Variations in the composition of stable isotopes of mercury contained in tissues (root, stem, leaf, and hypocotyl or flower) of three typical mangrove plants (Kandelia candel, Aegiceras corniculata, and Bruguiera gymnorhiza), collected from the mangrove wetland of Jiulong estuary, SE China, were used to investigate the sources and transformation of mercury in the mangrove plants. Tissue samples from the plants were digested and mercury in the solution was pre-concentrated with purge-trap method and then analyzed by multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS). The results showed that the mass dependent fractionation (MDF) of mercury ranged from −2.67 to −0.87 ‰ for δ ²⁰²Hg while the mass independent fractionation (MIF) of mercury isotopes ranged from −0.16 to 0.09 and −0.19 to 0.05 ‰ for Δ¹⁹⁹Hg and Δ²⁰¹Hg, respectively, relative to the standard NIST SRM 3133. The ratio of Δ¹⁹⁹Hg/Δ²⁰¹Hg was 0.991, indicating that the mercury had been photo-reduced before being accumulated in mangrove plants. Analyses of the data from MIF studies revealed that the major portion of the mercury measured in leaves (∼90 %) originated from the atmosphere while the source of over half of the mercury present in roots was the surficial sediment. This study, the first of its kind investigating the variations in isotopic composition of mercury in the tissues of mangrove plants, could be helpful to identify the source of mercury contamination in mangroves and understand the biogeochemical cycle of mercury in the estuarine mangrove wetlands.

For the treatment of high-strength pyridine containing wastewater, a bioaugmented continuous-flow self-forming dynamic membrane bioreactor (CSFDMBR), which was consisted of a continuous flow airlift reactor (CFAR) and a dynamic membrane bioreactor (DMBR), was developed in this study. The results indicated that through the bioaugmentation by Rhizobium sp. NJUST18, CSFDMBR could be successfully started, which was confirmed by complete removal of pyridine, efficient nitrification, and significant increase of biomass. Pyridine could be effectively degraded in the CSFDMBR even at influent pyridine loading rate as high as 9.0 kg m⁻³ day⁻¹, probably due to the efficient biomass retention in the CSFDMBR, which could be attributed to the formation of aerobic granules and the key role of dynamic membrane. CSFDMBR presented good polishing performance in treating pyridine wastewater, with effluent total organic carbon (TOC) and turbidity as low as 22.5 ± 6.8 mg L⁻¹ and 3.8 ± 0.5 NTU, respectively. Membrane fouling could be effectively controlled, as indicated by backwash period as long as 60 days. The observed efficient performance highlights the potential for the full-scale application of the bioaugmented CSFDMBR, particularly for highly recalcitrant pollutant removal.

In this article, Cr(OH)₃ nanoparticle-modified cellulose nanocrystal (CNC) as a novel hybrid nanocomposite (Cr(OH)₃-NPs-CNC) was prepared by a simple procedure and used as a sorbent for adsorptive removal of methylene blue (MB) and malachite green (MG) from aqueous solution. Different kinetic models were tested, and the pseudo-second-order kinetic model was found more suitable for the MB and MG adsorption processes. The BET and Langmuir models were more suitable for the adsorption processes of MB and MG. Thermodynamic studies suggested that the adsorption of MB and MG onto Cr(OH)₃-NPs-CNC nanocomposite was a spontaneous and endothermic process. The maximum adsorption capacities for MB and MG were reached 106 and 104 mg/g, respectively, which were almost two times higher than unmodified CNC. The chemical stability and leaching tests of the Cr(OH)₃-NPs-CNC hybrid nanocomposite showed that only small amounts of chromium were leached into the solution.

In a previous study, we found that rice-straw biochar degraded and removed hydrophobic organic contaminants (HOCs) through coupled adsorption-biodegradation. However, few studies have determined whether biochar affects HOC isomer degradation and isomer-selective biodegradation or whether biochar can alter HOC isomer features, resulting in changes to HOC isomer residues in water environments. In this study, the effects of biochar at two dosages (0.001 and 0.01 g) on the biodegradation of ten isomers of a typical xenoestrogen of nonylphenol (NP) were evaluated. The results revealed that there were no effects of biochar on the adsorption of NP isomers. However, biochar addition affected the biodegradation of a specific isomer without altering the features of the NP isomers. The treatment of NP isomers with Pseudoxanthomonas sp. yielded degradation ratios ranging from 60.7 to 100%. At 0.001 g biochar treatment, the degradation of eight NP isomers was enhanced (except for NP₁₉₄ and NP₁₉₃ₐ₊b) due to their bulky structures. The degradation of the ten NP isomers was inhibited when 0.01 g biochar was added. These findings characterized the effects of biochar on NP isomer contaminants and provided basic information for the application of biochar for the remediation of NP isomer contaminants.

