The main purpose of the present experiments was to investigate the effect of various hydrogen peroxide (H2O2) concentrations and for various lengths of treatment on the total carotenoid, β–carotene content, colour intensity and microbiological safety on the fresh shredded carrots. Shredded carrots were dipped in 0.5, 1.0 and 1.5% H2 O2 water solution for 30 ± 1s, 60 ± 1s and 90 ± 1s. Negative effect of H2 O2 on β–carotene content and colour parameters of analyzed shredded carrots samples was not detected. In carrots treated with H2 O2 (p = 0.008) for 60 – 90s the total content of carotenoids significantly decreased during treatment compared to untreated carrot samples. There was significant difference (p is less than 0.05) observed between treated and non–treated shredded carrot samples on the total bacteria count. It was possible to reduce significantly (p is less than 0.05) the content of yeasts and mould up to 99.99% by shredded carrots treatment with 1.5% hydrogen peroxide water solution for 30 ± 1s. In the non–processed carrots E.coli was detected; however, it was possible to destroy E.coli by treating carrots with 0.5% H2 O2 water solution for 30 ± 1s. Considering all experimentally obtained results, we have concluded that fresh shredded carrots could be treated in water with the addition of hydrogen peroxide 1.5% for 30 ± 1s to maintain quality.

Fruits and vegetables are a major source of antioxidants. The aim of current research was to study and compare the antiradical activity, the total polyphenol content (TPC) and the total flavonoid content (TFC) in dried carrots (Daucus carota), pumpkins (Cucurbita maxima), leeks (Allium ampeloprasum var. porrum) and black radish (Raphamussativus) using a traditional convective drier and a microwave-vacuum drier. For each vegetable steaming as pre-treatment was used. Vegetables were harvested in Latvia in 2012, gathered when ripe and then dried. Analyses were made in Latvia University of Agriculture, Faculty of Food Technology laboratories. The total polyphenol content was determined by the Folin- Ciocalteu method and the total flavonoid content - using spectrophotometric method. The antiradical activity was analyzed by the 2,2-diphenyl-1-picrilhydrazyl (DPPH) assay. The results of experiments demonstrate that the total amount of polyphenols ranged from 98.97 to 623.70 mg gallic acid equivalent (GAE) 100 gE-1 in dry weight and the total amount of flavonoids ranged from 40.32 to 100.23 mg catechin equivalent (CE) 100 gE-1 in dry weight. The value of DPPH antiradical activity for vegetable samples ranged from 6.10 to 45.14 percents.

Malt is a natural food product produced by germinating cereal grains. Safety of cereal grains and cereal products is a very important area. Experiments were carried out at the Faculty of Food Technology of the Latvia University of Agriculture. The research object was rye malt. The purpose of the research was to investigate and compare the influence of copper and selenium on microbiological indicators of rye malt. Rye grains of 96% viability were soaked and germinated at temperature +6 ± 2 °C for 4 days, using copper(II) sulphate pentahydrate CuS04*5H2 O solutions (Cu concentration 10 mg LE-1, 50 mg LE-1, 100 mg LE-1) and for 3 days using sodium selenate Na2 SeO4 solutions (Se concentration 3 mg LE-1, 5 mg LE-1, 10 mg LE-1) then the soaked grains dried in the oven for 24 hours. The total plate count and yeast colony forming units were determined in rye malt samples. The obtained results showed that the increasing of copper and selenium concentration in solution significantly changes microflora of rye malt comparing with the control sample.

The aim of investigations was to compare different absorber material efficiency to examine collector tracking the Sun and stationary collector efficiency as well as the efficiency of insulated and non-insulated collectors. The 0.1x0.5x1.0 meter long experimental solar collectors were constructed for investigations and different types of absorber materials were made. The manifold length, the Sun radiation effect on the degree of air heating was analyzed. ASHARE used standard 93-2003 is determined for insulated and non-insulated solar collectors and absorber effectiveness. We determined the influence of the Sun radiation on the air heating degree for those types of absorbers. The experimental data were measured and recorded in the electronic equipment REG (electronic metering and recording equipment of temperature, radiation and lighting). The collector covered material was a polystyrol plate and different absorbers. We compared insulated and non-insulated collectors to prove that the insulated collector is more effective. The insulated collector was made of the collector surfaces faced with cellular plastic two cm plates. Our task was to calculate the air heating solar collector efficiency. The collector tracking the Sun is approximately 30% more efficient than the same type of stationary collectors in operation time for 6 hours. Insulation increases solar panel efficiency especially in windy weather. The insulated collector demonstrates almost two times higher efficiency than the non-insulated collectors (up to 93%) with absorbent material steel tinplate on top.

The paper contains description of the working principles and evaluation of the operational parameters of the commercially available fuel conversion adapter, intended to adapt gasoline fuelled spark ignition (SI) engine for use of high ethanol content blended fuel, known as E85. Commercially available gasoline and E85 fuel were used as test fuels. Production automobile, equipped with 1.8 litre 4 cylinder SI port fuel injection (PFI) engine was tested on the roll-type eddy-current chassis dynamometer in wide open throttle (WOT) constant speed mode. High precision fuel consumption measurement system AVL KMA Mobile was used. Engine operating parameters, used for evaluation of the efficiency of the fuel conversion adapter was engine torque (T), engine brake power (Pb ), air/fuel equivalence ratio (λ), specific fuel consumption (SFC) and engine thermal efficiency (ηt ). Analysis of engine operational parameters showed successful operation of fuel conversion adapter with E85 fuel, resulting in increase of engine peak torque by 4.4%, increase of energy efficiency in whole tested engine speed range up to 6.1% but increase of specific fuel consumption by approximately 22%, when compared with the gasoline use.

