallow groundwater and assess water-rock interactions linked to denitrification. Groundwater sampled quarterly from eight locations showed an average NO₃⁻ concentration of 36.8 mg/L and a range between 0.1 and 214.9 mg/L compared to the US EPA maximum contaminant level of 10 mg/L. Heterogeneity in nitrate distribution was from residential application of N-based fertilizers offsite and from onsite application on flower beds and for lawn care. The temporal behavior of nitrate at all eight groundwater locations was markedly different and independent of seasonal hydrologic variations. Nitrate attenuation was spatially controlled by heterogeneous denitrification and rain dilution near roof drains. Groundwater locations with active denitrification were characterized by higher DIC concentrations and lower δ¹³CDIC from organic carbon mineralization and by higher ionic concentrations from weathering of aquifer minerals. The variation in the relative standard deviations (RSD) of the measured parameters over space (RSD-s) and time (RSD-t) was highest for NO₃⁻ associated with variable spatiotemporal input and lowest for pH, pCO₂, and δ¹³CDIC indirectly controlled by denitrification. Denitrification induced mineral weathering products such as DIC, Ca²⁺, Mg²⁺, and HCO₃⁻ showed medium to high RSD-s and RSD-t. The RSD-s and RSD-t were positively correlated (R² = 0.85) with the RSD-s showing approximately twofold higher magnitude than RSD-t due to greater variability between monitoring wells locations than variability at each groundwater location over time. Nitrate contamination and denitrification represent important long-term driver of aquifer weathering and changes in groundwater geochemistry below residential communities.

The objective of this study is to assess the effect of orientation, glazing proportion and aspect ratio of building zones on heat fluxes through their surfaces, under specific environmental conditions. The investigation is carried out for thermally-insulated building zones with a varying facade orientation corresponding to each cardinal point, during the winter period in the northern Greek region. For this purpose, three glazing-to-facade ratios (GR) are taken into account; along with the glazing ratio the influence of the glazing U value is also considered. Regarding the impact of the fenestration layout geometry, five different building aspect ratio profiles are examined. Thermal fluxes are assessed for two different indoor temperature settings, while the operation of the heating unit is assumed to be continuous. The transient thermal analysis with its mathematical formulation and solution are based on the thermal-network modelling approach, while the solar heat gain through glazing relies on the sunlit-pattern approach; in this way, the stricken by the solar rays glazing area is projected onto any interior surfaces to form the so called “sunlit” areas. As the orientation, glazing proportion and aspect ratio of the building zone vary, so do the sizes and shapes of the illuminated “sunlit” areas. Accordingly, the delivered into the zone direct solar energy and its diffused and ground reflected components can be determined. The adopted methodology provides a more accurate determination of solar heat gain with respect to glazing proportion and orientation as well as zone aspect ratio. With regard to surface orientation, glazing proportion and aspect ratio, computer results demonstrate the improvement of the thermal performance for a building zone with a south oriented glazing surface, as well as the deterioration for the other surface orientations; relative increases/decreases in the energy fluxes of a rectangular shaped building zone compared to a square-shaped building zone can reach up to 50%/100%.

Descriptor 9 (D9) of the European Union Marine Strategy Framework Directive refers to the compliance of contaminant levels in fish and other seafood of a defined marine region or subregion with human health threshold values. This requires georeferenced samples that are often difficult to obtain when relying on commercial fisheries or programs designed for monitoring human exposure. The present study examines whether georeferenced samples of blue mussel (Mytilus edulis) and eelpout (Zoarces viviparus) fillet of the German environmental specimen bank (ESB) can be used in this context. The suitability of the ESB samples, procedures, and analytical methods is evaluated with respect to D9 requirements. Based on ESB data for the D9 relevant contaminants Pb, Cd, Hg, ∑4 PAHs, PCDD/Fs, dioxin-like (dl)-PCBs, and indicator non-dl-PCBs and the potentially relevant substances TBT, PFOS, PBDE, and HBCDD, the Good Environmental Status for D9 is assessed at the ESB sites in the North and Baltic Seas. The overall evaluation indicates that ESB samples are suitable for D9 assessment with the limitation that only coastal areas of the North and Baltic Seas are covered. Over a period of up to 30 years, concentrations of the D9 relevant contaminants were well below the maximum levels allowed for human consumption.