The possibility of using different densities of cherry tomato as a bio-filter in a simple media-based aquaponic system to recycle nutrients from pearl gourami intensive culture wastewater was evaluated. Water quality parameters including total ammonia nitrogen (TAN), nitrite (NO₂ ⁻), nitrate (NO₃ ⁻), phosphate (PO₄ ³⁻), pH, and dissolved oxygen (DO) were determined in outlet of the aquaponic system during a 60-day experimental period. Cherry tomato was planted at four densities of 0 (control), 3 (T1), 6 (T2), and 9 (T3) plants per aquaponic unit with a constant fish stock density. Each treatment was equipped with aquaponic systems containing fish tank and plant growing bed. Productivity of the system was measured by recording the fish and plant growth indices. The potential in removing nitrogen of the water was the highest in T3 (with nine plants) compared to other treatments (p < 0.05). The highest concentrations of TAN (6.59 ± 0.241 mg/L), nitrite (0.42 ± 0.005 mg/L), nitrate (0.45 ± 0.162 mg/L), and phosphate (30.47 ± 0.371 mg/L) were obtained in control group, while the lowest concentrations of TAN (0.05 ± 0.091 mg/L), NO₂ ⁻ (0.11 ± 0.008 mg/L), NO₃ ⁻ (29.77 ± 0.205 mg/L), and phosphate (18.59 ± 0.185 mg/L) were detected in T3 (p < 0.05). The maximum fish weight gain was recorded in T3 (26 ± 0.014%) with 1.26 ± 0.059 FCR, and the lowest fish weight gain was measured in the control group (15 ± 0.024%) with 2.19 ± 0.446 FCR (p < 0.05). Total plant length gain was reached at the maximum value in T3 (74.70 ± 1.153 cm) in comparison to other groups (p < 0.05). It was concluded that small-scale aquaponic growing bed system can be created a sustainable ecosystem which both the plant and fish can thrive and suitable for home-made production system.

Nitrogen fertilizer availability to plants is strongly linked with water availability. Excessive or insufficient use of nitrogen can cause reduction in grain yield of wheat and environmental issues. The per capita per annum water availability in Pakistan has reduced to less than 1000 m³ and is expected to reach 800 m³ during 2025. Irrigating crops with 3 or more than 3 in. of depth without measuring volume of water is not a feasible option anymore. Water productivity and economic return of grain yield can be improved by efficient management of water and nitrogen fertilizer. A study was conducted at post-graduate agricultural research station, University of Agriculture Faisalabad, during 2012–2013 and 2013–2014 to optimize volume of water per irrigation and nitrogen application. Split plot design with three replications was used to conduct experiment; four irrigation levels (I₃₀₀ = 300 mm, I₂₄₀ = 240 mm, I₁₈₀ = 180 mm, I₁₂₀ = 120 mm for whole growing season at critical growth stages) and four nitrogen levels (N₆₀ = 60 kg ha⁻¹, N₁₂₀ = 120 kg ha⁻¹, N₁₈₀ = 180 kg ha⁻¹, and N₂₄₀ = 240 kg ha⁻¹) were randomized as main and sub-plot factors, respectively. The recorded data on grain yield was used to develop empirical regression models. The results based on quadratic equations and economic analysis showed 164, 162, 158, and 107 kg ha⁻¹ nitrogen as economic optimum with I₃₀₀, I₂₄₀, I₁₈₀, and I₁₂₀ mm water, respectively, during 2012–2013. During 2013–2014, quadratic equations and economic analysis showed 165, 162, 161, and 117 kg ha⁻¹ nitrogen as economic optimum with I₃₀₀, I₂₄₀, I₁₈₀, and I₁₂₀ mm water, respectively. The optimum irrigation level was obtained by fitting economic optimum nitrogen as function of total water. Equations predicted 253 mm as optimum irrigation water for whole growing season during 2012–2013 and 256 mm water as optimum for 2013–2014. The results also revealed that reducing irrigation from I₃₀₀ to I₂₄₀ mm during 2012–2013 and 2013–2014 did not reduce crop yield significantly (P < 0.01). The excessive nitrogen application ranged from 31.2 to 55.4% at N₁₈₀ and N₂₄₀ kg ha⁻¹ for different levels of irrigation. It is concluded from study that irrigation and nitrogen relationship can be used for efficient management of irrigation and nitrogen and to reduce nitrogen losses. The empirical equations developed in this study can help farmers of semi-arid environment to calculate optimum level of irrigation and nitrogen for maximum economic return from wheat.

Aryl hydrocarbon receptor (AHR) is responsible for crucial events in male reproductive biology. Here, the association of the AHR transitions c.-742C>T and c.1661G>A with idiopathic male infertility was investigated in a case-control study, which is followed by a meta-analysis and a bioinformatic investigation. Blood and semen samples were obtained from a total of 135 idiopathic infertile men and 130 healthy controls. Participants were genotyped for the transitions using a PCR-RFLP method. A meta-analysis of five sets of data evaluated the association of c.1661G>A with male infertility, and using an in silico analysis, the possible molecular effects of the transitions predicted. Genotypes and alleles of AHR-c.-742C>T and c.1661G>A polymorphisms were not associated with the risk of male infertility significantly. However, the frequency of C/A haplotype was significantly associated with the increased risk of male infertility, and T/A haplotype was higher among controls significantly. Also, the frequencies of combined genotypes CT/GG, CT/GA and TT/GG were significantly associated with decreased risk of infertility. And, the meta-analysis showed that the AA versus GA/GG recessive model is associated with decreased risk of male infertility among the Iranian population. In silico analysis predicted that c.-742C>T does not alter the binding sites of the proposed transcription factors, but c.1661G>A poses a tolerable structural disturbance in AHR protein. In conclusion, these results showed that AHR c.-742C>T and c.1661G>A transitions separately could not be nominated as a risk or protective factor for male infertility. However, some combined models could affect infertility risk, especially among Iranian men.