This research deals with tendencies of growth of Norway spruce Picea abies (L.) Karst. during last 50 years (1960 – 2010) in eastern part of Latvia emphasizing trendal specificity of active periods during the first (t1: 1960-1985) and the second (t2: 1986-2010) time interval. There have been 150 superior stand trees bored in six mixed pine-spruce Pinus sylvestris L. – Picea abies (L.) H.Karst. stands. An active period of factor’s impact is the time span when some meteorological factor (decade average, minimal or maximal temperature and sum of decade precipitation) influences an increase of annual ring width significantly. Comparing average temperatures from two weather stations included in this research the difference between interval t1 and t2 is approximately 1 °C. Active periods of temperature impact on growth of Norway spruce in eastern part of Latvia during last decades have changed not only their location but also an impact direction from positive to negative. Minimal and maximal decade temperatures are those mostly determinating the radial growth of Norway spruce in the eastern part of Latvia. Interval t2 is quite rich in active periods both from minimal and maximal decade temperature. Research results prove hypothesis about trendal shift of meteorological factors’ impact active periods due to climate change. An increase in decade precipitation level in winter caused annual ring growth positively both in the interval t1 as well as in t2.

The aim of this paper is to characterize and ascertain quality influencing factors of wood chips produced from forest residues in clear-cuts. The quality of food fuels varies according to the harvesting season, site characteristics and silvicultural treatment. For this study 89 piles of logging residues from clear-cuts located in Western part of Latvia were used. Piles were stored in different parts of clear-cut according to its direction against nearby stand. Piles of logging residues were pre dried and then chipped. A period of chipping and sample acquisition was from February to May of the year 2012. Results show that chips from forest residues can be successfully used for medium scale boilers. Chips with lower carbon content, calorific value, relative moisture and bulk density of wet chips can be produced in May. Location of the pile in centre and SE part of the clear cuts can decrease resulting ash content in wood chips.

The stump lifting trials were implemented in 5 forest compartments of the JSC ‘’Latvia state forest’’ Vidusdaugava, Rietumvidzeme, Zemgale and Ziemeļkurzeme forestries in autumn, 2012. Total extracted area was 3.5 ha, excluding control. Two stump extraction buckets were compared in these trials – CBI (made in Canada) and MCR-500 (made in Latvia). The scope of the study was to estimate if the prototype of the MCR-500 can compete with stump lifting buckets having positive feedback from industry. Considering that the CBI head cannot prepare soil, this operation was not done by the MCR-500 either. In total 1796 stumps were marked and their main parameters were taken in all trial areas. Extracted biomass was estimated theoretically using biomass expansion factors elaborated in Nordic countries. Allegro CX field computers with SDI software were used in time studies to obtain information about productivity and distribution of productive time in a work cycle. The study demonstrated that productivity of stump extraction with both stump lifting buckets did not differ significantly in 6 cases out of total 10 comparisons.

Heavy metals are worldwide spread pollutants in soils of functioning as well as abandoned industrial territories, landfills, military areas with its historical contamination, and other sites contaminated by industrial activities. Development of soil and groundwater remediation technologies is a matter of great importance to diminish the hazardous impact of pollution to humans and environment. Sustainable solution can be found for remediation of industrial areas using the stabilization/solidification (S/S) technology, which refers to binding of waste contaminants to a more chemically stable form. Geotechnical properties of soil treated with Portland cement (PC) can be improved when municipal solid waste incineration (MSWI) ash is used as the combined additive. Ash is composed mainly of metals, so environmental impact must be evaluated if it is used as amendment in the cement industry. The use of MSWI ash in stabilization of contaminated soils would be useful for the sustainable environmental management in two ways: S/S contaminated soil gains better geotechnical stability and waste incineration industry gets rid of the ash with high metal content. The aim of research is to provide pilot batch experimental results for leaching of heavy metal compounds when S/S technology is used for contaminated soils using PC and MSWI bottom ash additives. Mineral soils were spiked with copper, PC and MSWI were added in known proportions and leaching tests applied. Main results show that PC addition allows to chemically stabilizing soil; thus, heavy metals are not leached out from combined mass of spiked soil and MSWI bottom ash.

Roads play an important role in our daily surroundings and provide access to landscape. Views from the road create the first impression about the country. It is important to pay attention to the landscapes along the roads used by tourists. The purpose of this study was to obtain general overview of the current state, identify existing and disappearing features of the road landscape in Latvia. Research on road landscape perception and design is well developed in the USA and some countries in Europe. The assessment of the current state and proposals for the road landscape development in Latvia are fields which are little discussed and need more attention. The research was carried out in several sections of the main roads and some sections of regional and local roads in July and August, 2011 and August, 2012. Photography method was used. Analysis of the results shows that the main reasons of aesthetic quality loss in road landscapes is lack of planning and management, indicating the necessity to find ways for rural landscape quality enhancement.