In this study, 15 representative surface waters and sediments and seven typical fish were collected during the wet season in 2016 to explore the occurrence, chemical fractionation, and ecological risk of heavy metals (Cu, Zn, Pb, Cd, Cr, Hg, As, and Ni) in aquatic ecosystems of Dongting Lake in China. In surface water, the concentrations of all elements were lower than the third grade of the surface water quality standards (GB3838-2002). The highest concentrations of Zn, Pb, Cd, Ni, and Cu were found in the outlet of Dongting Lake, whereas As and Cr were highest in the Xiangjiang River Delta area. In surface sediments, the concentration decreased in the order of Zn > Cr > Pb > Cu > Ni > As>Cd > Hg; the highest concentration of all elements, except for Hg, was located in the Xiangjiang River Delta area; for chemical fractionation, Cr, Hg, Zn, As, Ni, and Cu were mainly residual fractionation; and Pb and Cd were mainly in a reducible state and fraction soluble in acid, respectively. In fish muscle, the concentrations of all elements were lower than relevant standards; the highest concentration appeared in fish living in the middle-lower and demersal layers. As for the feeding habits of fish, the average concentration decreased in the order of carnivorous > omnivorous > herbivorous fish. The potential ecological risk and the ratio of secondary phase to primary phase assessment showed that Cd and Hg had the highest ecological risk and that Cd and Pb had a high risk of secondary release. A health risk assessment showed that drinking water and fish for consumption in urban and rural areas around Dongting Lake were in the acceptable level.

The current work focuses on the experimental investigation to analyze the combustion and emission characteristics of a direct injection diesel engine fueled with neat biodiesel (BD100) and different proportions of cyclohexanol blends as a fuel additive in various volume fractions. Cyclohexanol is dispersed into a neat biodiesel in a volume fraction of 10, 20, and 30 vol%. The biodiesel is produced from neem oil by the conventional transesterification process. The experimental results revealed that with the increased cyclohexanol fraction, the combustion was found smooth. The addition of cyclohexanol has a positive influence on various physical and chemical properties of neat biodiesel. The in-cylinder pressure is comparatively low for diesel followed by cyclohexanol and biodiesel blends when compared with neat biodiesel. This is due to shorter ignition delay period. The heat-release rate of neat biodiesel is the highest among all fuels. The overall HC emission of BD70COH30 is 12.19% lower than BD100 and 16.34% lower than diesel. The overall CO₂ emission of BD70COH30 is 13.91% higher than BD100 and 19.5% higher than diesel. The overall NOₓ emission of BD70COH30 is 5.31% lower than BD100 at all load engine operations. The presence of 10, 20, and 30% of cyclohexanol in biodiesel decreased smoke emissions as compared with neat biodiesel and diesel. The overall smoke emission of BD70COH30 is 19.23% lower than BD100 and 25.51% lower than diesel. The overall CO emission of cyclohexanol blended with biodiesel by 30 vol% (BD70COH30) is 17% lower than neat biodiesel and 21.8% lower than diesel. Based on the outcome of this study, neem oil biodiesel and cyclohexanol blends can be employed as a potential alternative fuel for existing unmodified diesel engines owing to its lesser emission characteristics.

Novel low-cost bark-based magnetic iron oxide particles (BMIOPs) were synthesized and investigated for the removal of As(III) in drinking water. The synthesized BMIOP had a saturation magnetization value of 38.62 emug⁻¹ which was found to be enough for the magnetic separation of exhausted BMIOP after As(III) adsorption. Parameters like agitation speed, adsorbent dosage, contact time, pH, temperature, and initial concentration were thoroughly investigated. Langmuir, Freundlich, and Dubinin–Radushkevich isotherms were used for the modeling of experiments and observed a maximum adsorption (19.61 mg g⁻¹) of As(III) by Langmuir isotherm. Kinetics of As(III) sorption were well correlated with the coefficients in pseudo-first-order than the pseudo-second-order rate equation. Thermodynamic parameter investigation revealed that As(III) sorption process is endothermic, feasible, and spontaneous. BMIOP emerged as less expensive adsorbent for the abatement of arsenic ion from the drinking water. BMIOP showed 13.58 mg g⁻¹ adsorption capacity when As(V) alone is present, while it is 9.43 and 7.04 mg g⁻¹ for As(V) and As(III), respectively, when present together in the water. Graphical Abstract ᅟ