Accumulation of nitrite in shortcut nitrification is influenced by several factors including dissolved oxygen concentration (DO), pH, temperature, free ammonia (FA), and free nitrous acid (FNA). In this study, a model based on minimum dissolved oxygen concentration (DOₘᵢₙ), minimum/maximum substrate concentration (Sₘᵢₙ and Sₘₐₓ), was developed. The model evaluated the influence of pH (7–9), temperature (10–35 °C), and solids retention time (SRT) (5 days–infinity) on MSC values. The evaluation was conducted either by controlling total ammonium nitrogen (TAN) or total nitrite nitrogen (TNN), concentration at 50 mg N/L while allowing the other to vary from 0 to 1000 mg N/L. In addition, specific application for shortcut nitrification-anammox process at 10 °C was analyzed. At any given operational condition, the model was able to predict if shortcut nitrification can be achieved and provide the operational DO range which is higher than the DOₘᵢₙ of AOB and lower than that of NOB. Furthermore, experimental data from different literature studies were taken for model simulation and the model prediction fit well the experiment. For the Sharon process, model prediction with default kinetics did not work but the model could make good prediction after adjusting the kinetic values based on the Sharon-specific kinetics reported in the literature. The model provides a method to identify feasible combinations of pH, DO, TAN, TNN, and SRT for successful shortcut nitrification.

Mixture of metals and herbicides in rivers may pose relevant risks for the health of surrounding communities. Humans may be exposed to river pollution through intake of contaminated water and fish, as well as irrigated agricultural products. The aim of this study was to assess the human health risks of environmental exposure to metals and herbicides through water and fish intake in the Pardo River. Metals (Al, As, Be, Cd, Cr, Cu, Pb, Mn, Hg, Ni, Tl, Sn, V, and Zn) were analyzed in river water and in edible fish. Herbicides (ametryn, atrazine, diuron, hexazinone, simazine, and tebuthiuron) were analyzed in river water. Seasonal variances were also studied. Aluminum, Cd, Cu, Mn, Pb, and Zn levels in river water were higher than the USEPA benchmarks. Non-carcinogenic risks due to pollutants mixture exposure were above the limit, and carcinogenic risks of As exposure were >10⁻⁶ in the sampling points during the rainy season. Metal levels in fish were lower than the Brazilian legislation and do not pose a threat to public health. Herbicides were detected in four sampling points, with atrazine concentrations (range 0.16–0.32 μg/L) below the Brazilian standard (2.0 μg/L), but above the European Union standard (0.1 μg/L). Considering the water supply needs of cities located in the Pardo River Basin and the persistence of metals and herbicides, the present study indicated that there was a seasonal influence on non-carcinogenic and carcinogenic risks to human health, especially in the rainy season. Studies for water treatment plants implantation should consider the risks of exposure to persistent substances, in order to protect the population.

The present study was designed to investigate the residual decline pattern and the risk assessment of 10 different class pesticides, namely azoxystrobin, boscalid, diazinon, diethofencarb, difenoconazole, etofenprox, flubendiamide, paclobutrazol, and pyraclostrobin in young vegetative amaranth (Amaranthus mangostanus) sprayed once or twice under greenhouse growing conditions. Field-incurred samples, collected at 3, 7, or 10 days after application of both treatments, were extracted and purified with the quick, easy, cheap, effective, rugged, and safe “QuEChERS” citrate-buffered method and analyzed with liquid chromatography-electrospray ionization tandem mass spectrometry (LC-MS/MS) in positive ion mode. The linearity was satisfactory with determination coefficients (R ²) falling between 0.9817 and 0.9999 and limits of detection (LOD) and quantification (LOQ) values of 0.0007 and 0.002 mg/kg, respectively. The mean recovery rate at four spiking levels (equivalent to 5, 10, 50, and 100 × LOQ) ranged from 78.1 to 131.6% with a relative standard deviation (RSD) of < 11%. Substantial differences in the initial deposit between the tested analytes were observed and clearly indicated that the structure, as well as the initial concentration of applied products, greatly affected the residue deposit. From the obtained residual data, the provisional marginal maximum residue limits (MRLs) and the pre-harvest intervals (PHI) were proposed. Risk assessment was evaluated by comparing the theoretical maximum daily intake (TMDI) with the acceptable daily intake (ADI). Herein, the TMDI was lower than the ADI (TMDI/ADI ratio ≤ 80% set by the Korean Ministry of Food and Drug Safety) except for difenoconazole (80.92%, marginally higher), indicating that the vegetative amaranth is not hazardous and can be consumed safely by Korean consumers.