This study was carried out using indoor controlled experiments to study the arsenic (As) uptake, biotransformation, and release behaviors of freshwater algae under growth stress. Three freshwater algae, Microcystis aeruginosa, Anabaena flosaquae, and Chlorella sp., were chosen. Two types of inhibitors, e.g., Cu²⁺ and isothiazolinone, were employed to inhibit the growth of the algae. The algae were cultivated to a logarithmic stage in growth media containing 0.1 mg/L P; then, 0.8 mg/L As in the form of arsenate (iAsⱽ) was added, while both inhibitors were simultaneously added at dosages of 0.1 and 0.3 mg/L, with no addition of inhibitors in the control. After 2 days of exposure, the average growth rate (μ₂d) was measured to represent the growth rates of the algae cells; the extra- and intracellular As concentrations in various forms, i.e., arsenate, arsenite (iAsᴵᴵᴵ), monomethyl arsenic (MMA), and dimethyl arsenic (DMA), were also measured. Without inhibitors, the average growth rate followed the order of M. aeruginosa, Chlorella sp., and A. flosaquae, with the growth rate of M. aeruginosa significantly higher than that of the other two algae. However, when Cu²⁺ was added as an external inhibitor, the order of the average growth rate for the three algae became partially reversed, suggesting differentiation of the algae in response to the inhibitor. This differentiation can be seen by the reduction in the average growth rate of M. aeruginosa, which was as high as 1730% at the 0.3-mg/L Cu²⁺ dosage when compared with the control, while for the other two algae, much fewer changes were seen. The great reduction in M. aeruginosa growth rate was accompanied by increases in extracellular iAsⱽ and iAsᴵᴵᴵ and intracellular iAsⱽ concentrations in the algae, indicating that As transformation is related to the growth of this algae. Much fewer or neglectable changes in growth were observed that were consistent with the few changes in the extra- and intracellular As speciation for the other two algae with Cu²⁺ inhibition and all the three algae with isothiazolinone inhibition, corroborating the above hypothesis again. All the algae tested in this study demonstrated great abilities for As transformation and release, as seen by the much higher rates of 86.11–99.98% and 81.11–99.89% for transformation and release when compared to the control, respectively. When inhibitors were added, the transformation and release values of only A. flosaquae decreased remarkably down to 72.37–86.79% and 64.67–85.24%, respectively, while no changes were seen for these values in the other two algae, indicating that growth stress did not affect the As transformation and release of the other algae. The biological productivity of As by the three algae followed the order of M. aeruginosa, Chlorella sp., and A. flosaquae, which was generally consistent with the As transformation and release in conditions with and without inhibitors, suggesting that the As behavior in the algae that was related to growth stress largely differed among algae species.

During the last decade, hydrogels have been used as potential adsorbents for removal of contaminants from aqueous solution. To improve the adsorption efficiency, there are numerous different particles that can be chosen to encapsulate into hydrogels and each particle has their respective advantages. Depending on the type of pollutants and approaching method, the particles will be used to prepare hydrogels. The hydrogels commonly applied in water/wastewater treatment was mainly classified into three classes according to their shape included hydrogel beads, hydrogel films, and hydrogel nanocomposites. In review of many recently research papers, we take a closer look at hydrogels and their applications for removal of contaminants, such as heavy metal ion, dyes, and radionuclides from water/wastewater in order to elucidate the reactions between contaminants and particles and potential for recycling and regeneration of the post-treatment hydrogels. Graphical abstract ᅟ

The toxicity of Roundup Original® (GLY), a glyphosate-based herbicide widely used in crops in Mato Grosso state, was determined in hybrid fish jundiara or pintado da Amazônia. The 96 h-LC₅₀ of GLY was 13.57 mg L⁻¹. Moreover, exposure to sublethal concentrations of GLY (0, 0.37, 0.75, 2.25, 4.5, 7.5 mg L⁻¹) has not altered the survival rate (100% for all treatments). In fish liver, protein carbonyl (PC) levels as well as glutathione-S-transferase (GST) activity, reduced glutathione (GSH), and ascorbic acid (ASA) contents increased when compared to control group. Superoxide dismutase (SOD) activity was reduced and catalase (CAT) has not changed. PC content has grown in muscle and brain, and thiobarbituric acid-reactive species (TBARS) levels also increased in muscle, but in the brain, they remained unaltered. Acetylcholinesterase (AChE) activity reduced in muscle but increased in brain when compared to control group. Our results suggest that short-term exposure to GLY induced alterations in the oxidative stress biomarkers in fish and can be interfering with their survival in natural environment; besides, these findings may be considered of high ecotoxicological relevance.

Soil contamination with heavy metals is a worldwide problem especially in China. The interrelation of soil bacterial community structure, antibiotic resistance genes, and heavy metal contamination in soil is still unclear. Here, seven agricultural areas (G1–G7) with heavy metal contamination were sampled with different distances (741 to 2556 m) to the factory. Denaturing gradient gel electrophoresis (DGGE) and Shannon index were used to analyze bacterial community diversity. Real-time fluorescence quantitative PCR was used to detect the relative abundance of ARGs sul1, sul2, tetA, tetM, tetW, one mobile genetic elements (MGE) inti1. Results showed that all samples were polluted by Cadmium (Cd), and some of them were polluted by lead (Pb), mercury (Hg), arsenic (As), copper (Cu), and zinc (Zn). DGGE showed that the most abundant bacterial species were found in G7 with the lightest heavy metal contamination. The results of the principal component analysis and clustering analysis both showed that G7 could not be classified with other samples. The relative abundance of sul1 was correlated with Cu, Zn concentration. Gene sul2 are positively related with total phosphorus, and tetM was associated with organic matter. Total gene abundances and relative abundance of inti1 both correlated with organic matter. Redundancy analysis showed that Zn and sul2 were significantly related with bacterial community structure. Together, our results indicate a complex linkage between soil heavy metal concentration, bacterial community composition, and some global disseminated ARG abundance.